Well Pump Installation cost at a glance
- Typical range: $2,500 – $5,000
- Most homeowners pay: around $3,500
Cross-checked against four published sources for this project. Sources used for this page: ABS Pipes, 'Well Pump Installation Cost (2026)', published Oct 18, 2026, updated Nov 2, 2026 — THE only source with an explicit new-install band: brand-new installation on a freshly drilled well $2,500–$5,000 or more (wiring, piping, pressure tank included); replacement $1,000–$3,500, most ~$2,000; submersible install $1,200–$3,500 (unit $500–$1,500); jet install $800–$2,000 (unit $300–$900); labour $500–$1,500 (3–6 hrs); drop pipe and wire $150–$600; pressure switch and fittings $50–$200; pressure tank $300–$900; electrical work $150–$500; permits/inspections $100–$500; drilling $5,000–$15,000+; ~100-ft well ~1/2 HP, ~400-ft well 2 HP+ (gap can exceed $800); emergency/after-hours +$200–$500; replacement time 3–6 hours. Angi, 'How Much Does Well Pump Replacement Cost? [2026 Data]', updated Aug 31, 2026 (1,339 verified projects) — REPLACEMENT figures: national average $1,897, most $973–$2,822; submersible installed $1,000–$2,500+, shallow jet $450–$1,500, deep-well jet $800–$2,200+, constant-pressure $1,300–$4,000+, solar $1,800–$6,500+; by depth under 25 ft $400–$3,000+, 25–150 ft $1,200–$5,500+, over 150 ft $2,000–$10,000+; labour $250–$1,000 per project, $45–$150/hour; new pipework/electrical add $250–$1,000 labour. HomeGuide, 'How Much Does a Well Pump Cost To Replace or Install? (2026)', published Aug 24, 2022, updated Aug 7, 2025 — REPLACEMENT figures: national average $1,800, average range $1,000–$2,500; submersible $1,000–$2,500, deep-well jet $500–$1,400, shallow jet $400–$1,000, constant-pressure $2,000–$5,000; plumbing labour $250–$800 (over $1,000 for difficult installs); electrician $50–$130/hour; pressure tank $500–$1,000 (pump page) vs $800–$1,500 (drilling page, full-system context); pressure switch $25–$100; pump lifespan 10–15 years; install 3–6 hours; states new installation costs MORE than replacement (no dollar figure). This Old House, 'Well Pump Cost and Installation Guide (2026)', published May 17, 2022, updated Mar 5, 2026 — REPLACEMENT figures: $900–$2,500 on average; unit spot-checked at The Home Depot $200–$500 (submersible $500); submersibles typically 200–300 ft or more; DIY not recommended for deep-well submersibles. Breakdown shares are derived from the worked example below. Checked November 2026.. Sources last checked: October 2026 — This Old House, HomeGuide, Angi, Home Depot. How we calculate these costs
Cost by scope

| Scope | Typical cost | What it includes |
|---|---|---|
| Budget — shallow-well jet pump | $800 – $1,500 | A shallow-well jet pump (well under 25 ft) on an existing well where the wiring and pressure tank are already in place and reusable — jet pump unit plus basic labour, no new tank, no new electrical run, no permits beyond the minimum. |
| Standard — submersible pump, new tank | $2,500 – $3,500 | The most-pay tier — the worked example below: a submersible pump (1/2–1 HP) for a residential well of about 100–200 ft, with a new pressure tank, pressure switch, drop pipe and wire, electrical connection from the panel, and permits. |
| Premium — deep well, constant pressure | $4,000 – $6,500+ | A deep well (300+ ft), a 1.5–2 HP submersible or constant-pressure/VFD system, a larger pressure tank, a long electrical run from the panel, possible drop-pipe replacement and water-quality testing. Open-ended above $6,500 for very deep wells — Angi's whole-project bands run $2,000–$10,000+ for wells over 150 ft. |
Where the money goes
| Part of the job | Share | Note |
|---|---|---|
| Submersible pump unit — 1 HP | 28% of total | $1,000 for the pump unit — a 1 HP submersible pump, inside ABS Pipes' $500–$1,500 band and the $1,000–$2,500 installed submersible bands from Angi and HomeGuide. Share derived from the worked example below. |
| Pressure tank — new | 17% of total | $600 for a new pressure tank — inside ABS Pipes' $300–$900 band and HomeGuide's $500–$1,000 band. HomeGuide's drilling page puts tanks at $800–$1,500 in a full-system context — see the factors note. Share derived from the worked example below. |
| Labour — install, 3–6 hours | 26% of total | $900 for installation labour — inside ABS Pipes' $500–$1,500 band and Angi's $250–$1,000 band. It sits ABOVE HomeGuide's typical $250–$800 plumbing-labour band (HomeGuide allows over $1,000 only for difficult installs) — the labour line follows ABS/Angi, not HomeGuide; see the factors note. Share derived from the worked example below. |
| Drop pipe, wire, switch + fittings | 14% of total | $500 for drop pipe, wire, pressure switch and fittings — inside ABS Pipes' combined $200–$800 band (drop pipe and wire $150–$600 plus switch and fittings $50–$200). This line merges two ABS lines; the combined band is stated, not invented. Share derived from the worked example below. |
| Electrical work — new circuit | 9% of total | $300 for electrical work — a new circuit and wiring from the panel, inside ABS Pipes' $150–$500 band. Share derived from the worked example below. |
| Permits + inspection | 6% of total | $200 for permits and inspection — inside ABS Pipes' $100–$500 band, the only published permit figure for a new pump install. Share derived from the worked example below. |

What moves the price most
Worked example — $3,500 most-pay install (1 HP submersible pump, residential well about 150 ft deep, new pressure tank, new wiring from the panel, permits included; drilling excluded): pump unit $1,000 (28%) + pressure tank $600 (17%) + labour $900 (26%) + drop pipe, wire, switch and fittings $500 (14%) + electrical work $300 (9%) + permits $200 (6%) = $3,500. Every line sits inside a published band from at least one source. Flags carried on the page: the $900 labour line sits above HomeGuide's typical $250–$800 plumbing-labour band and follows ABS Pipes ($500–$1,500) and Angi ($250–$1,000) instead — ABS is the newest source (November 2026) and its labour band is roughly double HomeGuide's typical band; the drop-pipe line merges two ABS lines (drop pipe and wire $150–$600; switch and fittings $50–$200) into one combined $200–$800 band; the most-pay $3,500 is the worked-example total, not a published average. Where sources disagree: the most-pay band for a pump job (replacement context) — Angi $973–$2,822 (average $1,897) vs HomeGuide $1,000–$2,500 (average $1,800) vs ABS Pipes $1,000–$3,500 (average ~$2,000) vs This Old House $900–$2,500 (no average); pressure tank — ABS $300–$900 vs HomeGuide $500–$1,000 (pump page) vs HomeGuide $800–$1,500 (drilling page, full-system context; HomeGuide disagrees with itself across its own two pages); pump unit alone — HomeGuide $150–$1,700 (all types) vs This Old House $200–$500 (a single-retailer spot check at The Home Depot, not an installed range) vs ABS submersible $500–$1,500, jet $300–$900; electrical work — Angi $50–$100 an hour vs HomeGuide $50–$130 an hour vs ABS flat $150–$500 for a new circuit vs HomeGuide $1,000–$3,000 for wiring in a complete new well system (a full-system number, not a pump-only number); deep-well jet depth limit — HomeGuide 50–100 ft vs ABS up to 150 ft vs This Old House "beyond 25 ft, sometimes more than 100 ft" (no agreed limit); Angi's depth bands are whole-project costs by well size, including pipework and wiring — under 25 ft $400–$3,000+, 25–150 ft $1,200–$5,500+, over 150 ft $2,000–$10,000+ — not pump-only prices. Only ABS gives a dollar band for a brand-new install ($2,500–$5,000+); HomeGuide states only that new installs cost more than replacements, with no figure. Methodology: figures cross-checked across Angi, HomeGuide, This Old House and ABS Pipes; ABS Pipes is the only source with an explicit new-install band and the page's typical range is its band; other sources' figures are replacement-context and are labelled as such. A first-time install costs more than a replacement because it needs more labour plus a tank, wiring and piping that a replacement usually reuses (HomeGuide; ABS Pipes). Related costs: well pump replacement, water well drilling, sump pump installation and water softener installation.
Costs in your city
Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

Frequently asked questions
How much does it cost to install a new well pump?
For a brand-new installation — pump, pressure tank, wiring, piping and permits, on a well that is already drilled — expect $2,500–$5,000 or more (ABS Pipes). Most homeowners pay around $3,500 for a standard submersible install. Drilling the well itself is separate ($5,000–$16,000; ABS Pipes; HomeGuide).
How long does well pump installation take?
A standard replacement takes 3–6 hours (ABS Pipes; HomeGuide). Angi's installation guide gives 2–10 hours depending on pump type and access. No source publishes a time figure specifically for a first-time install; a new install takes longer than a replacement because the tank, wiring and piping are added.
Is a submersible pump more expensive to install than a jet pump?
Yes. Submersible installation runs $1,200–$3,500 versus $800–$2,000 for a jet pump (ABS Pipes). Submersibles are more efficient, quieter and longer-lived, and are the only practical option for wells deeper than about 150 ft (ABS Pipes; This Old House). Jet pumps suit shallow wells under 25 ft (shallow jet) to 100–150 ft (deep-well jet, sources differ).
Does the quote usually include a pressure tank?
Not always. ABS Pipes notes many quotes cover only the pump and labour — ask explicitly whether the pressure tank, pressure switch and electrical work are included. A new tank costs $300–$900 (ABS Pipes) to $500–$1,000 (HomeGuide).
Can I install a well pump myself?
Not recommended for a submersible pump in a deep well: it needs a hoist rig, electrical work and experience, and mistakes can damage the well or create safety hazards (ABS Pipes; This Old House). DIY is possible only for shallow jet pumps (ABS Pipes). This Old House advises calling a professional to confirm the diagnosis before any removal work.
How long does a well pump last?
10–15 years with proper care (HomeGuide); submersible pumps typically last 15–25 years and jet pumps 10–15 years (ABS Pipes). Regular inspection every 1–2 years helps (HomeGuide, inspection $250–$550).






