Starlink Installation cost at a glance
- Typical range: $550 – $850
- Most homeowners pay: around $700
Cross-checked against one published sources for this project. Sources used for this page: LeoSatNetwork, Starlink Installation (2026) (figures checked on starlink.com Sep 17 and Oct 21, 2026 — the most current primary check; Residential plans 100 Mbps $55/mo, 200 Mbps $85/mo free professional home installation, Max $130/mo free professional home installation where available; hardware no upfront cost in select areas, otherwise $349 for the Standard kit or $10/mo to rent where offered; Mini kit starts at $199; official pro install via partner OnTech included with Residential 200 Mbps and Max where available, $199 with the 100 Mbps plan, covering a standard roof or wall mount, one cable entry through a wall, router setup and activation; independent installer published 2026 ranges: single-story standard install $100–$350, two-story or complex roofs $300–$600, pole or ground mount on a wooded rural property $350–$600, network extensions $400–$800 and up, RV/truck installs quoted per vehicle; HOA/permits: FCC OTARD rule generally protects an antenna under one meter on property you own or rent exclusively, residential mounts rarely need a permit, local rules vary; dish needs a clear sky view, tilted north in the US; cable must not be cut or spliced; Standard kit's router is Wi-Fi only — wired devices need the Ethernet adapter), Budget Seniors, Starlink Installation (2026) (https://www.budgetseniors.com/starlink/starlink-installation/ — published 2026-10-23, prices checked October 22, 2026 against Starlink's US residential plans page and help center, technically reviewed; official install free on Residential 200 Mbps $85/mo and Max $130/mo, $199 on the Residential 100 Mbps plan $55/mo, US partner OnTech (844) 800-7332; independent installer commonly $200–$500+; Standard kit lists at $349 to buy, “no upfront hardware cost in select areas”, Mini recently advertised at $149 in the US; mount prices pipe adapter ~$20–$45, wall mount ~$25–$120, pivot roof mount ~$20–$130, ground pole $40–$150 plus concrete, non-penetrating ballast $60–$200, Mini mounts ~$25–$60; Standard kit includes a 15 m cable, about 49 feet; standard pro install includes site assessment, standard mount, cable to nearest entry, activation — “nearest entry point” only, router in a back bedroom or cable inside walls to a second floor is outside the standard job; kickstand setup minutes, DIY roof/wall mount usually an afternoon, professional standard installation typically a couple of hours; FCC OTARD protects dishes one meter or smaller on property owned or exclusively controlled; grounding NEC Article 810 covers mast bonding; DIY costs nothing but parts, often under $200 for a permanent mount), Budget Seniors, Does Starlink Have an Installation Fee? (https://www.budgetseniors.com/starlink/does-starlink-have-an-installation-fee/ — same family as B1, no publication date visible, search index last-updated ~71 days before 2026-11-11, OLDER than B1, technically reviewed; CONFLICTS with B1 and with LeoSat on the official install: “the company charges $199 for the Residential 100 Mbps AND 200 Mbps plans. Subscribers on the Residential MAX plan get professional installation included at no extra cost” — publish the newer claim, flag the older one; third-party installers typically $200–$600; Standard Kit $349, dish, Wi-Fi 6 router, 82-foot cable, kickstand base; shipping flat $50; sales tax roughly 5–10%; congestion surcharge $100–$1,500 at checkout; mounts pipe adapter $35–$50, wall mount $50–$75, pivot roof mount $50–$80, non-penetrating ridgeline clamp $60–$100, third-party mounts from ~$20, Ethernet adapter $25, cable extension ~$30 max run 150 ft; budget $50–$250 in accessories beyond base hardware; DIY self-install $0 labour, most finish in under 2 hours; “about 65% of new Starlink customers successfully self-install” and “35% of new Starlink buyers end up paying someone” are SINGLE-SOURCE stats with no methodology given — do NOT print either), Budget Seniors, Starlink Equipment Cost (2026) (https://www.budgetseniors.com/starlink/how-much-does-starlink-equipment-cost/ — updated October 2026; Standard dish about $349 to buy, Mini about $150 reported $149 in October, down from $249, Performance kit $1,999 business, out of scope; install DIY $0 about 20–30 minutes, Starlink pro install from about $199, independent installer about $100–$350 simple, $350–$600 complex, big-box store installation reported around $329; “one guide's average for a professional job was about $300, with a range of $200 to $500” — SECOND-HAND citation of an unnamed guide, not a published survey average, usable only as a cross-check, never as a published average; mounts pipe adapter $25–$40, J-mount $20–$60, ridge or roof mount $50–$100, pole/ground mount $40–$150 plus pipe, official pivot/flashing mounts $35–$85, cable extension about $30–$35, Ethernet adapter $25, mesh node $99–$149 each, cable gland/ground block $8–$25, surge protector/battery backup $40–$150; shipping about $20–$50, sales tax roughly 5–10%, congestion surcharge $100–$1,500, electricity about $3–$22/mo Standard dish 75–100 W; FIVE SETUPS PRICED, labelled by the source as “original estimate built from the price ranges reported in this guide ... planning numbers, not quotes”, tax assumed ~7% of the dish, none includes the monthly plan: Mini DIY ~$179, Standard DIY on a pole ~$393, Standard roof + one mesh node ~$597, Standard store pro install ~$652, complex job large home ~$1,201; rural-home guidance budget about $400–$650 up front depending on mount and install before any congestion surcharge; Standard kit contents per this page dish, router, 75-foot cable and base mount — conflicts with B1's 49 ft and B2's 82 ft), BroadbandNow, How Much Does Starlink Cost in My Area? (https://broadbandnow.com/guides/starlink-cost-by-location — published 2026-08-26, updated 2026-10-23; Residential plans $55–$130/mo, zero upfront equipment costs aside from a shipping fee of $20, congestion fee $100–$1,500 in select areas; Standard kit $349, Mini kit $199–$349, Flat High-Performance kit $1,999, rental $0–$10/mo where offered; professional installation third-party contractor fees typically $150–$300 for labour — mount the dish, run external cabling through exterior walls, seal entry points, “Estimated Starlink professional installation cost: $150–$300 total for labor, excluding the price of specialty mounting brackets”; shipping standard flat-rate typically $20 inside the continental US; accessories pivot/wall mount $60–$85, pipe adapter $40–$50, Ethernet adapter $25–$45, extended cable 150 ft $70–$90, Starlink mesh Wi-Fi node $120), ThePricer, How Much Does Starlink Cost? (https://www.thepricer.org/how-much-does-starlink-cost/ — updated June 27, 2026, “researched using 12 sources”; Residential monthly service $55–$130, Standard residential kit commonly around $349 may be discounted, rented, or $0 upfront in select areas, Mini kit about $249; professional installation $100–$500+; mounts wall/roof $40–$150+, pipe adapter or pole mount $30–$100+, longer cable $50–$150+, Ethernet adapter or network hardware $25–$200+; demand surcharge or regional fee $0–$250+ — far below the $100–$1,500 in BroadbandNow and Budget Seniors, the outlier, likely a different fee or an older figure), Allconnect, Starlink Cost and Plans: 2026 Review (https://www.allconnect.com/providers/starlink — published 2026-10-29, updated 2026-10-29; Residential 100 Mbps $55/mo, 200 Mbps $85/mo, Max $130/mo, Roam $55/$80/$175, speeds up to 100/200/400 Mbps; equipment costs vary by location: “In some areas, the self-install Starlink Kit costs $49 plus shipping. ... Other locations offer a discounted one-time equipment fee of $175, down from the original $349, along with select first-year plan discounts”, comparison table lists equipment cost $175 for self-installation; “some customers can also rent the dish and pay a $99 professional installation fee. Rented equipment must be returned when Starlink service ends”; no contract, kit returnable within 30 days of shipment for a full refund of the hardware payment). NOT used: StarNet Pros installer blog (vendor's own pricing page), Budget Seniors Canada installation guide (Canadian dollars), LeoSatNetwork UK guide (pounds), 1770 AdvisorsSearch seniors guide (snippet only), WeConnectSky Canada guide (snippet only). The $700 most-pay is a DERIVED midpoint of the derived $550–$850 band — no source read publishes a national average total for this spec; do NOT print the $300 “one guide's average” as a most-pay (labour-only, cited second-hand from an unnamed guide); do NOT print the $599 kit price or the $120/mo flat plan price from older guides (superseded: kit $349, plans $55/$85/$130); do NOT print Budget Seniors' 65%/35% self-install stats (single-source, no methodology).. Sources last checked: October 2026 — ThePricer. How we calculate these costs
Cost by scope

| Scope | Typical cost | What it includes |
|---|---|---|
| DIY — self-install | $390 – $550 all-in | Kit $349 (or $0 upfront in select areas) + mount $20–$150 + shipping $20–$50. The kickstand in the box is $0 and works for testing; a permanent mount is the real DIY cost. Budget Seniors' published DIY-pole scenario totals ~$393; its roof-mount + longer-cable scenario ~$490. Time: 20–30 minutes kickstand (B3), 1–2 hours for a wall/roof mount (B2), an afternoon per B1. Best for: clear yard sky, single-story shingle roof, anyone comfortable on a ladder. DIY is a genuine tier here — unlike most remodel jobs, Starlink is DESIGNED for self-install. |
| Standard — pro roof install | $550 – $850 | The most-pay tier — kit $349 + independent installer $200–$500, standard roof or wall mount, cable run, router placed and activated. The band most paid pro jobs land in. Official route for comparison: $349–$548 ($349 kit + $0–$199 official install, plan-dependent). A big-box store install is reported around $329 labour (B3) — kit + that = ~$678, inside the band. |
| Premium — pole mount + mesh + extended cable | $870 – $1,340 | Kit $349 + complex/pole labour $350–$600 (LeoSat pole $350–$600; complex $300–$600) + mesh node $99–$149 + longer cable $30–$90 + pole/mount hardware $40–$150. For tree-covered lots, two-story or metal roofs, long runs to outbuildings, or large homes needing mesh. Budget Seniors' published complex scenario (~$1,201: dish, $450 install, bigger mount, two nodes) sits inside this band. Tier totals are derived arithmetic from the published line items in the breakdown. |
Where the money goes
| Part of the job | Share | Note |
|---|---|---|
| Standard kit (dish + router + cable + kickstand) | No published share | $349 to buy (all sources); $0 upfront in select areas; $49 / $175 promotional prices reported by Allconnect in some areas. Rental ~$10/mo where offered (LeoSat, B2). Hardware prices are current retail that changes by address and over time. |
| Official pro install (OnTech, via Starlink at checkout) | No published share | $0 on the Residential 200 Mbps ($85/mo) and Max ($130/mo) plans, $199 on the 100 Mbps ($55/mo) plan (LeoSat, checked on starlink.com Oct 21, 2026; Budget Seniors B1, Oct 22, 2026). Covers a standard roof/wall mount, one cable entry, router setup and activation. $99 for rental customers (Allconnect). One older Budget Seniors page says $199 on the 200 Mbps plan too — the newer October 2026 sources say free; confirm the fee at checkout. |
| Independent installer labour | No published share | $100–$600 full published spread; standard-job honest overlap $200–$300 (LeoSat $100–$350; Budget Seniors $200–$500+; BroadbandNow $150–$300; ThePricer $100–$500+). Two-story or complex roofs $300–$600; pole or ground mount $350–$600; network extensions $400–$800 and up (labour alone, business / multi-building scope). |
| Mount hardware | No published share | $20–$150 (Budget Seniors B1 table; B3 $35–$150). Detail: pipe adapter $20–$50; wall mount $25–$120; pivot roof mount $20–$130; ground pole $40–$150 plus concrete; non-penetrating ballast $60–$200 (B1); BroadbandNow pivot/wall $60–$85, pipe adapter $40–$50. |
| Longer cable | No published share | ~$30–$35 for a short extension (Budget Seniors) vs $70–$90 for the 150 ft cable (BroadbandNow) — different lengths explain the gap. The cable must not be cut or spliced (LeoSat; Budget Seniors). Sources report 49 ft, 75 ft and 82 ft for the included cable in different kit generations — check the cable length for your kit generation. |
| Ethernet adapter + mesh node | No published share | Ethernet adapter $25 (Budget Seniors) / $25–$45 (BroadbandNow) — the Standard kit's router is Wi-Fi only, so wired devices need the adapter. Mesh Wi-Fi node $99–$149 each (Budget Seniors) / $120 (BroadbandNow). Cable gland / ground block $8–$25; surge protector / battery backup $40–$150 (B3). |
| Shipping + sales tax | No published share | Shipping $20–$50 (BroadbandNow $20 typical; Budget Seniors B2 flat $50; B3 $20–$50). Sales tax roughly 5–10% of hardware (Budget Seniors B2/B3). |
| Congestion / demand surcharge (excluded from install totals) | No published share | $100–$1,500 one-time at checkout in high-demand areas only (BroadbandNow; Budget Seniors B2/B3); ThePricer's $0–$250+ is the outlier. Address-only, shown at checkout; most addresses pay $0. NOT part of install cost. |
| Monthly service (recurring — never in install totals) | No published share | Residential $55 (100 Mbps) / $85 (200 Mbps) / $130 (Max) per month (all sources). No contract; cancel anytime (Allconnect). Electricity to run the dish ~$3–$22/mo (B3) is a running cost, not install cost. |

What moves the price most
Worked example — derived arithmetic from published line items (not a published quote): standard roof install, official route, 100 Mbps plan: Standard kit $349 + official install $199 + shipping ~$20–$50 + pivot roof mount ~$50–$80 = ~$618–$678, plus tax 5–10% and the first month of service ($55) billed separately. Same job, independent installer at the $200–$300 overlap: $349 kit + $250 labour + $50–$80 mount + $20–$50 shipping = ~$669–$729. Both routes land near the $700 most-pay — that is the cross-check, not a quote. The congestion surcharge ($100–$1,500 where it applies) is excluded because it is address-only. No source publishes a hardware-vs-labour percentage split for a Starlink install, so no percentage shares appear on this page — the split is shown in dollars only: at the $700 most-pay, $349 hardware + ~$350 install is roughly half-and-half BY ARITHMETIC, labelled as derived, never as a published share. What moves the price: the route chosen first — DIY ($0 labour) vs official OnTech install (free or $199) vs independent installer ($100–$600); the plan tier decides the official price, the single biggest swing in the total. Then roof height and pitch (single-story standard $100–$350 labour vs two-story/complex $300–$600; steep, metal, tile or slate roofs cost more and are the clearest case for a pro), obstructions and trees (heavy tree cover is the hardest install — solved by height or trimming, both of which add cost), mount type (kickstand $0, testing only; wall/pivot $20–$130; ground pole $40–$150 plus concrete; non-penetrating ballast $60–$200), cable run length and entry (a run past the included cable needs an official longer cable; routing through finished walls or to a far room is outside the standard official job and costs extra), mesh/coverage (a large home or thick walls need a mesh node at $99–$149 each or an Ethernet adapter at $25), grounding and surge protection in lightning country (NEC Article 810 mast bonding; ground block $8–$25, surge protection $40–$150), and the service address itself (hardware offers, plan tiers, congestion surcharge and the official-install offer are all decided by address). HOA / permits: the FCC OTARD rule generally protects an antenna under one meter on property you own or rent exclusively; residential mounts rarely need a permit, local rules vary. Renters are limited to exclusive-use areas and no-drill mounts. Roof warranty: drilling without proper flashing/sealant can void roofing warranty sections; non-penetrating mounts avoid this. Where sources disagree: independent pro-install labour — LeoSat $100–$350 basic / $300–$600 complex; Budget Seniors $200–$500+ (B1/B2) and $100–$350 simple / $350–$600 complex (B3); BroadbandNow $150–$300; ThePricer $100–$500+ (honest overlap for a standard job $200–$300; the low ends are simple single-story jobs, the high ends complex roofs, poles and long runs). Official install on the 200 Mbps plan — LeoSat and Budget Seniors B1 (both October 2026, one checked against starlink.com directly) say FREE; the older Budget Seniors B2 page says $199 on both 100 and 200 Mbps, free only on MAX (publish the newer claim; tell readers to confirm at checkout). Hardware — $349 is the agreed list price, but $0-upfront offers in select areas and Allconnect's $49 / $175 address-dependent prices mean the kit line is not one national number. Shipping — BroadbandNow $20 typical vs Budget Seniors B2 flat $50 vs B3 $20–$50 (publish $20–$50). Congestion surcharge — BroadbandNow and Budget Seniors $100–$1,500 vs ThePricer's $0–$250+ (the outlier — likely a different fee or an older figure). Longer cable — Budget Seniors ~$30–$35 vs BroadbandNow 150 ft $70–$90 (different lengths). Cable included in the Standard kit — B1 says 15 m (~49 ft), B3 says 75 ft, B2 says 82 ft (kit generations differ — do not state one length as fact). Mini kit price — $149 (Budget Seniors, October 2026) vs $199 (LeoSat) vs $249 (ThePricer, June 2026); prices move fast and the Mini is Roam/travel hardware, out of scope. DIY time — 20–30 minutes for a kickstand setup (B3) vs under 2 hours (B2) vs an afternoon for a DIY roof/wall mount (B1); all three describe different scopes. Scope — what this page is not: the monthly service fee ($55/$85/$130 — recurring, never in install totals); Starlink Mini / Roam travel hardware ($149–$249 reported) on Roam plans ($55/$80/$175 per month); the Performance / business kit ($1,999 hardware); the congestion surcharge (address-only checkout fee); RV / boat / maritime installs (quoted per vehicle); network extensions to outbuildings / failover ($400–$800+ labour alone — business / multi-building scope); satellite TV dish install (DirecTV/Dish Network — a different service with different hardware and pricing); TV antenna install (a different service); or generic Wi-Fi / router setup as a standalone job (the router is included in the kit and its setup is part of the install). Methodology: figures cross-checked across five independent data families — LeoSatNetwork (figures checked on starlink.com Oct 21, 2026), Budget Seniors (installation guide, prices checked Oct 22, 2026; equipment guide, Oct 2026), BroadbandNow (updated Oct 23, 2026), ThePricer (updated Jun 27, 2026), Allconnect (updated Oct 29, 2026); where sources disagree, the page publishes the honest overlap band and names the disagreement. Related costs: solar panel installation, ethernet wiring installation, smart home installation, security system installation, security camera installation, TV mounting, surround sound installation and generator installation.
Costs in your city
Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

Frequently asked questions
How much does Starlink installation cost?
$550–$850 for a standard residential kit professionally installed on a roof (kit $349 + independent installer $200–$500) — a derived band, not a published total. Most homeowners pay around $700 (derived midpoint). The official Starlink install is cheaper: free on the 200 Mbps and Max plans, $199 on the 100 Mbps plan — so the same job can total $349–$548 through Starlink itself. DIY labour is $0.
How much is the Starlink kit?
$349 for the Standard kit to buy (all sources), but $0 upfront in select areas, and Allconnect reports $49 in some areas and $175 discounted in others — the price depends on your address, so check the order page. The kit includes the dish, Wi-Fi router, cable and kickstand base. The Mini ($149–$249 reported) is travel hardware, not the home kit.
Is professional Starlink installation free?
On the Residential 200 Mbps ($85/mo) and Max ($130/mo) plans, Starlink lists professional installation as free where its partner OnTech operates (LeoSat, checked on starlink.com Oct 21, 2026; Budget Seniors, Oct 22, 2026). On the 100 Mbps plan it is reported at $199. One older Budget Seniors page says $199 on the 200 Mbps plan too — confirm the fee at checkout, because Starlink changes plan terms by address.
How much does Starlink cost per month?
$55 (100 Mbps), $85 (200 Mbps) or $130 (Residential Max) per month for Residential service (all sources). This is a recurring service charge and is NOT part of the installation cost — never add it into an install total. No contract; cancel anytime (Allconnect).
Can I install Starlink myself, or do I need a professional?
Yes — Starlink is designed for self-install: a kickstand setup takes 20–30 minutes and a wall/roof mount 1–2 hours to an afternoon (Budget Seniors). Hire a pro for a two-story or steep roof, tile/slate/metal roofs, long cable runs through finished walls, tall masts above trees, or grounding in lightning country — those fall outside the standard install (LeoSat; Budget Seniors).
How long does a Starlink installation take?
Minutes for a kickstand test setup; usually an afternoon for a DIY roof or wall mount; a professional standard installation typically takes a couple of hours (Budget Seniors). Test the dish on its kickstand for at least 24 hours before drilling anything (B1).






