Home › Cost Guides › Basement Insulation Installation
Cost Guide

How Much Does a Basement Insulation Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$1,000 – $5,000
Most homeowners pay around $2,600 · Insulating a standard 1,000-square-foot basement — fiberglass batts, rigid foam or spray foam fitted to the walls and rim joist, at $1–$5 per sq ft installed
typical
$1,000$5,000
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Construction worker in a yellow hard hat and orange reflective vest holding a hammer in front of an exposed wooden stud wall with white fiberglass insulation between the studs

Basement Insulation Installation cost at a glance

  • Typical range: $1,000 – $5,000
  • Most homeowners pay: around $2,600
  • Per square foot: $1–$5 per sq ft
  • Prices vary most by: Insulation materials (40–60% of the budget)

Cross-checked against three published sources for this project. Sources used for this page: Angi's basement insulation cost guide, updated October 12, 2026 (national average $2,600, most $1,000–$5,000; fiberglass batting $0.60–$2.30, wool $1.10–$3.10, blown-in $1–$2, rigid foam $0.25–$3, spray foam $0.50–$4 per sq ft; size table: 500 sq ft $700–$1,500, 750 $750–$2,100, 1,000 $1,000–$3,000, 1,200 $1,200–$3,600, 1,500 $1,500–$5,000; general contractors 10–50% of project cost; insulation permit $140–$500, basement remodel permit $150–$2,000; mold remediation $1,225–$3,750; R-value per inch: fiberglass 3.5–3.7, wool 3.5–3.8, rigid foam 3.6–8.0, spray foam 3.5–7.0), HomeGuide's basement insulation cost guide (2026) ($1–$5 per sq ft of wall or ceiling area, about $1,300–$5,000 total for a 1,000 sq ft basement; fiberglass batts $1.00–$2.60, wool $1.50–$3.80, spray foam $1.50–$5.00, rigid foam board $1.20–$3.70 per sq ft installed; labor $40–$80+ per hour; building codes typically require R-10 to R-15 for basement walls) and HomeAdvisor's 2026 insulation cost data (basement $1.50–$2.50 per sq ft, $1,400–$6,300 on average; material $0.25–$6.75 per sq ft by type). Synthesized typical = Angi's most-pay band at $1,000–$5,000, with $2,600 most-pay at Angi's published national average. Checked November 2026.. Sources last checked: October 2026 — HomeAdvisor, HomeGuide, Angi. How we calculate these costs

Cost by scope

Basement Insulation Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Budget — fiberglass batts, walls only$1,000 – $2,000Angi prices fiberglass batting at $0.60–$2.30 per square foot and its 1,000 sq ft table at $1,000–$3,000; HomeGuide prices fiberglass batts installed at $1.00–$2.60 per square foot.
Standard — rigid foam board or fiberglass, walls + rim joist$1,500 – $3,000The typical project on this page: Angi's 1,000 sq ft table is $1,000–$3,000 and HomeGuide prices a 1,000 sq ft basement at $1,300–$5,000.
Premium — closed-cell spray foam, walls + rim joist sealed$3,000 – $5,000Angi prices spray foam at up to $4 per square foot installed and HomeGuide at $1.50–$5.00 per square foot — a 1,000 sq ft basement at the top of the most-pay band.

Where the money goes

Part of the jobShareNote
Insulation materials40–60% of totalAngi prices materials at $0.60–$4 per square foot by type, and HomeGuide prices materials at $0.50–$2.80 per square foot plus labor at $0.50–$1.70
Installation labor30–50% of totalHomeGuide prices basement insulation labor at $40–$80+ per hour, and Angi prices general contractors at 10–50% of the project cost
Air sealing & vapor barrier5–15% of totalSealing the rim joist and wall gaps is the small line that makes the insulation work; closed-cell spray foam bundles air sealing into its own price
Permits & prep5–10% of totalAngi prices an insulation permit at $140–$500; mold remediation before insulating runs $1,225–$3,750 if the basement has moisture problems
Insulation materials · 40–60%Installation labor · 30–50%Air sealing & vapor barrier · 5–15%Permits & prep · 5–10%
Estimator’s note: on a basement insulation installation, insulation materials is usually where quotes swing most (40–60% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
Exposed stud walls with white fiberglass batts fitted between them — the batts are the budget material on this page, at $0.60–$2.30 per square foot in Angi's data
Exposed stud walls with white fiberglass batts fitted between them — the batts are the budget material on this page, at $0.60–$2.30 per square foot in Angi's data

What moves the price most

Material is the first lever: Angi prices fiberglass batting at $0.60–$2.30 per square foot against spray foam at up to $4, and HomeGuide prices the same spread at $1.00–$2.60 for batts against $1.50–$5.00 for spray foam — foam costs roughly twice the batt price per square foot. Size is second: Angi's size table runs $700–$1,500 for 500 square feet, $1,000–$3,000 for 1,000 and $1,500–$5,000 for 1,500, so a standard 1,000-square-foot basement is the average this page is priced on. R-value is third: HomeGuide says building codes typically require R-10 to R-15 for basement walls, and Angi prices R-value per inch at 3.5–3.7 for fiberglass, 3.6–8.0 for rigid foam and 3.5–7.0 for spray foam — colder climates need more inches. Moisture and prep are fourth: Angi prices mold remediation at $1,225–$3,750 before insulating, and HomeGuide says spray foam and rigid foam double as vapor barriers where batts do not. Worked example at the most-pay figure: insulation materials $1,300 + labor $800 + air sealing & vapor barrier $300 + permit $200 = $2,600. For the insulation above the basement, see our attic insulation guide and our crawl space insulation guide, and for the walls themselves see our wall insulation guide.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
Sealing a window frame with acoustical sealant over pink fiberglass batts: air sealing is 5–15% of an insulation bill on this page — Angi prices an insulation permit at $140–$500
Sealing a window frame with acoustical sealant over pink fiberglass batts: air sealing is 5–15% of an insulation bill on this page — Angi prices an insulation permit at $140–$500

Frequently asked questions

How much does it cost to insulate a basement?

Typically $1,000–$5,000, averaging $2,600 in Angi's 2026 data — and HomeGuide prices a 1,000 sq ft basement at $1,300–$5,000.

How much does basement insulation cost per square foot?

$1–$5 per square foot installed in HomeGuide's data; HomeAdvisor prices $1.50–$2.50 per square foot, or $1,400–$6,300 on average.

What is the cheapest insulation for a basement?

Fiberglass batts: $0.60–$2.30 per square foot in Angi's data and $1.00–$2.60 installed in HomeGuide's — the budget material on this page.

Do I need a permit to insulate a basement?

Often yes — Angi prices an insulation permit at $140–$500, and a basement remodeling permit at $150–$2,000 where the job is part of a remodel.

What R-value does a basement need?

Building codes typically require R-10 to R-15 for basement walls in HomeGuide's data, and colder climates need more. See our wall insulation guide for the same materials in above-grade walls.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Basement Insulation Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides