Home › Cost Guides › Well Pump Replacement
Cost Guide

How Much Does a Well Pump Replacement Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$900 – $2,500
Most homeowners pay around $1,897 (Angi, Aug 2026) · A residential well pump replacement (pump + pull labor + pipework) runs $900–$2,500 installed for most homes — Angi’s 2026 national average is $1,897 across 1,339 verified projects (most paying $973–$2,822), This Old House puts the typical job at $900–$2,500 and LandClearingAndExcavation averages ~$1,900 across depths and pump types. Deep wells (300–400 ft) routinely run $2,800–$5,500+. Figures no source publishes: per-horsepower cost tables and a parts-vs-labor percentage split — omit those, never invent them.
typical
$900$2,500
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Technician adjusting a water pump indoors

Well Pump Replacement cost at a glance

  • Typical range: $900 – $2,500
  • Most homeowners pay: around $1,897 (Angi, Aug 2026)

Cross-checked against two published sources for this project. Sources used for this page: the Angi well pump replacement cost guide (updated August 2026), This Old House’s well pump cost and installation guide (March 2026), LandClearingAndExcavation.com’s 2026 well pump replacement cost data and American Home Shield’s water well pump replacement cost guide (February 2026). Sources last checked: October 2026 — This Old House, Angi. How we calculate these costs

Cost by scope

Well Pump Replacement cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Shallow well — jet pump (≤25 ft)$400 – $1,500Angi $450–$1,500 shallow jet; HomeGuide $400–$1,000 installed; LandClearingAndExcavation $800–$1,800 installed — the cheapest pump jobs
Deep-well jet pump (50–150 ft)$800 – $2,200+Angi $800–$2,200+ vs HomeGuide $500–$1,400 — a genuine disagreement; the honest overlap is $800–$1,400
Submersible pump — the common job$1,000 – $3,000Angi $1,000–$2,500+; HomeGuide $1,000–$2,500; LandClearingAndExcavation $1,500–$3,000 at 100–200 ft — ‘the most common job,’ averaging ~$1,900
Deep submersible (300–400 ft)$2,800 – $5,500+LandClearingAndExcavation’s installed band — each extra 100 ft of depth adds $500–$1,000 in drop pipe, wire and crew time

Where the money goes

Part of the jobShareNote
Pump unit$200 – $1,700Unit-only ranges: This Old House $200–$500 (Home Depot pricing), HomeGuide $150–$1,700, LandClearingAndExcavation $300–$1,500 — pump type and horsepower drive it; no source publishes per-HP tables
Labor — pull, set, test$250 – $1,000Angi $250–$1,000; HomeGuide $250–$800 (over $1,000 on difficult installs); pro rates $45–$150/hr — no source publishes a labor-vs-parts percentage split
Pipework and electrical$250 – $1,000+Angi: new pipework + wiring repairs add $250–$1,000 in labor; electrician rates $50–$130/hr (Angi, HomeGuide)
Pressure tank, switch, control box$25 – $1,000HomeGuide parts: pressure switch $25–$100, pressure tank $500–$1,000, pump motor $500–$1,000; LandClearingAndExcavation: control box $400–$900
Pipework and wiring add $250–$1,000 in labor (Angi) — fittings, drop pipe and the pressure switch are usually swapped while the pump is out.
Pipework and wiring add $250–$1,000 in labor (Angi) — fittings, drop pipe and the pressure switch are usually swapped while the pump is out.

What moves the price most

Well depth is the strongest price lever. Each extra 100 ft adds $500–$1,000 in drop pipe, wire and crew time (LandClearingAndExcavation), and Angi’s depth table runs from $400–$3,000+ under 25 ft to $2,000–$10,000+ past 150 ft. Pump type follows depth: shallow jet (Angi $450–$1,500) up to submersible (Angi $1,000–$2,500+). Horsepower and flow rate (GPM) move the unit price, though no source publishes per-HP bands. Labor rates ($45–$150/hr) vary by region, and deep or tight-access wells cost more to pull. Pipework and wiring condition add $250–$1,000 in labor when replaced. The pressure tank and switch are often found failed alongside the pump ($25–$1,000 in parts). Emergency or same-day service adds 25–50% (LandClearingAndExcavation). A like-for-like replacement costs less than a new install or a type upgrade (HomeGuide). Permits and inspections run $250–$550 (HomeGuide). On DIY: every source says pro — pumps can weigh 100+ lb and sit 25–400 ft down; hire a licensed pump installer.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
Diagnose cheap-first: a $25 pressure switch is ‘behind a lot of pumps that get declared dead’ (LandClearingAndExcavation) — rule it out before paying for a new pump.
Diagnose cheap-first: a $25 pressure switch is ‘behind a lot of pumps that get declared dead’ (LandClearingAndExcavation) — rule it out before paying for a new pump.

Frequently asked questions

How much does well pump replacement cost?

Most replacements run $900–$2,500 installed. Angi’s 2026 national average is $1,897 across 1,339 verified projects (most paying $973–$2,822); LandClearingAndExcavation averages ~$1,900. Deep wells (300–400 ft) routinely run $2,800–$5,500+.

How much does a well pump cost by type?

Shallow-well jet $400–$1,500, deep-well jet $800–$2,200+ (Angi; HomeGuide says $500–$1,400 — genuine disagreement, overlap $800–$1,400), submersible $1,000–$2,500+ and constant-pressure $1,300–$4,000+ (Angi).

How much is labor to replace a well pump?

Replacement labor runs $250–$1,000 (Angi) or $250–$800 (HomeGuide, over $1,000 on difficult installs) at $45–$150/hr. New pipework and wiring add another $250–$1,000 in labor.

Should I repair or replace my well pump?

Diagnose cheap-first (LandClearingAndExcavation): pressure switch ~$25 part / $75–$150 labor, pressure tank from ~$200, control box $400–$900, diagnostic service call $250–$500 (usually credited). If the pump is already pulled and is ~12 years old, replace it while the labor is paid. Angi: ‘consider repairing versus replacing, if the cost makes sense.’

How long does a well pump last?

10–15 years with proper care (HomeGuide, LandClearingAndExcavation); American Home Shield cites an average of 14 years. The well itself lasts 40+ years. A replacement takes about 3–6 hours (HomeGuide).

Can I replace a well pump myself?

No source recommends it. Pumps can weigh 100+ lb and sit 25–400 ft down the well, needing hoists and down-hole tools (Angi, This Old House). A licensed pump installer also handles the permits and diagnoses switch/tank issues before you pay for a pump.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Well Pump Replacement cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

White panel radiator on a brick wall

Boiler Replacement Cost

$3,200 – $9,000

A residential boiler replacement (equipment + labor) averages $6,100 — HomeGuide’s national figure (updated December 2025), with typical full swaps landing at $3,200–$9,000. This Old House puts equipment + labor at $4,500–$10,000; Modernize (August 2026) averages $6,500–$11,500 — its bands skew toward full installs rather than simple swaps. Gas is the most common fuel; high-efficiency/condensing models cost a clear premium. Figures no source publishes: a distinct national ‘most-pay’ figure, per-sq-ft installed pricing, and a 50% repair-vs-replace rule.

Home inspector examining a crawl space entrance

Crawl Space Encapsulation Cost

$5,000 – $15,000

Professional crawl space encapsulation averages $5,500 — Angi and This Old House (both 2026) publish the same average, with typical totals of $5,000–$15,000 (Modernize agrees, September 2026). Basic work runs $2–$4/sq ft (Angi) to $3–$7/sq ft (This Old House); extensive moisture-problem jobs reach $10/sq ft. Labor is 50–70% of the total; materials are 30–50% (Angi, This Old House).

Exposed sheet-metal air ducts and a supply register on a dark ceiling

Ductwork Replacement Cost

$1,400 – $5,600

Replacing a home’s air ducts averages $3,500 — HomeGuide’s national figure across 399 member projects (updated December 2025), with the typical range at $1,400–$5,600 by home size. This Old House (2026, Homewyse data) prices it at $16–$19 per linear foot — about $3,100–$3,700 for an average 200-foot system — and CostHelper (2026) agrees with HomeGuide’s installed band at $35–$55 per foot. No source publishes a labor-vs-materials percentage split; HomeGuide’s average is the only published national figure.

Hand adjusting a modern black smart thermostat with a Wi-Fi icon on the wall

Smart Thermostat Installation Cost

$200 – $500

A smart thermostat installed by a pro averages $300 — Fixr’s national figure (updated January 2025) for a C-wire install plus an auto-schedule smart thermostat with a two-year warranty. HomeGuide (August 2025) puts the average smart install at $225–$400; Angi (July 2026) gives the widest band, $175 to over $1,000, with the high end reserved for relocations, new wiring and multi-unit jobs. No source publishes a labor-vs-device percentage split; Fixr’s average is the only smart-only national figure.

Two workers inspecting a brick chimney with clay flue tiles and a rain cap on a rooftop

Chimney Liner Replacement Cost

$1,500 – $5,000

A standard chimney reline averages $2,500 — Angi’s national figure (updated September 2026), with typical pro jobs landing at $1,500–$5,000. HomeGuide (February 2026) averages relining at $1,200–$4,600; Flue-Pipes’ 2026 guide prices a professional stainless reline at $1,500–$3,800, with complex jobs — tall chimneys, difficult access, cast-in-place liners — reaching $7,000 or more. Angi is the only source publishing a national average; Flue-Pipes’ labor share (40–60% of the pro price) is the only published percentage.

Technician repairing electrical equipment on a workbench, motor and wiring in hand

Furnace Repair Cost

$350 – $505

A typical furnace repair lands at $350–$505 — the honest overlap of the three published typical ranges: HomeAdvisor (Angi) $133–$505, Fixr $150–$600 and Modernize $350–$900. Published averages disagree more than the ranges do: $318 (HomeAdvisor), $350–$400 (Fixr) and around $600 (Modernize, whose average pulls in major repairs). $350 is published here as the most-pay figure because it sits inside Fixr’s average band and just above HomeAdvisor’s; it is not a cross-source average. Major repairs run to $2,000+ and heat-exchanger replacement to $3,500.