Home › Cost Guides › Air Conditioner Installation
Cost Guide

How Much Does an Air Conditioner Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$5,800 – $7,900
Most homeowners pay around $5,900 · A central air conditioner installation typically costs $5,800 – $7,900, with about $5,900 the most-pay figure — Angi puts a new central AC system at $5,900 on average with installation at $1,500–$4,000, HomeGuide's standard-efficiency replacement runs $5,000–$8,300, and Fixr's installed range runs $5,800–$14,400 because it includes jobs with new ductwork. The $5,800–$7,900 band is the overlap for a standard system on existing ducts: a like-for-like change-out is the cheap end, while a larger or higher-efficiency unit with duct modifications is the expensive end.
typical
$5,800$7,900
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Grey outdoor air conditioner condenser on a concrete pad beside a house

Air Conditioner Installation cost at a glance

  • Typical range: $5,800 – $7,900
  • Most homeowners pay: around $5,900

Cross-checked against three published sources for this project. Sources used for this page: Angi's central air guides (new central AC system average $5,900, installation $1,500–$4,000, install band $3,900–$7,900 for homes with ducts, ductwork $3,000–$7,500 per 300 linear feet), HomeGuide's AC replacement cost guide (standard $5,000–$8,300, mid-range $8,300–$12,500, high-end $12,500–$14,000+, tonnage table from 1.5-ton $4,700–$6,500 to 5-ton $7,000–$9,500+ installed, SEER table, permits $100–$250 replacement and $250–$1,500 new with ducts, duct sealing $300–$1,500, duct replacement $1,400–$5,600+, 4 hours–3 days) and Fixr's central air installation cost guide (average range $5,800–$14,400, most-pay $8,750 for a 3-ton 16 SEER unit with new ducts in a 2,000 sq ft home, low $3,750 change-out, high $18,000, $2.90–$7.20 per sq ft, tonnage installed table, split unit $3,800–$7,700, packaged $4,000–$8,500, packaged HVAC $9,200–$10,800, labor $1,250–$3,000 on existing ducts plus $965–$2,325 for new ducts, retrofit ducts $3,600–$9,500). Sources last checked: October 2026 — HomeGuide, Fixr, Angi. How we calculate these costs

Cost by scope

Air Conditioner Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Basic change-out on existing ducts$3,750 – $5,800The cheap end: Fixr's low of $3,750 for a change-out of a 3-ton 14 SEER unit on existing ducts, up to the typical band's floor
Standard install — the typical band$5,800 – $7,900The shared overlap itself: Angi's $3,900–$7,900 install band, HomeGuide's $5,000–$8,300 standard replacement and Fixr's $5,800–$14,400 installed range meeting here for a standard system on existing ducts
High-efficiency or new-duct install$7,900 – $18,000The expensive end: HomeGuide's high-end systems at $12,500–$14,000+, Fixr's packaged HVAC totals at $11,200–$15,800, and Fixr's high of $18,000 for a 3-ton 21 SEER unit with 300 feet of new ducts

Where the money goes

Part of the jobShareNote
Central AC install, Angi$3,900 – $7,900Angi's install band for a new central air conditioner in a home that already has ducts
New central AC system average, Angi$5,900Angi's average for a new central AC system, with installation at $1,500–$4,000 depending on the home's setup
Installation labor, Angi$1,500 – $4,000Angi's installation-cost band for a new central air system
Standard-efficiency replacement, HomeGuide$5,000 – $8,300HomeGuide's standard-efficiency replacement band for a 2,000 sq ft home, excluding ductwork modifications
Mid-range system, HomeGuide$8,300 – $12,500HomeGuide's mid-range band: two-stage cooling with enhanced features and efficiency
High-efficiency system, HomeGuide$12,500 – $14,000+HomeGuide's high-end band: variable-speed systems with premium features and maximum efficiency
Installed range including duct jobs, Fixr$5,800 – $14,400Fixr's national average range for installing central AC, covering change-outs through new-duct installations
Most-pay Fixr job$8,750Fixr's most-pay figure: a new 3-ton split system at 16 SEER with new ductwork in a 2,000 sq ft home
Low change-out, Fixr$3,750Fixr's low: a change-out of a 3-ton 14 SEER unit using existing ducts
High new install, Fixr$18,000Fixr's high: a new 3-ton 21 SEER unit with 300 feet of new ducts and customizations
Per square foot, Fixr$2.90 – $7.20Fixr's per-sq-ft band for installing central air, depending on size, efficiency and ducts
1.5-ton installed, Fixr$3,650 – $6,250Fixr's installed band for a 1.5-ton unit (18,000 BTU), materials $2,400–$4,250
2-ton installed, Fixr$4,250 – $7,500Fixr's installed band for a 2-ton unit (24,000 BTU), materials $3,000–$5,500
3-ton installed, Fixr$5,000 – $9,150Fixr's installed band for a 3-ton unit (36,000 BTU), materials $3,800–$7,150
4-ton installed, Fixr$6,950 – $11,600Fixr's installed band for a 4-ton unit (48,000 BTU), materials $5,750–$9,600
5-ton installed, Fixr$7,800 – $14,000Fixr's installed band for a 5-ton unit (60,000 BTU), materials $6,600–$12,000
Split system unit only, Fixr$3,800 – $7,700Fixr's unit-only band for a split system, the most common central AC type
Packaged AC unit only, Fixr$4,000 – $8,500Fixr's unit-only band for a packaged AC system, one outdoor cabinet
Packaged HVAC unit only, Fixr$9,200 – $10,800Fixr's unit-only band for a packaged system combining furnace and AC
14 SEER unit only, Fixr$1,725 – $3,600Fixr's unit-only band for a 14 SEER / 13.4 SEER2 3-ton unit, the northern minimum
16 SEER unit only, Fixr$2,875 – $6,000Fixr's unit-only band for a 16 SEER / 15.3 SEER2 3-ton unit, the first high-efficiency step
21 SEER unit only, Fixr$6,325 – $10,800Fixr's unit-only band for a 21 SEER / 20 SEER2 3-ton unit, the highest recommended residential rating
Labor on existing ducts, Fixr$1,250 – $3,000Fixr's labor band for installing the AC with lines and pad on existing ductwork
New-duct labor, Fixr$965 – $2,325Fixr's added labor band for installing new ducts, on top of the AC labor
Total labor, full AC + ducts, Fixr$2,215 – $5,325Fixr's total labor band for a full AC and duct installation out of its $8,750 total
Split system total, Fixr$5,050 – $10,700Fixr's total band for a split system, labor $1,250–$3,000
Packaged AC total, Fixr$5,000 – $11,000Fixr's total band for a packaged AC unit, labor $1,000–$2,500
Packaged HVAC total, Fixr$11,200 – $15,800Fixr's total band for a packaged HVAC unit, labor $2,000–$5,000
New ductwork retrofit, Fixr$3,600 – $9,500Fixr's labor-and-material band for new ductwork in a retrofit, on top of the $5,050–$10,700 unit and installation
Retrofit total, 3-ton with ducts, Fixr$8,650 – $20,200Fixr's total for a 3-ton unit with ducts in a 2,000 sq ft home without existing ductwork
Ductwork without AC, Angi$3,000 – $7,500Angi's band for adding ductwork per 300 linear feet in a home without ducts
Replacement permit, HomeGuide$100 – $250HomeGuide's permit band for an AC replacement
New-install permit with ducts, HomeGuide$250 – $1,500HomeGuide's permit band for a new AC installation with ductwork
Duct sealing and repairs, HomeGuide$300 – $1,500HomeGuide's band for minor duct sealing and repairs, often improving efficiency significantly
Ductwork replacement, HomeGuide$1,400 – $5,600+HomeGuide's band where some or all ducts are beyond repair
Install time, HomeGuide4 hours – 3 daysHomeGuide's time band: outdoor unit only 4–8 hours, both units 8–14 hours, full system with ductwork 2–3 days
Lifespan, HomeGuide / Fixr15 – 20 yearsHomeGuide's lifespan for a new AC system; Fixr puts most central units at 15–20 years with regular maintenance
A technician working on a wall-mounted outdoor unit with manifold gauges in view: the gauges and line work are part of the $1,250–$3,000 labor band for installing on existing ducts (Fixr) — this is a wall-mounted unit, not the ground-level central condenser in the hero shot
A technician working on a wall-mounted outdoor unit with manifold gauges in view: the gauges and line work are part of the $1,250–$3,000 labor band for installing on existing ducts (Fixr) — this is a wall-mounted unit, not the ground-level central condenser in the hero shot

What moves the price most

Size (tonnage) is the first driver (Fixr, HomeGuide): a 1.5-ton unit installs at $3,650–$6,250 (Fixr) against a 3-ton at $5,000–$9,150 and a 5-ton at $7,800–$14,000, and HomeGuide's home-size table runs from $4,500–$7,000 for a 1,000 sq ft home to $10,000–$16,000+ for 3,000 sq ft. Efficiency (SEER) is second: Fixr's 3-ton unit-only prices run from $1,725–$3,600 at 14 SEER to $6,325–$10,800 at 21 SEER, and HomeGuide's installed bands run from $5,300–$7,900 at 13–14 SEER to $11,400–$17,300+ at 22–26 SEER. Ductwork is third and often the largest swing: a change-out on existing ducts is Fixr's $3,750 low, while new ducts add $965–$2,325 in labor alone and a full retrofit totals $8,650–$20,200. System type closes the bill: a split system totals $5,050–$10,700 (Fixr) against a packaged AC at $5,000–$11,000 and a packaged HVAC unit at $11,200–$15,800.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A homeowner adjusting a wall thermostat: the thermostat and controls are the part of the system you touch every day, and a new thermostat is often bundled into the $5,800–$7,900 typical band rather than priced separately
A homeowner adjusting a wall thermostat: the thermostat and controls are the part of the system you touch every day, and a new thermostat is often bundled into the $5,800–$7,900 typical band rather than priced separately

Frequently asked questions

How much does air conditioner installation cost?

Typically $5,800–$7,900, with about $5,900 the most-pay figure. Angi puts a new central AC system at $5,900 on average, HomeGuide's standard-efficiency replacement runs $5,000–$8,300, and Fixr's $5,800–$14,400 range is wider because it includes jobs with new ductwork — the $5,800–$7,900 band is the overlap for a standard system on existing ducts.

What size air conditioner do I need?

One ton of cooling equals 12,000 BTU and cools roughly 500–600 square feet (HomeGuide), but layout, ceiling height, insulation, climate and sun exposure all move the answer — a 2,000 sq ft home takes 3.5–4.5 tons in HomeGuide's table, and an oversized unit short-cycles while an undersized one runs constantly without cooling the home.

Is a higher SEER rating worth the extra cost?

It depends on climate and use (Fixr, HomeGuide): a 14 SEER 3-ton unit runs $1,725–$3,600 unit-only against $6,325–$10,800 at 21 SEER (Fixr), and HomeGuide's installed bands run from $5,300–$7,900 at 13–14 SEER to $9,100–$12,200 at 19–21 SEER — in hot climates with heavy use the efficient unit pays back, in mild climates it may not.

How much extra does new ductwork add?

A lot: Fixr adds $965–$2,325 in labor for new ducts on top of $1,250–$3,000 for the AC itself, puts a full retrofit at $3,600–$9,500 for ducts alone, and totals a 3-ton retrofit at $8,650–$20,200 — while Angi prices adding ductwork at $3,000–$7,500 per 300 linear feet and HomeGuide prices duct replacement at $1,400–$5,600+.

How long does air conditioner installation take?

4 hours to 3 days (HomeGuide): replacing the outdoor unit only takes 4–8 hours, both indoor and outdoor units 8–14 hours, and a complete system with ductwork modifications 2–3 days — weather and permit requirements can extend it.

How long will a new air conditioner last?

15–20 years on average (HomeGuide, Fixr), depending on installation quality, maintenance frequency, usage and equipment quality — and new units run 20%–40% more efficiently than 10-year-old models (HomeGuide).

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Air Conditioner Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Metal outdoor faucet on a stone wall with green leaves

Outdoor Faucet Installation Cost

$150 – $500

An outdoor faucet installation typically costs $150 – $500, with about $325 the most-pay figure — LawnLove's typical range with a $325 median, HomeGuide's hose bib replacement at $150–$350, and Angi's replacement band at $100–$300 for a standard swap, with a brand-new faucet on a new water line running $100–$4,000 in Angi's guide. A like-for-like swap on an existing line is the cheap end; a frost-free model on a new line, far from the house supply, is the expensive end.

Two people lowering a folding metal attic ladder from a ceiling hatch

Attic Ladder Installation Cost

$400 – $1,000

An attic ladder installation typically costs $400 – $1,000, with about $500 the most-pay figure — Angi puts most homeowners at around $500 or more for labor and materials with installation at $300–$1,000, HomeGuide's basic replacement at $350–$1,000, and ThePricer's standard replacement or straightforward new opening at $400–$1,000. A like-for-like swap in an existing opening is the cheap end; a new opening with framing, or a high-ceiling or heavy-duty unit, is the expensive end.

Modern white house with large panes of glass across two floors and glass balcony rails

Window Glass Replacement Cost

$300 – $650

Replacing the glass in one standard window typically costs $300 – $650, with about $375 the most-pay figure — HomeGuide's average range is $300–$650 with a $475 national average, Fixr's national average is $375 inside a $300–$880 range, and Angi's average is lower at $285 because its project mix skews toward standard double-pane units, where most homeowners pay $181–$414. The $300–$650 band is the honest middle for a standard installed job: a single pane is cheaper, and a large, triple-pane or specialty window is dearer.

Room with a flooded tiled floor reflecting a window, and damp staining on the wall

Water Damage Restoration Cost

$1,400 – $6,400

Water damage restoration typically costs $1,400 – $6,400, with about $3,900 the most-pay figure — Angi puts the average at $3,868 with most homeowners paying $1,383–$6,369, Modernize puts the average near $3,900 on a $1,300–$6,500 band, and HomeGuide prices extraction alone at $4–$12 per square foot by water category. The $3,900 most-pay figure sits where Angi's and Modernize's averages meet; a small clean-water job lands well below it and black-water or whole-home flooding lands far above it.

A leaking outdoor water pipe spraying water

Leak Detection Cost

$150 – $400

Professional leak detection typically costs $150 – $400 for a standard hidden-leak visit, with about $300 the figure most visits land near — Angi prices detection at $100–$500, and HomeGuide prices a plumber's leak detection test at $100–$400. This guide prices finding the leak only — diagnosis, location and a written report — not the repair, which is quoted once the leak is located.

Bundled copper pipes stacked in a yard

Slab Leak Repair Cost

$630 – $4,400

A confirmed leak in a water line under a concrete slab foundation, located and repaired — detection included in Angi's average, floor and water-damage restoration billed separately