Home › Cost Guides › Ductwork Replacement
Cost Guide

How Much Does a Ductwork Replacement Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$1,400 – $5,600
Most homeowners pay around $3,500 (HomeGuide) · Replacing a home’s air ducts averages $3,500 — HomeGuide’s national figure across 399 member projects (updated December 2025), with the typical range at $1,400–$5,600 by home size. This Old House (2026, Homewyse data) prices it at $16–$19 per linear foot — about $3,100–$3,700 for an average 200-foot system — and CostHelper (2026) agrees with HomeGuide’s installed band at $35–$55 per foot. No source publishes a labor-vs-materials percentage split; HomeGuide’s average is the only published national figure.
typical
$1,400$5,600
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Exposed sheet-metal air ducts and a supply register on a dark ceiling

Ductwork Replacement cost at a glance

  • Typical range: $1,400 – $5,600
  • Most homeowners pay: around $3,500 (HomeGuide)

Cross-checked against four published sources for this project. Sources used for this page: HomeGuide's ductwork replacement cost guide (updated December 2025), This Old House's air duct replacement cost guide (2026, Homewyse data) and CostHelper's 2026 cost of ductwork. Sources last checked: October 2026 — This Old House, HomeGuide, Homewyse, CostHelper. How we calculate these costs

Cost by scope

Ductwork Replacement cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Small or partial — mobile homes, short runs$1,000 – $3,400HomeGuide: mobile home $1,000–$3,300; 1,000–1,500 sq ft homes $1,400–$3,400 — the cheapest replacements
Mid-size, accessible — basement or attic$1,800 – $5,600HomeGuide: basement $1,800–$3,100 (cheapest because ducts are easy to reach); attic $2,200–$5,600; 2,000–2,500 sq ft $2,800–$5,600
Difficult access or large home$3,000 – $9,000HomeGuide: crawl space $3,000–$7,300; 3,500–4,000 sq ft $4,900–$9,000; This Old House: 400–500 ft of ductwork $6,200–$9,300
New ducts where none existed$2,400 – $6,600HomeGuide retrofit band at $40–$65/ft; CostHelper: difficult layouts or a home that never had ducts runs $5,000–$15,000+

Where the money goes

Part of the jobShareNote
Duct materials — per linear foot$1 – $15Material-only, excl. labor and markup: flexible non-insulated $1–$3, flexible insulated $2–$4, fiberboard $4–$6, sheet metal $7–$13 (HomeGuide) — This Old House agrees within a dollar
Installed — per linear foot$25 – $55HomeGuide’s installed band; CostHelper agrees at $35–$55 — but This Old House (Homewyse data) prices it at $16–$19/ft, a genuine disagreement between sources
Per duct run$270 – $500HomeGuide only — no other source publishes a per-run figure
Insulation and sealing$400 – $2,700Duct-wrap insulation $800–$2,000 whole-home; manual mastic sealing $400–$1,900; aerosol (Aeroseal) sealing $1,300–$2,700 (HomeGuide)
Inspections, asbestos, mold$40 – $6,000Initial duct inspection $40–$100; asbestos inspection $250–$850 and removal $700–$2,200; mold inspection $200–$650 and remediation $450–$6,000 (HomeGuide)
Permits and patch-ups$50 – $1,500+Permits $50–$250 (HomeGuide) — under $100 to several hundred (This Old House), nominal $10–$100 (CostHelper); drywall repair after cutting $300–$1,500+; adding a vent $250–$500 (HomeGuide)
A supply duct up close: HomeGuide prices replacement at $270–$500 per duct run, and its initial duct-replacement inspection at $40–$100 before any quote
A supply duct up close: HomeGuide prices replacement at $270–$500 per duct run, and its initial duct-replacement inspection at $40–$100 before any quote

What moves the price most

Home size is the first driver — HomeGuide’s table runs $1,400–$3,400 at 1,000–1,500 sq ft up to $4,900–$9,000 at 3,500–4,000 sq ft. Duct location and accessibility is the second: basement runs ($1,800–$3,100) price well below crawl-space work ($3,000–$7,300) because crews can actually reach them. Duct material moves the materials half from $1/ft (flexible) to $15/ft (sheet metal). Insulation needs in unconditioned attics and crawl spaces add $800–$2,000. Rerouting, cutting into floors or ceilings and older-home complications (asbestos, mold) add lines to the invoice. Local labor rates run metro over rural (This Old House), and permits are nominal but real. On DIY: This Old House calls full duct replacement a pro job — airflow design, sizing, codes and permits — while minor sealing or insulation repairs are the DIY-friendly part.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A technician’s inspection is the repair-or-replace verdict: minor fixes run $200–$700 in HomeGuide, while extensive leaks or corrosion mean the full $1,400–$5,600 replacement
A technician’s inspection is the repair-or-replace verdict: minor fixes run $200–$700 in HomeGuide, while extensive leaks or corrosion mean the full $1,400–$5,600 replacement

Frequently asked questions

How much does ductwork replacement cost?

The typical range is $1,400–$5,600, with HomeGuide’s national average at $3,500 across 399 projects (updated December 2025). This Old House (2026) frames it as under $2,000 for a small, straightforward project to over $8,000 for a large or complex system; CostHelper (2026) puts a single-family home at $1,000–$5,000 or more.

How much does ductwork cost per linear foot?

HomeGuide: $25–$55 installed per linear foot. CostHelper agrees at $35–$55. This Old House (Homewyse data) disagrees at $16–$19 per foot — a genuine disagreement; ask a contractor which basis their quote uses.

Should I repair or replace my ductwork?

Repair if the system is under about 10 years old with minor issues — localized leaks, small insulation damage, loose connections — at $200–$700 (HomeGuide). Replace with extensive leaks, corrosion, poor airflow in multiple rooms, bad design, or a system needing frequent repairs (This Old House).

How long does ductwork last?

10–20 years on average (HomeGuide). This Old House’s rule of thumb: 10–15 years, with flexible ducts at the short end and sheet metal at 20+ years.

Does replacing ductwork save energy?

HomeGuide: replacing leaky ducts saves 10–40% on energy bills. An energy auditor cited by This Old House says duct leakage alone can account for 20% or more of a home’s heating and cooling energy loss.

How long does ductwork replacement take?

One to 2 days for a basic layout; 4 or more days for a large or complex system (HomeGuide and This Old House agree).

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Ductwork Replacement cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Hand adjusting a modern black smart thermostat with a Wi-Fi icon on the wall

Smart Thermostat Installation Cost

$200 – $500

A smart thermostat installed by a pro averages $300 — Fixr’s national figure (updated January 2025) for a C-wire install plus an auto-schedule smart thermostat with a two-year warranty. HomeGuide (August 2025) puts the average smart install at $225–$400; Angi (July 2026) gives the widest band, $175 to over $1,000, with the high end reserved for relocations, new wiring and multi-unit jobs. No source publishes a labor-vs-device percentage split; Fixr’s average is the only smart-only national figure.

Two workers inspecting a brick chimney with clay flue tiles and a rain cap on a rooftop

Chimney Liner Replacement Cost

$1,500 – $5,000

A standard chimney reline averages $2,500 — Angi’s national figure (updated September 2026), with typical pro jobs landing at $1,500–$5,000. HomeGuide (February 2026) averages relining at $1,200–$4,600; Flue-Pipes’ 2026 guide prices a professional stainless reline at $1,500–$3,800, with complex jobs — tall chimneys, difficult access, cast-in-place liners — reaching $7,000 or more. Angi is the only source publishing a national average; Flue-Pipes’ labor share (40–60% of the pro price) is the only published percentage.

Technician repairing electrical equipment on a workbench, motor and wiring in hand

Furnace Repair Cost

$350 – $505

A typical furnace repair lands at $350–$505 — the honest overlap of the three published typical ranges: HomeAdvisor (Angi) $133–$505, Fixr $150–$600 and Modernize $350–$900. Published averages disagree more than the ranges do: $318 (HomeAdvisor), $350–$400 (Fixr) and around $600 (Modernize, whose average pulls in major repairs). $350 is published here as the most-pay figure because it sits inside Fixr’s average band and just above HomeAdvisor’s; it is not a cross-source average. Major repairs run to $2,000+ and heat-exchanger replacement to $3,500.

HVAC technician kneeling beside a large outdoor unit with manifold gauges in hand

HVAC Maintenance Cost

$175 – $300

Annual HVAC maintenance typically costs $175 – $300 for a one-system plan with two seasonal tune-ups, with about $250 the figure most plans land near — Angi prices annual tune-ups at $175–$350 with a $250 average, and HomeGuide prices an annual service at $150–$300. This guide prices a maintenance plan for one system — inspection, cleaning and tune-ups for heating and cooling — not repairs, which are billed separately.

Close-up of a white finned radiator

Boiler Repair Cost

$200 – $660

A typical boiler repair lands at $200–$660 — the honest overlap of Angi’s most-pay range ($190–$660), Modernize’s typical range ($200–$1,000), Fixr’s oil-boiler repair range ($150–$750) and McQuillan Home Services’ standard repairs ($150–$750). The most-pay figure, $425, is Angi’s national average across 5,251 verified projects (updated September 2026) — the only whole-market single-point average among the independent sources. Fixr’s $450 is electric-boiler-only and is not used as a general average.

Outdoor heat pump unit standing beside a modern house

Heat Pump Repair Cost

$161 – $650

A typical air-source heat pump repair lands at $161–$650 — the honest overlap of Angi $161–$661, Fixr $150–$650 and Modernize $150–$650, a band all three sources support within $11 at each end. The most-pay figure, $400, is published as a national average by both Fixr and Modernize; Angi publishes around $410 from 4,007 verified projects (updated October 2026). Figures here are for residential air-source work only: geothermal and hybrid figures in Fixr and Modernize run higher and are not folded into the headline.