Home › Cost Guides › Vaulted Ceiling Installation
Cost Guide

How Much Does a Vaulted Ceiling Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$18,000 – $30,000
Most homeowners pay around $20,000 · Vaulting a ceiling in an existing home — typically a 20×20 ft living room opened to the roofline as a cathedral vault, with new rafters and a ridge beam, insulation and drywall — typically costs $18,000–$30,000, with most homeowners paying around $20,000, about $50–$70 per sq ft.
typical
$18,000$30,000
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Open-plan living room with a vaulted ceiling, exposed timber trusses, skylights and a stone fireplace

Vaulted Ceiling Installation cost at a glance

  • Typical range: $18,000 – $30,000
  • Most homeowners pay: around $20,000
  • Per square foot: $50–$70 per sq ft

Cross-checked against four published sources for this project. Sources used for this page: Angi, How Much Does It Cost to Vault a Ceiling? [2026 Data] (updated Oct 30, 2026 — national average $19,900, most $4,800-$38,000 across all vault types; new construction $16,000-$21,000, existing construction $18,000-$35,000; per sq ft $50-$75 (raise-a-ceiling average $19,200); by room bathroom/bedroom/kitchen $12,000-$18,000, living room $18,000-$25,000, garage $18,000-$35,000, basement $10,000-$90,000; by type groin/dome/rib $4,800-$10,000, barrel $5,000-$10,200, cathedral $16,000-$35,000; labor up to 75% of total, $13,500-$26,250; site prep $1,100-$6,200; permits $200-$2,000; electrical rerouting $200-$500, insulation $1,300-$3,300, duct replacement ~$1,180, skylight $1,100-$2,700, painting $1,600-$2,600; value add up to 25% in small-home markets, little in competitive markets); HomeGuide, How Much Does a Vaulted Ceiling Cost? (published Jul 20, 2023, updated Feb 11, 2026 — national average $20,600, average range $14,000-$27,000, min $10,000 / max $35,000; per sq ft $40-$70; new construction $10,000-$21,000, vaulting/raising an existing ceiling $16,000-$30,000; living room $16,000-$28,000, 20x20 ft room $16,000-$28,000; whole-ceiling-into-attic $64,000-$112,000, garage $23,000-$40,300; dome/barrel/groin/rib $5,000-$20,000; tray ceiling $3-$7 per sq ft; demolition $4-$10 per sq ft, insulation $1-$4 per sq ft, drywall $1.50-$3.50 per sq ft, painting $1-$2 per sq ft; architect $100-$250/hr, structural engineer $100-$220/hr, electrician $40-$100/hr, plumber $45-$150/hr; permits $500-$2,000; roof framing $5-$14 per sq ft (trusses) or $7-$30 per sq ft (rafters); steel beam $100-$400 per linear ft installed; skylight $1,600-$4,200); ThePricer, How Much Does It Cost to Raise a Ceiling Height? (updated Oct 2, 2026 — CORROBORATING SYNTHESIS, not fully independent: its headline figures explicitly cite HomeGuide and Angi — existing-ceiling vault $16,000-$30,000, 20x20 living room $16,000-$28,000, 15x15 bedroom $9,000-$15,800, garage $23,000-$40,300, large area $40,000-$100,000+, whole 40x40 ceiling into attic $64,000-$112,000, $40-$70 per sq ft; own synthesis: worked 20x20 example totalling $26,700 — engineering $2,500, demolition $2,000, structural framing $11,000, HVAC relocation $2,500, electrical $1,500, insulation + air sealing $2,500, drywall/finishing $2,500, painting $1,200, permits $1,000; structural engineer $2,000-$8,500 per project ($70-$250/hr); permits $600-$3,600+; plumbing-vent relocation $900-$3,000; duct relocation $25-$55 per linear ft; skylight $1,600-$4,200; warns there is no defensible rule that a vault adds 20-30% to home value). HomeAdvisor is the same company as Angi and repeats its figures; Bob Vila and EngineerFix repeat Angi's figures verbatim — none counted as independent. Disagreements flagged, not averaged away: per-sq-ft $40-$70 vs $50-$75 (overlap $50-$70); existing-home conversion $16,000-$30,000 vs $18,000-$35,000 (overlap $18,000-$30,000, full spread $16,000-$35,000); permits $200-$2,000 vs $500-$2,000 vs $600-$3,600+; skylight $1,100-$2,700 vs $1,600-$4,200. Breakdown rows are task costs with labor embedded, not a separate labor row. Worked example and shares are derived from the source ranges, not published percentages. Checked November 2026.. Sources last checked: October 2026 — HomeAdvisor, HomeGuide, Angi, ThePricer. How we calculate these costs

Cost by scope

Vaulted Ceiling Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Budget — Shallow decorative vault styles$4,800 – $10,200Dome, barrel, groin or rib vaults — shallow profiles that need little or no roof modification, but still need attic space above. Angi prices groin, dome and rib vaults at $4,800–$10,000 and barrel vaults at $5,000–$10,200.
Mid-range — Standard cathedral vault, one room$16,000 – $30,000A full cathedral vault in one existing room — rafters moved, ridge beam set, HVAC and wiring rerouted, insulation and drywall. HomeGuide prices an existing-home vault at $16,000–$30,000; Angi at $18,000–$35,000; a 20×20 ft living room runs $16,000–$28,000 (HomeGuide; ThePricer).
Premium — Complex conversion, truss roof or large area$30,000 – $100,000+A truss roof that has to be re-engineered, major HVAC and plumbing reroutes, or a large area — whole-ceiling-into-attic jobs run $64,000–$112,000 (HomeGuide) and large areas $40,000–$100,000+ (ThePricer).

Where the money goes

Part of the jobShareNote
Structural framing & ridge beam45% of total$9,000 — about $22.50 per sq ft, inside HomeGuide's $7–$30 per sq ft rafter-framing band. Share derived from the worked example below, not a published percentage.
Demolition & disposal of the old ceiling8% of total$1,600 — $4 per sq ft, at HomeGuide's $4–$10 per sq ft floor. Share derived from the worked example below, not a published percentage.
Structural engineering & permits10% of total$2,000 — at the low end: ThePricer prices engineering alone at $2,000–$8,500 per project and permits at $600–$3,600+, so a complex job pushes this line well above the example. Share derived from the worked example below, not a published percentage.
HVAC & electrical rerouting15% of total$3,000 — Angi prices electrical rerouting at $200–$500 and duct replacement at about $1,180; ThePricer prices HVAC relocation at $2,500. Share derived from the worked example below, not a published percentage.
Insulation, drywall & painting22% of total$4,400 — Angi prices vaulted-ceiling insulation at $1,300–$3,300; HomeGuide prices drywall at $1.50–$3.50 per sq ft and painting at $1–$2 per sq ft. Share derived from the worked example below, not a published percentage.
Structural framing & ridge beam · 45%Demolition & disposal of the old ceiling · 8%Structural engineering & permits · 10%HVAC & electrical rerouting · 15%Insulation, drywall & painting · 22%
Estimator’s note: on a vaulted ceiling installation, structural framing & ridge beam is usually where quotes swing most (45% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
A timber-frame vault with tall windows — the finished ceiling follows the roofline, so the room gains the whole attic volume
A timber-frame vault with tall windows — the finished ceiling follows the roofline, so the room gains the whole attic volume

What moves the price most

Roof framing type: rafter roofs are the straightforward case — HomeGuide prices rafter framing at $7–$30 per sq ft — while engineered truss roofs are far harder and costlier to rework, because the trusses carry the roof load and have to be re-engineered, not just removed (HomeGuide; Angi). Room size and location: Angi prices by room — bathroom, bedroom or kitchen $12,000–$18,000, living room $18,000–$25,000, garage $18,000–$35,000 — and a 20×20 ft living room runs $16,000–$28,000 (HomeGuide; ThePricer). Vault style: shallow dome, barrel, groin and rib vaults run $4,800–$10,200 (Angi) because they need little roof work; the cathedral vault most people picture runs $16,000–$35,000 (Angi) because the rafters have to move. Reroutes: electrical rerouting runs $200–$500 (Angi), duct replacement about $1,180 (Angi), HVAC relocation $2,500 (ThePricer), and plumbing-vent relocation $900–$3,000 (ThePricer) — the more services cross the ceiling, the higher the bill. Engineering and permits: a structural engineer runs $100–$220 an hour (HomeGuide) or $70–$250 an hour and $2,000–$8,500 per project (ThePricer); permits run $200–$2,000 (Angi) vs $500–$2,000 (HomeGuide) vs $600–$3,600+ (ThePricer) — publish the full $200–$3,600+ span, since the sources disagree on the typical band. Labor: Angi puts labor at up to 75% of the total, $13,500–$26,250 — the rows above are task costs with labor embedded in each task (like ThePricer's worked example), not a separate labor row. Insulation and energy: vaulted-ceiling insulation runs $1,300–$3,300 (Angi) or $1–$4 per sq ft (HomeGuide); the bigger volume costs more to heat and cool, and ventilation changes with the lost attic space (Angi). Skylights: a popular add-on once the roof is open — $1,100–$2,700 (Angi) vs $1,600–$4,200 (HomeGuide; ThePricer). Where the sources disagree: per-sq-ft spans are HomeGuide/ThePricer $40–$70 vs Angi $50–$75 — the honest overlap is $50–$70. Existing-home conversion is HomeGuide $16,000–$30,000 vs Angi $18,000–$35,000 — overlap $18,000–$30,000, full published spread $16,000–$35,000. National average is Angi $19,900 vs HomeGuide $20,600 — either rounds to about $20,000. Angi's $4,800–$38,000 typical range spans ALL vault types, including cheap dome and barrel vaults — it is not the range for a standard cathedral conversion. Source caveat: only Angi and HomeGuide are fully independent here. ThePricer's headline figures explicitly cite HomeGuide and Angi, so it is corroboration and synthesis — its value is the worked 20×20 example ($26,700) and the wider permit and engineering bands — not a third independent measurement. Cheaper alternatives: a tray ceiling ($3–$7 per sq ft, HomeGuide) or a coffered ceiling ($10–$40 per sq ft) gives a vaulted look without structurally raising the ceiling. Value: there is no fixed return — Angi says a vault can add up to 25% to home value in small-home markets and little in competitive markets; ThePricer warns there is no defensible rule that a vault adds 20–30%. Worked example at the most-pay figure: a 20×20 ft (400 sq ft) living room vaulted as a cathedral ceiling — structural framing and ridge beam $9,000 + demolition and disposal of the old ceiling $1,600 + structural engineering and permits $2,000 + HVAC and electrical rerouting $3,000 + insulation, drywall and painting $4,400 = $20,000. The shares are whole-percent roundings of this worked example. For the skylight that often goes with it see our skylight installation guide, for the beam version see our ceiling beam installation guide, for the fan that often goes with it see our ceiling fan installation guide, for the insulation see our attic insulation guide, for the wall work see our drywall installation guide, for the recessed version see our tray ceiling installation guide, and for the grid version see our coffered ceiling installation guide.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
Skylights set into a vaulted wood ceiling — a common add-on once the roof is opened up, at $1,100–$2,700 (Angi) to $1,600–$4,200 (HomeGuide). Portrait source — 1200x800 centre crop keeps the skylights and chandelier, re-verified after processing
Skylights set into a vaulted wood ceiling — a common add-on once the roof is opened up, at $1,100–$2,700 (Angi) to $1,600–$4,200 (HomeGuide). Portrait source — 1200x800 centre crop keeps the skylights and chandelier, re-verified after processing

Frequently asked questions

Can you vault any ceiling?

No. You need unused attic space above the room, no second story sitting on that ceiling, and a roof structure that can be re-engineered — engineered truss roofs complicate the job far more than rafter roofs (Angi; HomeGuide). A structural engineer has to confirm the roof can carry the change.

Do you need a permit to vault a ceiling?

Yes, in nearly all cases (Angi) — it is a structural change to the roof. Permits run $200–$2,000 (Angi), $500–$2,000 (HomeGuide) or $600–$3,600+ (ThePricer), depending on jurisdiction and whether the exterior roof changes too.

How long does vaulting a ceiling take?

None of the sources publishes a standard timeline. It is a multi-trade structural job — engineer, framing, HVAC, electrical, insulation, drywall and paint — so plan in weeks rather than days, and longer for truss roofs or major reroutes.

Does a vaulted ceiling add home value?

Maybe — it is market-dependent, with no fixed percentage. Angi says a vault can add up to 25% to home value in small-home markets and little in competitive markets where vaults are expected. ThePricer warns there is no defensible rule that a vault adds 20–30%.

What is the difference between a tray ceiling and a vaulted ceiling?

A tray ceiling is decorative — a recessed flat panel at $3–$7 per sq ft (HomeGuide) — while a vaulted ceiling structurally opens the room to the roofline. A tray gives some of the look for a fraction of the cost and no structural work.

What does the $50–$70 per sq ft cover?

The structural work, not just the finish: framing and ridge beam, demolition, engineering and permits, HVAC and electrical reroutes, insulation, drywall and painting. The published per-sq-ft range is $40–$75 depending on source — HomeGuide and ThePricer give $40–$70, Angi $50–$75 — so $50–$70 is the overlap.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Vaulted Ceiling Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Wood-panelled walk-in closet fitted with an open organizer system of shelves and hanging rods

Closet Organizer Installation Cost

$600 – $2,500

Installing a closet organizer system — laminate or MDF shelving, hanging sections and a drawer bank fitted into a standard reach-in closet that already exists, professionally installed — typically costs $600–$2,500, with most homeowners paying around $1,550, about $50–$150 per linear foot.

Modern living room with a black 3D-panel accent wall behind a low console, grey sofa in the foreground

Accent Wall Installation Cost

$400 – $2,000

Installing an accent wall — typically one wall of about 120 sq ft in painted shiplap or board and batten, professionally installed — typically costs $400–$2,000, with most homeowners paying around $900, about $2–$25 per sq ft depending on the finish.

Modern hallway with wooden doors and a sliding closet beside abstract wall art

Closet Door Installation Cost

$250 – $800

Installing new closet doors on one standard opening — a pair of bifold doors or a bypass set, professionally installed — typically costs $250–$800, with most standard jobs landing around $550.

A drywall finisher in a hard hat and respirator smoothing joint compound on a wall with a taping knife

Drywall Texture Installation Cost

$575 – $675

Texturing drywall in one room — a sprayed or hand-applied finish over new drywall, with masking and prep included — typically costs $575–$675, with most homeowners paying around $625, about $0.80–$2.00 per square foot of wall and ceiling surface.

A sunlit elevator lobby with closed ribbed elevator doors, a floor sign and an accessibility call panel

Dumbwaiter Installation Cost

$8,000 – $12,000

Installing a residential dumbwaiter — a small electric freight lift with a new shaft, landing doors and finish work — typically costs $8,000–$12,000, with most homeowners paying around $10,000.

Hands filling a bottle from a wall-mounted water-filter unit at a kitchen sink

Under-Sink Reverse Osmosis Installation Cost

$300 – $950

Installing an under-sink reverse osmosis system — a tank or tankless unit fitted below the kitchen sink, treating drinking and cooking water at one tap through its own dedicated faucet — typically costs $300–$950 installed, with most standard tank jobs landing around $625, the midpoint of the $300–$950 band (no surveyed under-sink average exists). This page covers under-sink systems only — whole-house reverse osmosis is a different job ($4,800–$8,000 installed) covered on our whole-house water filtration page.