Soffit and Fascia Installation cost at a glance
- Typical range: $1,500 – $5,000
- Most homeowners pay: around $3,200
- Prices vary most by: Panels and boards (35–45% of the budget)
Cross-checked against three published sources for this project. Sources used for this page: HomeGuide's soffit and fascia replacement cost guide (whole eave $9–$34 per linear foot, $900–$6,800 for 100–200 linear feet; fascia $5–$12 per linear foot, soffit $4–$22 per linear foot for 1–2 foot widths; labor $2–$7 per linear foot for each board; 150 linear feet combined $1,350–$5,100; rotted-eave repair around $650–$4,000; painting both $400–$2,800), Angi's vinyl soffit guide, updated October 14, 2026 (vinyl soffit $1,625–$3,500, average $2,550, $6.50–$14 per linear foot installed; fascia add-on $5–$8 per linear foot; removal $1–$4 per linear foot), Angi's aluminum soffit guide, updated October 7, 2026 (aluminum soffit $2,100–$4,500, $8–$20 per linear foot; fascia $7–$22 per linear foot), Angi's fascia board guide, updated October 8, 2026 (fascia $1,050–$3,300, average $2,500, $7–$22 per linear foot; complex rooflines to $40 per linear foot; typical job 1–2 days) and ThePricer's soffit and fascia guide, updated August 9, 2026 (combined $900–$6,800 for 100–200 linear feet, $9–$34 per linear foot; fascia $1,050–$3,300 averaging $2,500; soffit alone $1,000–$4,000 averaging $2,200). The page's typical band is the HomeGuide 150-foot combined table, and its $3,200 most-pay figure sits near that table's midpoint. Sources last checked: October 2026 — HomeGuide, Angi, ThePricer. How we calculate these costs
Cost by scope

| Scope | Typical cost | What it includes |
|---|---|---|
| Fascia only, one side or a short run | $600 – $1,800 | A single elevation or a short run: HomeGuide's one-side band against Angi's fascia-only $1,050–$3,300 — gutters removed and refitted, boards replaced, no soffit work |
| Soffit and fascia together, full one-story perimeter — the typical job | $1,500 – $5,000 | The shared band: HomeGuide's 150-foot combined table at $1,350–$5,100 against ThePricer's $900–$6,800 for 100–200 feet — vinyl or aluminum, both boards, removal and venting included |
| Two-story home, or rot and rafter-tail repair found at removal | $3,500 – $8,500 | The expensive end: two-story access and scaffolding plus rotted-eave repair, which HomeGuide prices around $650–$4,000 on its own — the contingency tier, not the standard job |
Where the money goes
| Part of the job | Share | Note |
|---|---|---|
| Panels and boards | 35–45% of total | Vinyl soffit installs at $6.50–$14 per linear foot and aluminum at $8–$20 in Angi's guides, with fascia boards on top — material choice is the second-biggest lever after footage |
| Labor, removal and installation | 35–45% of total | HomeGuide prices labor at $2–$7 per linear foot for each board, and Angi's fascia labor at $6–$20 per foot on top of materials — two boards, two passes along the same edge |
| Removal and disposal | 5–15% of total | Angi's vinyl soffit guide prices removal at $1–$4 per linear foot for soffit and the same for fascia — old boards come off before new ones go on |
| Vents, fasteners and trim | 5–10% of total | Continuous venting, J-channel, fasteners and caulk — small lines that decide whether the new eave actually ventilates the roof |

What moves the price most
Linear feet are first: HomeGuide's whole-eave table runs $9–$34 per linear foot, so a 100-foot home and a 200-foot home are different jobs at the same rate — measure the roof edge, not the floor plan. Material is second: vinyl is the lowest installed cost, aluminum sits above it, and wood needs painting every few years, which is a running cost the guides price separately. Height and access are third: one-story work runs off ladders, two-story work needs scaffolding, and complex rooflines push Angi's fascia rate toward $40 per linear foot in extreme cases. Hidden rot is fourth: fascia and soffit hide rafter tails, and HomeGuide prices rotted-eave repair around $650–$4,000 — a quote that skips the rot check is not comparable with one that includes it. For the gutters that hang from the new fascia, see our gutter installation guide and gutter guard guide, and for the roof above the edge, see our roof replacement guide.
Worked example: how a typical soffit and fascia installation budget breaks down
Take the typical job — a one-story home, about 150 linear feet of roof edge, vinyl soffit and fascia together: old boards off, new boards on, vents fitted, gutters refitted. Here is a realistic $3,200 version of that invoice: The budget below totals $3,200 — the "most homeowners pay around" figure from the top of this page — split using this page's own cost breakdown. It shows how a real quote at that level is usually composed; every line is built from the ranges on this page, and it is an illustration, not a quote for your project.
| Line item | Example budget |
|---|---|
| Vinyl panels and fascia boards | $1,400 |
| Labor, removal and installation | $1,300 |
| Removal and disposal | $300 |
| Vents, fasteners and trim | $200 |
| Total | $3,200 |
What most people get wrong
- Replacing one board and leaving the rot — fascia hides rafter tails, and new boards over rotted framing fail with the framing, not the boards.
- Painting over rotted fascia instead of replacing it — paint seals the damage in and the rot keeps spreading behind it.
- Skipping venting when the soffit is replaced — solid panels where vents belonged starve the roof of airflow, and the next problem is condensation, not cosmetics.
- Comparing a per-foot quote that excludes removal with one that includes it — removal runs $1–$4 per foot per board, and only the scope list makes two per-foot prices comparable.
Costs in your city
Soffit and fascia work is crew-labor pricing around panels and boards: the same 150-foot perimeter quotes near the bottom of the band where crew rates are low and toward the top in a high-cost metro, while vinyl and aluminum ship nationally. Climate travels with the city — humid and coastal markets find more rot at removal, and two-story suburbs carry more scaffolding than one-story tracts. Ask each bidder for the linear footage measured, the material, and whether removal, vents and gutter refitting are included.

Frequently asked questions
What is the difference between soffit and fascia?
The fascia is the vertical board along the roof's edge that the gutters hang from; the soffit is the horizontal panel underneath the overhang, back to the house wall. They are priced per linear foot as a pair because they share the same edge.
How much does soffit and fascia replacement cost per linear foot?
HomeGuide prices the whole eave at $9–$34 per linear foot installed — fascia $5–$12 and soffit $4–$22 separately. Angi's installed bands run higher for aluminum ($8–$20 for soffit, $7–$22 for fascia).
Should soffit and fascia be replaced together?
Usually yes: the fascia must come off to properly access and install the soffit, so doing one without the other means paying the access labor twice. Angi's guides recommend replacing both when either fails.
How long does soffit and fascia replacement take?
Angi's fascia guide puts a typical replacement at 1 to 2 days for a standard home. Two-story work, long perimeters and rot repair extend it.
Do I need new gutters too?
Not necessarily: gutters are removed and refitted as part of a fascia job in HomeGuide's pricing, but gutter replacement itself is a separate charge, priced on its own page.






