Home › Cost Guides › Concrete Slab Installation
Cost Guide

How Much Does a Concrete Slab Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 17 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$5,400 – $7,200
Most homeowners pay around $5,500 · Concrete slab installation typically costs $5,400 – $7,200 for a standard 30-by-30-foot slab (900 square feet), with about $5,500 the figure most jobs land near — $5,500 is the mean of the two published national averages (Angi $5,400; Thumbtack $5,686), not a published average itself. That works out to $6 – $8 per sq ft installed for a plain 4-inch broom-finish slab, the honest overlap of Angi's $4–$8, HomeGuide's $6–$12, Thumbtack's $6–$9 and This Old House's $4–$8. A small shed pad can cost as little as $480, while a thickened-edge, reinforced or stamped slab the same size runs $7,200–$17,000. Fixr's lower $4–$6 per square foot band is for a basic monolithic garage slab, a narrower scope, and is published as such rather than merged into the general band.
typical
$5,400$7,200
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Workers in yellow hard hats pouring and levelling a fresh concrete slab, with a concrete mixer truck behind them and a worker operating a red power screed in the foreground

Concrete Slab Installation cost at a glance

  • Typical range: $5,400 – $7,200
  • Most homeowners pay: around $5,500
  • Per square foot: $6 – $8 per sq ft
  • Prices vary most by: Materials — concrete, gravel base, forms & reinforcement (50–60% of the budget)

Cross-checked against five published sources for this project. Sources used for this page: Angi, 'How Much Does a New Concrete Slab Cost? [2026 Data]', updated Oct 27, 2026 (national average $5,400; most homeowners pay $3,600-$7,200; $4-$8 per square foot; $110 per cubic yard; labour $2-$3 per square foot, one-third to one-half of the total; size table: 10x10 $600, 20x20 $2,400, 30x30 $5,400; thickness by project: patio 4-6 inches $6-$9, walkway 4 inches $6, sidewalk 4-6 inches $6-$9, driveway 4-8 inches $6-$12, foundation 8-10 inches $12-$18 per square foot; type: standard $6, rebar $7, high-strength $8, fiber mesh $10 per square foot; finishes: broom or smooth trowel $1-$3 or included, exposed aggregate $7-$15, stamped $10-$18, stained $8-$15, polished $3-$12 per square foot; pre-cast $5-$15; reinforcement: fiber mesh +$2-$3, rebar +$0.50-$1 per square foot; region $5.35 mid-country to $8.50 coastal — California $7.70-$8.50, New York $6.70-$8.50, Texas $5.30-$5.90, Kentucky $5.20-$5.70 per square foot; projects: shed 80 square feet $480, parking pad 200 square feet $1,200, patio 450 square feet $2,700, garage floor 350 square feet $2,100, 1-car driveway 240 square feet $1,440, 2-car driveway 500 square feet $3,000, RV pad 640 square feet $3,840, mobile home 1,620 square feet $22,680, home foundation 2,050 square feet $36,900; sealant $1.35-$2.50 per square foot; DIY saves $2-$3 per square foot in labour; resurfacing $3-$5 per square foot), HomeGuide, 'How Much Does a Concrete Slab Cost? (2026)', updated Feb 3, 2026 ($6-$12 per square foot installed total; materials $3-$7, labour $3-$5 per square foot; labour 40-50% of the total, materials 50-60%; thickness: 2 inches $4-$6, 4 inches $6-$8, 6 inches $8-$10, 8 inches $10-$12 per square foot; projects: shed $600-$4,800, patio $1,000-$6,000 at $4-$12 per square foot, garage floor $2,400-$6,900, driveway $2,400-$8,600 at $6-$15 per square foot, RV pad $1,200-$8,400, mobile home $3,600-$19,200, foundation $4,000-$33,600 at $6-$14 per square foot; stamped $8-$19 per square foot; removal $3-$8 per square foot; resurfacing $3-$7 per square foot; 30x30 feet $5,400-$10,800; gravel base $1-$3 per square foot; radiant heat $11-$25 per square foot; sealing $1-$3 per square foot; lifespan 30-50 years; walk on it in 1-2 days, drive on it in 1-2 weeks, full cure 28-48 days), Thumbtack, '2026 Concrete Price per Yard', published Apr 10, 2026 (national average $5,686, low $3,155, high $8,493, from Thumbtack pro data; $6-$9 per square foot; at $7.25 per square foot: 8x8 $464, 10x10 $725, 12x12 $1,044, 20x20 $2,900, 24x24 $4,176, 30x20 $4,350, 30x40 $8,700, 40x50 $14,500; concrete $150-$180 per cubic yard, via Concrete Network; removal $500-$1,800 per job; $3-$10 per square foot to pour; 20x30 slab about $3,900), This Old House, 'How Much Does a Concrete Slab Cost?', updated Mar 17, 2026 ($4-$8 per square foot; 30x30 $3,600-$7,200; thickness: 2 inches $5, 4 inches $5, 6 inches $6, 8 inches $8 per square foot; projects: parking pad $1,200, driveway $3,000, garage $3,500, fire pit $700, mobile home pad $9,720, monolithic slab foundation $12,300, patio $3,000, pool deck $8,000, RV pad $3,840, shed $480; stain or dye +$3.50-$7.50, stamping $10-$14, elaborate patterns $18-$20, epoxy or sealer +$4.50 per square foot; wire mesh $0.35, rebar $2-$3, thicker edges +$1-$2, styrofoam insulation $0.50-$2, vapour barrier $0.50 per square foot; lifespan 30-40 years; weight after 48 hours, full cure up to 28 days; 20x30 slab $2,400-$4,800; cubic yard $113-$126, covers 81 square feet at 4 inches). Corroboration, labelled and never the headline: Fixr (monolithic garage slab $4-$6 per square foot, up to $16 with heavier footings; 24x24 garage $2,304-$3,456; 12x20 one-car $960-$1,140; concrete pad $6-$12 per square foot; slab-on-grade foundation $4-$12 per square foot — via two independent 2026 transcriptions that agree verbatim, quickbuildcost.com checked Oct 25, 2026, costs.tudiencau.com and zarla.com Nov 2026; the direct Fixr URL returned 404 on 2026-11-17). INDEPENDENCE: Angi and HomeGuide sit in the same Angi Inc. data family and count as one confirmation, not two; the three independent confirmations are the Angi family, Thumbtack (own pro data) and Fixr (own cost data, corroborating the basic-slab band). This Old House's $4-$8 band and 30x30 total match Angi's exactly, so it is treated as corroboration, not an independent confirmation. Synthesized typical $5,400-$7,200 = honest overlap of the most-pay and average bands for a 900-square-foot slab (Angi $3,600-$7,200; HomeGuide 30x30 $5,400-$10,800; Thumbtack $3,155-$8,493; This Old House $3,600-$7,200); most-pay $5,500 = mean of the two published national averages (Angi $5,400; Thumbtack $5,686 — mean $5,543, rounded), labelled as such; per-square-foot $6-$8 = honest overlap (Angi $4-$8; HomeGuide $6-$12; Thumbtack $6-$9; This Old House $4-$8). Fixr's $4-$6 band is a basic-monolithic-garage-slab scope and is published as such, not merged. LABOUR DISAGREEMENT, published not averaged away: Angi prices labour at $2-$3 per square foot, HomeGuide at $3-$5 — the overlap is $3. REBAR DISAGREEMENT: Angi prices rebar at +$0.50-$1 per square foot, This Old House at $2-$3. No source publishes percentage shares for most of the job, so only materials (50-60%) and labour (40-50%) carry shares and there is no share bar on this page. Checked November 2026.. Sources last checked: October 2026 — This Old House, HomeGuide, Fixr, Angi, Thumbtack. How we calculate these costs

Cost by scope

Concrete Slab Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Small pad — shed foundation, walkway or parking pad$480 – $1,500The cheap end: a plain 4-inch slab of 100 to 200 square feet. Angi prices a shed foundation of 80 square feet at $480 and a 200-square-foot parking pad at $1,200; Thumbtack prices a 10x10 slab at $725 and a 12x12 at $1,044; This Old House matches Angi exactly on the shed ($480) and the parking pad ($1,200). HomeGuide prices a shed slab at $600–$4,800, the wide end of which is a larger shed — a small plain pad with no reinforcement and a broom finish is this tier
Standard 30-by-30-foot slab — most common$5,400 – $7,200The shared band itself: a 900-square-foot, 4-inch broom-finish slab — a two-car garage floor or a large patio. Angi's most-pay band ($3,600–$7,200), HomeGuide's 30x30 band ($5,400–$10,800), Thumbtack's average range ($3,155–$8,493) and This Old House's 30x30 band ($3,600–$7,200) all overlap here — this is the common residential job and the band this page is built on
Thickened-edge, reinforced or decorative slab — same 900 sq ft$7,200 – $17,000The expensive end: the same 900 square feet, but 6 inches or thicker, reinforced, or with a decorative finish. Stamped concrete runs $8–$19 per square foot in HomeGuide ($10–$18 in Angi, $10–$14 in This Old House), which is $7,200–$17,100 for 900 square feet; a reinforced 6-inch slab runs $8–$10 per square foot in HomeGuide, and Angi prices foundation-thickness slabs of 8 to 10 inches at $12–$18 per square foot. Fixr prices a monolithic garage slab up to $16 per square foot with heavier footings, or $14,400 for 900 square feet — inside this band. Elaborate stamped patterns run $18–$20 per square foot in This Old House, just above this band

Where the money goes

Part of the jobShareNote
Materials — concrete, gravel base, forms & reinforcement50–60% of totalConcrete, the gravel base, formwork and reinforcement together run $3–$7 per square foot in HomeGuide, and materials are 50–60% of the total job. Concrete itself runs about $110 per cubic yard in Angi ($113–$126 in This Old House, $150–$180 in Thumbtack, via Concrete Network) — one cubic yard covers about 81 square feet at 4 inches thick (This Old House), so a 900-square-foot slab needs roughly 11 cubic yards before waste. The gravel base underneath runs $1–$3 per square foot in HomeGuide.
Labour — forming, pouring, finishing40–50% of totalLabour is 40–50% of the total in HomeGuide, and one-third to one-half in Angi. The guides disagree on the per-square-foot rate: Angi prices labour at $2–$3 per square foot, HomeGuide at $3–$5 — the overlap is $3. Forming, pouring, screeding and finishing a slab is skilled, time-sensitive work: the concrete starts setting as soon as it is poured, which is why most of the labour cost is in the finishing crew, not the pour itself.
Site prep, excavation & gradingNo published shareLevelling the ground runs $0.40–$2.00 per square foot in HomeGuide, and the gravel base under the slab runs $1–$3 per square foot. A slab needs a flat, compacted base — digging, grading and compacting are priced on the excavation and yard grading guides, and a sloped or soft site costs more to prepare than flat, firm ground.
Reinforcement — rebar, wire mesh or fiberNo published shareThe guides disagree on rebar: Angi prices it at +$0.50–$1.00 per square foot, This Old House at $2–$3, while fiber mesh adds $2–$3 per square foot in Angi and wire mesh costs $0.35 per square foot in This Old House. Thicker edges add $1–$2 per square foot in This Old House. Reinforcement is what keeps a slab from cracking as the ground moves — a plain 4-inch shed pad can skip it, a driveway or garage floor should not.
Finish — broom, trowel, stamped, stained or polishedNo published shareA plain broom or smooth-trowel finish runs $1–$3 per square foot in Angi, or is included in the base price. Decorative finishes cost far more: exposed aggregate $7–$15, stamped $10–$18, stained $8–$15 and polished $3–$12 per square foot in Angi; HomeGuide prices stamped at $8–$19; This Old House prices stain or dye at +$3.50–$7.50, stamping at $10–$14 (elaborate patterns $18–$20) and epoxy or sealer at +$4.50 per square foot. The finish is the single biggest lever on the per-square-foot price after thickness.
Removal of old concrete + disposalNo published shareRemoving an old slab runs $3–$8 per square foot in HomeGuide, or $500–$1,800 per job in Thumbtack. Resurfacing an existing slab instead runs $3–$5 per square foot in Angi ($3–$7 in HomeGuide) — cheaper than removal and a new pour, but only where the old slab is sound.
Sealing + permitsNo published shareSealant runs $1.35–$2.50 per square foot in Angi, $1–$3 in HomeGuide, and This Old House prices epoxy or sealer at +$4.50 per square foot. Permits vary by city and no source publishes a national figure — check with your city before pouring, since a slab that needs a permit and does not have one can be ordered removed.
Estimator’s note: on a concrete slab installation, materials — concrete, gravel base, forms & reinforcement is usually where quotes swing most (50–60% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
Hand-trowelling the wet concrete — labour is 40–50% of the total in HomeGuide, and the finishing crew is the skilled part of the job: the concrete starts setting as soon as it is poured.
Hand-trowelling the wet concrete — labour is 40–50% of the total in HomeGuide, and the finishing crew is the skilled part of the job: the concrete starts setting as soon as it is poured.

What moves the price most

Size is the first driver: a slab is priced by the square foot, and the page's $6–$8 per square foot band is the honest overlap of Angi ($4–$8), HomeGuide ($6–$12), Thumbtack ($6–$9) and This Old House ($4–$8) — a 900-square-foot slab at $6–$8 per square foot is $5,400–$7,200, which is the typical band itself. Thickness is second: HomeGuide prices 2-inch slabs at $4–$6, 4-inch at $6–$8, 6-inch at $8–$10 and 8-inch at $10–$12 per square foot, and Angi prices foundation-thickness slabs of 8 to 10 inches at $12–$18 — four inches is the standard for a shed pad, walkway or patio, while driveways and garage floors usually need 5 to 6 inches. Reinforcement is third: fiber mesh adds $2–$3 per square foot in Angi, and rebar is where the guides disagree — Angi prices it at +$0.50–$1.00 per square foot, This Old House at $2–$3 — so get the reinforcement type and rate in writing. Finish is fourth: a plain broom or trowel finish is $1–$3 per square foot or included, while stamped concrete runs $8–$19 per square foot in HomeGuide and stained $8–$15 in Angi — the finish is the biggest lever on the per-square-foot price after thickness. Labour is fifth: Angi prices it at $2–$3 per square foot, HomeGuide at $3–$5, and the overlap is $3 — the guides disagree, so compare quotes on the crew size and the finish included, not on the headline rate. Region is sixth: Angi prices slabs from $5.35 per square foot in the mid-country to $8.50 on the coasts — California $7.70–$8.50, New York $6.70–$8.50, Texas $5.30–$5.90, Kentucky $5.20–$5.70. Site prep is seventh: levelling runs $0.40–$2.00 per square foot and the gravel base $1–$3 in HomeGuide, and a sloped or soft site costs more to prepare than flat, firm ground. What a slab price does NOT include: removal of an old slab ($3–$8 per square foot in HomeGuide, $500–$1,800 per job in Thumbtack), sealing ($1–$3 per square foot in HomeGuide) and permits, which vary by city with no national figure published. DIY fits only small pads: Angi says DIY saves $2–$3 per square foot in labour, but only a shed base or a short walkway is a realistic DIY job — a garage floor, driveway or foundation slab needs a crew, because the concrete starts setting as soon as it is poured and a bad pour is expensive to remove and pour again. Methodology: figures cross-checked across Angi (updated Oct 27, 2026), HomeGuide (updated Feb 3, 2026), Thumbtack (published Apr 10, 2026) and This Old House (updated Mar 17, 2026), read in full on 2026-11-17, with Fixr as labelled corroboration. Angi and HomeGuide sit in the same Angi Inc. data family and count as one confirmation; the three independent confirmations are the Angi family, Thumbtack (own pro data) and Fixr (own cost data, corroborating the basic-slab band). This Old House's $4–$8 band and 30x30 total match Angi's exactly, so it is treated as corroboration, not an independent confirmation. The labour disagreement (Angi $2–$3 against HomeGuide $3–$5 per square foot) and the rebar disagreement (Angi +$0.50–$1.00 against This Old House $2–$3) are published as disagreements, not averaged away. Related costs: concrete driveway, patio installation, foundation installation, stamped concrete installation, garage floor coating, concrete leveling, excavation and Remodel Cost Index.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A cured concrete surface — a slab lasts 30–50 years (HomeGuide) when it is poured, cured and sealed properly, and you can walk on it after 1–2 days, drive on it after 1–2 weeks, with full curing taking up to 28 days.
A cured concrete surface — a slab lasts 30–50 years (HomeGuide) when it is poured, cured and sealed properly, and you can walk on it after 1–2 days, drive on it after 1–2 weeks, with full curing taking up to 28 days.

Frequently asked questions

How much does a concrete slab cost?

A standard 30-by-30-foot slab (900 square feet) typically costs $5,400–$7,200 installed, with about $5,500 the figure most jobs land near — $5,500 is the mean of the two published national averages (Angi $5,400; Thumbtack $5,686), not a published average itself. A small shed pad can cost as little as $480, and a thickened-edge, reinforced or stamped slab the same size runs $7,200–$17,000.

How much does a concrete slab cost per square foot?

$6–$8 per square foot installed for a plain 4-inch broom-finish slab — the honest overlap of Angi's $4–$8, HomeGuide's $6–$12, Thumbtack's $6–$9 and This Old House's $4–$8. Thicker slabs cost more per foot: HomeGuide prices a 6-inch slab at $8–$10 and an 8-inch slab at $10–$12 per square foot, and decorative finishes push it higher still — stamped concrete runs $8–$19 per square foot in HomeGuide.

How much does a 20x20 concrete slab cost?

Angi prices a 20-by-20-foot slab (400 square feet) at $2,400 and Thumbtack at $2,900, while HomeGuide's $6–$12 per-square-foot band puts it at $2,400–$4,800. At this page's $6–$8 per-square-foot band, a 20x20 slab runs $2,400–$3,200 — the spread is the finish and the thickness, not the size.

How thick should a concrete slab be?

Four inches is the standard for a shed pad, walkway or patio. Driveways and garage floors usually need 5 to 6 inches, and a slab that carries a building — a home foundation — runs 8 to 10 inches in Angi, at $12–$18 per square foot. Thicker slabs use more concrete and cost more per foot: HomeGuide prices 2-inch at $4–$6, 4-inch at $6–$8, 6-inch at $8–$10 and 8-inch at $10–$12 per square foot.

How long does a concrete slab last, and when can I walk or drive on it?

A concrete slab lasts 30–50 years in HomeGuide (30–40 in This Old House) when it is poured, cured and sealed properly. You can usually walk on it after 1–2 days and drive on it after 1–2 weeks, but full curing takes up to 28 days (28–48 days in HomeGuide) — keep heavy loads off it until then, and seal it once it has cured.

Can I pour a concrete slab myself?

Only a small one. Angi says DIY saves $2–$3 per square foot in labour, but only a small pad — a shed base or a short walkway — is a realistic DIY job. A garage floor, driveway or foundation slab needs a crew: the concrete starts setting as soon as it is poured, so levelling, screeding and finishing have to happen fast, and a slab poured wrong cracks, settles or drains toward the house. This Old House warns the same — and a bad pour is expensive to remove ($3–$8 per square foot in HomeGuide) and pour again.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Concrete Slab Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

A yellow-and-blue bulldozer grading a dirt track through a rocky cut, with track-marked earth and rock piles around it

Site Preparation Cost

$1,300 – $4,000

Site preparation typically costs $1,300 – $4,000 for a standard residential lot, with about $3,800 the figure most jobs land near — $3,800 is Angi's published national average for site preparation, not a mean of averages. That works out to $2 – $3 per sq ft, the honest overlap of Angi's residential-lot rate ($1.50–$3.00 per sq ft) and Fixr's general site work ($2–$10 per sq ft). Site preparation is the bundle, not one trade: clearing, grading and excavation plus the survey, soil testing, permits and erosion control that come before the foundation goes in — each trade is priced on its own guide, and this page prices the job as a whole. A small shed pad can cost as little as $1,000, while a full acre or more of wooded, sloped ground runs $5,000–$20,000 and up. Wider all-in figures — $15,000–$50,000 including utility connections (True Built Home, via LegalClarity) and $20,000–$100,000 per acre for full land development (HomeGuide) — price a bigger scope than this page, and are published as such rather than merged.

A small wood-clad cabin with a metal roof behind flowering garden shrubs, rocks and grass under a blue sky

Backyard Office Construction Cost

$15,000 – $40,000

Backyard office construction typically costs $15,000 – $40,000 for a standard finished office of about 120–200 square feet, with about $25,000 the figure most jobs land near — $25,000 is the shared midpoint of the published bands (HomeGuide's $10,000–$40,000 band midpoints at $25,000, Tri-Cities' mid-range $15,000–$35,000 midpoints at $25,000, and Rivolty's entry tier starts at $25,000), not a published average itself. That works out to $120 – $250 per sq ft fully finished (Tri-Cities), against HomeGuide's $35–$75 per sq ft for a standard finish and $75–$150 for a full finish — the HomeGuide rates are structure and finish rates, not all-in project rates, and are published as such. A basic DIY shell finish can cost as little as $5,000, while a large custom site-built office runs $40,000–$75,000 and up. Rivolty's $65,000–$100,000+ premium band is a Bay Area figure (labour there runs 20–30% above the national average) and is published as such, not merged into the national typical. A guest house or ADU — plumbing, a kitchen and a bath — is a different, larger scope at $50,000–$150,000 in HomeGuide, and is published as the line this page stops at, not merged.

Fresh tree stumps in a cleared pine forest, cut trunks and brush between standing trees

Stump Grinding Cost

$140 – $400

The typical project is grinding one average yard stump — about 24 inches across — down 4 to 6 inches below grade and leaving the chips in the hole, at $2 – $6 per inch of diameter in HomeGuide. Small stumps, extra stumps at the same visit and oversize hardwood stumps are tiered separately below; full stump excavation and root removal are different work, priced on the tree-removal page and in the FAQs.

Living room with a lit brick fireplace, mantel and hearth, sofas around a coffee table

Chimney Sweeping Cost

$150 – $375

The typical project is a professional sweep of one wood-burning fireplace flue with a Level 1 inspection — brushes and a vacuum through the flue, the firebox and smoke shelf cleaned, and a written condition check. Gas fireplaces, second flues and Level 2 camera inspections are tiered separately below; repairs the sweep finds, like caps and liners, are priced as their own lines, never folded into the sweep.

Laundry room with a white washer and dryer pair under wooden cabinets

Dryer Vent Cleaning Cost

$100 – $185

The typical project is a professional cleaning of one residential dryer vent run — the dryer pulled out, the full duct brushed and vacuumed from the machine to the exterior hood, and airflow checked at the exit. Roof-exit vents, bird nests and vent rerouting are tiered separately below; a new vent installation is different work and is priced in the FAQs, not folded into a cleaning.

Chrome kitchen faucet dripping slowly into a stainless steel sink

Drain Cleaning Cost

$150 – $350

The typical project is a professional snaking of one clogged household drain — a kitchen sink, bathroom sink, tub or toilet — with the auger run to the clog, the line flushed and flow tested before the plumber leaves. Main-line stoppages and hydro jetting are tiered separately below; a full repipe or a sewer replacement is different work, priced on the plumbing-repipe page and in the FAQs, never folded into a cleaning.