Home › Cost Guides › Mini-Split Installation
Cost Guide

How Much Does a Mini-Split Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$2,000 – $8,000
Most homeowners pay around $3,000 (Angi) – $8,500 (Modernize) · A professionally installed single-zone system — Angi ($2,000–$5,000 typical, ~$3,000 average), Modernize ($3,000–$8,000 installed) and USA Today ($2,000–$7,000 per zone) overlap at $2,000–$8,000; no single national average exists — the sources genuinely disagree ($3,000 vs $6,357 vs $8,500)
typical
$2,000$8,000
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Clean wall-mounted indoor mini-split air conditioning unit

Mini-Split Installation cost at a glance

  • Typical range: $2,000 – $8,000
  • Most homeowners pay: around $3,000 (Angi) – $8,500 (Modernize)

Cross-checked against three published sources for this project. Sources used for this page: the Angi mini-split installation cost guide (April 2026), Modernize's 2026 ductless heat pump cost guide (updated August 2026), Fixr's ductless AC installation cost data (January 2025) and USA Today's June 2026 mini-split cost reporting (ARS installer figures). Sources last checked: October 2026 — Modernize, Fixr, Angi. How we calculate these costs

Cost by scope

Mini-Split Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Single zone — one indoor head$2,000 – $8,000The corroborated band — Angi $500–$5,000 (table) to $2,000–$8,800 (prose), Modernize $3,000–$8,000, USA Today $2,000–$7,000; a 12,000 BTU unit averages about $3,000 (Angi)
Two zones$4,000 – $14,000Per-source figures, not merged — Angi $1,400–$7,700, Modernize $6,500–$12,000, USA Today $4,000–$14,000
Three to four zones$6,000 – $28,000Angi: 3-zone $1,800–$9,100, 4-zone $2,600–$10,700; Modernize: $8,000–$14,000 and $9,000–$15,000; USA Today (ARS): $6,000–$21,000 and $8,000–$28,000 — the widest published bands
Five or more zones — whole home$12,000 – $20,000+Modernize’s whole-home band; Angi’s 5-zone table runs $4,400–$12,000 ($4,800–$18,000 in its prose) — Angi’s own page disagrees with itself here, recorded as published

Where the money goes

Part of the jobShareNote
Equipment — outdoor unit plus indoor head(s)$1,000 – $5,500+Angi’s parts band: outdoor unit $1,000–$5,500, indoor units $400–$1,800 each; brand tier moves it — budget MRCOOL/Gree at the bottom, premium Mitsubishi/Daikin at the top
HVAC labor$300 – $3,000Angi: $300–$1,500 alone, $300–$2,000 single-zone, $700–$3,000 multi-zone; Fixr’s hourly rates run $86–$157 — no source publishes a labor-vs-equipment percentage split
Electrical — dedicated circuit$250+Angi’s dedicated-circuit figure, plus $50–$100/hr for the electrician; panel upgrades add more
Permits and old-unit removal$250 – $550Permits $250–$400 (Angi); removing an old AC runs $80–$150
Extras — lines, mounts, pumps$40 – $560Refrigerant lines ~$5/ft (Angi), wall brackets $40–$100, condensate pumps $120–$280, drain-pan heaters $140–$560
The outdoor half of the system — the condenser runs $1,000–$5,500 in Angi’s parts band, and HVAC labor adds $300–$3,000 depending on zone count.
The outdoor half of the system — the condenser runs $1,000–$5,500 in Angi’s parts band, and HVAC labor adds $300–$3,000 depending on zone count.

What moves the price most

Zone count is the price lever. Each added indoor head needs equipment, line sets and labor — single-zone lands at $2,000–$8,000 while 5+ zone whole-home designs run $12,000–$20,000+ (Modernize). System size (BTU) scales with the space: a 12,000 BTU unit averages about $3,000 installed while 36,000 BTU runs $1,800–$6,000 (Angi). Brand tier is consistent across sources — budget MRCOOL and Gree at the bottom, mid-tier LG/Panasonic/Rheem/Fujitsu in the middle, premium Mitsubishi and Daikin at the top. Efficiency (SEER) costs more upfront and less to run; rebates and tax credits can offset it. Mounting style matters — wall units are cheapest, ceiling cassettes and floor consoles cost more (Angi: ceiling-mounted $1,200–$12,000). Line-set length (distance between indoor and outdoor units), electrical work (dedicated circuit $250; panel upgrades), permits ($250–$400) and second-story or complex routing all push the labor line. On DIY: Fixr says a single-zone may be DIY-able, but Modernize calls installation a pro job and Bob Vila notes many states require certified technicians for the refrigerant — and labor, per Bob Vila, ‘isn’t a major part of the overall cost’ anyway. Related costs: heat pump installation, HVAC replacement, air conditioner installation and electrical panel upgrade (for the dedicated circuit and any panel work); compare every project in the Remodel Cost Index.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
No ductwork needed — that’s the whole point; but line-set length, a $250 dedicated circuit and $250–$400 in permits still sit on the invoice (Angi).
No ductwork needed — that’s the whole point; but line-set length, a $250 dedicated circuit and $250–$400 in permits still sit on the invoice (Angi).

Frequently asked questions

How much does mini-split installation cost?

A single zone runs $2,000–$8,000 installed — the honest overlap of Angi, Modernize and USA Today (June 2026). There is no single national average: Angi says ~$3,000, Fixr $6,357, Modernize $8,500 — different scopes, presented per source.

How much does it cost per zone?

USA Today (via ARS) puts it at $2,000–$7,000 per zone installed; Modernize’s installed bands run $3,000–$8,000 for one zone up to $12,000–$20,000+ for five or more.

Which mini-split brand is cheapest?

The hierarchy is consistent across sources: budget MRCOOL ($700–$5,900, Angi) and Gree ($1,700–$3,200 equipment, Modernize); mid-tier LG, Panasonic, Rheem, Fujitsu; premium Mitsubishi and Daikin ‘tend to cost more’ (Fixr).

How much does the electrical work cost?

A dedicated circuit runs about $250 (Angi) with electricians at $50–$100/hr (Angi) or $101–$183/hr (Fixr); panel upgrades cost more.

Can I install a mini-split myself?

Maybe a single-zone unit (Fixr), but Modernize calls installation a pro job — vacuum and leak testing, permits and refrigerant handling, which many states restrict to certified technicians (Bob Vila). Labor ‘isn’t a major part of the overall cost’ (Bob Vila), so DIY saves less than it looks.

What size mini-split do I need?

Size by BTU for the space: Angi’s installed bands run from $450–$1,600 for 6,000 BTU to $3,000–$8,000 for 42,000 BTU, with the common 12,000 BTU unit averaging about $3,000.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Mini-Split Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Technician adjusting a water pump indoors

Well Pump Replacement Cost

$900 – $2,500

A residential well pump replacement (pump + pull labor + pipework) runs $900–$2,500 installed for most homes — Angi’s 2026 national average is $1,897 across 1,339 verified projects (most paying $973–$2,822), This Old House puts the typical job at $900–$2,500 and LandClearingAndExcavation averages ~$1,900 across depths and pump types. Deep wells (300–400 ft) routinely run $2,800–$5,500+. Figures no source publishes: per-horsepower cost tables and a parts-vs-labor percentage split — omit those, never invent them.

White panel radiator on a brick wall

Boiler Replacement Cost

$3,200 – $9,000

A residential boiler replacement (equipment + labor) averages $6,100 — HomeGuide’s national figure (updated December 2025), with typical full swaps landing at $3,200–$9,000. This Old House puts equipment + labor at $4,500–$10,000; Modernize (August 2026) averages $6,500–$11,500 — its bands skew toward full installs rather than simple swaps. Gas is the most common fuel; high-efficiency/condensing models cost a clear premium. Figures no source publishes: a distinct national ‘most-pay’ figure, per-sq-ft installed pricing, and a 50% repair-vs-replace rule.

Home inspector examining a crawl space entrance

Crawl Space Encapsulation Cost

$5,000 – $15,000

Professional crawl space encapsulation averages $5,500 — Angi and This Old House (both 2026) publish the same average, with typical totals of $5,000–$15,000 (Modernize agrees, September 2026). Basic work runs $2–$4/sq ft (Angi) to $3–$7/sq ft (This Old House); extensive moisture-problem jobs reach $10/sq ft. Labor is 50–70% of the total; materials are 30–50% (Angi, This Old House).

Exposed sheet-metal air ducts and a supply register on a dark ceiling

Ductwork Replacement Cost

$1,400 – $5,600

Replacing a home’s air ducts averages $3,500 — HomeGuide’s national figure across 399 member projects (updated December 2025), with the typical range at $1,400–$5,600 by home size. This Old House (2026, Homewyse data) prices it at $16–$19 per linear foot — about $3,100–$3,700 for an average 200-foot system — and CostHelper (2026) agrees with HomeGuide’s installed band at $35–$55 per foot. No source publishes a labor-vs-materials percentage split; HomeGuide’s average is the only published national figure.

Hand adjusting a modern black smart thermostat with a Wi-Fi icon on the wall

Smart Thermostat Installation Cost

$200 – $500

A smart thermostat installed by a pro averages $300 — Fixr’s national figure (updated January 2025) for a C-wire install plus an auto-schedule smart thermostat with a two-year warranty. HomeGuide (August 2025) puts the average smart install at $225–$400; Angi (July 2026) gives the widest band, $175 to over $1,000, with the high end reserved for relocations, new wiring and multi-unit jobs. No source publishes a labor-vs-device percentage split; Fixr’s average is the only smart-only national figure.

Two workers inspecting a brick chimney with clay flue tiles and a rain cap on a rooftop

Chimney Liner Replacement Cost

$1,500 – $5,000

A standard chimney reline averages $2,500 — Angi’s national figure (updated September 2026), with typical pro jobs landing at $1,500–$5,000. HomeGuide (February 2026) averages relining at $1,200–$4,600; Flue-Pipes’ 2026 guide prices a professional stainless reline at $1,500–$3,800, with complex jobs — tall chimneys, difficult access, cast-in-place liners — reaching $7,000 or more. Angi is the only source publishing a national average; Flue-Pipes’ labor share (40–60% of the pro price) is the only published percentage.