Home › Cost Guides › Radiant Floor Heating Installation
Cost Guide

How Much Does a Radiant Floor Heating Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$1,653 – $6,656
Most homeowners pay around $4,128 · A typical radiant floor heating project — Angi’s 2026 national range is $1,653–$6,656 averaging $4,128, and BlockRenovation’s average project lands at ~$4,000, agreeing within $128
typical
$1,653$6,656
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Bare feet on a sunlit tiled bathroom floor beside a bathtub

Radiant Floor Heating Installation cost at a glance

  • Typical range: $1,653 – $6,656
  • Most homeowners pay: around $4,128

Cross-checked against two published sources for this project. Sources used for this page: the Angi radiant floor heating cost guide (October 2026), BlockRenovation's 2026 heated-floor cost guide and Modernize's underfloor heating cost guide (updated August 2026). Sources last checked: October 2026 — Modernize, Angi. How we calculate these costs

Cost by scope

Radiant Floor Heating Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Single bathroom, electric (~40 sq ft)$300 – $1,200The classic single-room job — Block: $300–$700 heating only; Modernize: $500–$1,200 installed. Electric is the favorite for bathrooms and kitchens
Kitchen or primary bath (120–160 sq ft)$1,100 – $3,000Block: $1,100–$2,700 heating only; Modernize’s kitchen band runs $1,200–$3,000 installed
Larger room — living room or basement (320–1,000 sq ft)$2,200 – $17,000Block’s heating-only room figures — living room (320 sq ft) $2,200–$5,400, basement (1,000 sq ft) $7,000–$17,000
Whole-home hydronic (1,500–2,000 sq ft)$12,000 – $48,000The sources genuinely disagree at this scale — Modernize $12,000–$35,000+, Block $13,700–$43,000 (plus $3,200–$9,000 for a boiler), Angi $19,000–$48,000; presented per source, never merged
Heating plus new flooring$10 – $40 per sq ftBlock’s combined band once the floor itself is replaced — tile or stone $15–$40, concrete $11–$25, laminate $10–$25

Where the money goes

Part of the jobShareNote
Electric system, installed$8 – $15 per sq ftThe corroborated anchor — all three sources publish this exact band; cheapest to install, costliest to run
Hydronic system, installed$6 – $20 per sq ftAngi and Modernize publish $6–$20; Block publishes $7–$17 — genuine partial disagreement on the floor and ceiling, recorded as published
Boiler, if your home doesn’t have one$3,200 – $9,000Block’s figure — the line that turns hydronic whole-home totals into five-figure territory; a dedicated water heater ($600–$3,100) can serve small 1–2 room systems
Thermostat, per zone$140 – $350 installedBlock’s add-on figure — each zone needs its own control
Labor$550 – $2,500 per projectAngi’s total labor band — plumbers $45–$200/hr, electricians $50–$100/hr, roughly 12 hours of labor per 1,000 sq ft heated; no source publishes a labor-vs-materials percentage split
The install itself — electric systems run $8–$15 a square foot installed (all three sources), hydronic $6–$20; tile and stone conduct the heat best.
The install itself — electric systems run $8–$15 a square foot installed (all three sources), hydronic $6–$20; tile and stone conduct the heat best.

What moves the price most

System type decides the shape of the bill. Electric ($8–$15/sq ft, all three sources) is cheapest to install and the favorite for single rooms; hydronic ($6–$20) costs more upfront but much less to run — Block puts a 1,500 sq ft home at $65–$165 a month hydronic versus $90–$250 electric. Project size scales it: a 40 sq ft bathroom starts at $300–$1,200 while whole-home hydronic runs into the tens of thousands, with the three sources publishing genuinely different whole-home bands. Flooring choice matters — tile and stone conduct heat best and run $15–$40/sq ft combined with the heating; carpet needs thin, low-tog types. Retrofit versus new construction is the biggest multiplier: retrofits typically cost 50–80% more than the same system in new construction (Block) — floor removal alone runs $1.50–$10/sq ft. Labor rates vary hard by market (plumbers $45–$200/hr per Angi), and large electric systems may need electrical panel upgrades. Subfloor insulation ($1–$5/sq ft) and permits ($75–$180) round out the invoice (Block). Lifespan: 30–50 years for the tubing itself (Block), though boilers get replaced every 15–20 years (Angi).

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
Each zone gets its own thermostat — $140–$350 installed per zone (BlockRenovation), the small line that keeps multi-room bills sane.
Each zone gets its own thermostat — $140–$350 installed per zone (BlockRenovation), the small line that keeps multi-room bills sane.

Frequently asked questions

How much does radiant floor heating cost?

Typically $1,653–$6,656 — Angi’s 2026 national range, averaging $4,128; BlockRenovation’s average project is ~$4,000, agreeing within $128.

Is electric or hydronic radiant heating cheaper?

Electric costs less to install ($8–$15/sq ft, all three sources) but more to run; hydronic runs $6–$20/sq ft (Angi, Modernize) or $7–$17 (Block) and costs much less to operate — $65–$165 a month versus $90–$250 for electric on a 1,500 sq ft home (Block).

Can radiant heating go under an existing floor?

Yes, but retrofits typically cost 50–80% more than the same system in new construction (Block) — the old floor has to come up ($1.50–$10/sq ft) and heights may need adjusting. Angi calls some under-floor retrofits ‘almost impossible’ without opening the floor.

How much does a heated bathroom floor cost?

$300–$1,200 for the heating in a ~40 sq ft bath (Block, Modernize); $600–$1,600 with new flooring included (Block).

Do I need a boiler for radiant floor heating?

Only for hydronic systems without one — $3,200–$9,000 installed (Block). Small 1–2 room hydronic systems can use a dedicated water heater ($600–$3,100) instead.

How long does radiant floor heating last?

30–50 years for the coils or tubing (Block); 15–50 years overall depending on system (Angi), with hydronic boilers or heat pumps replaced every 15–20 years.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Radiant Floor Heating Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Wall-mounted panel radiator in warm sunlight beside a carpeted floor

Baseboard Heater Installation Cost

$420 – $1,526

Baseboard heater installation typically costs $420 – $1,526 for a standard project, with about $973 the figure most jobs land near — Angi's national average is $973 inside its $420–$1,526 most-pay band. This guide prices electric and hydronic baseboard units installed by a pro, per unit and per project.

Clean wall-mounted indoor mini-split air conditioning unit

Mini-Split Installation Cost

$2,000 – $8,000

A professionally installed single-zone system — Angi ($2,000–$5,000 typical, ~$3,000 average), Modernize ($3,000–$8,000 installed) and USA Today ($2,000–$7,000 per zone) overlap at $2,000–$8,000; no single national average exists — the sources genuinely disagree ($3,000 vs $6,357 vs $8,500)

Technician adjusting a water pump indoors

Well Pump Replacement Cost

$900 – $2,500

A residential well pump replacement (pump + pull labor + pipework) runs $900–$2,500 installed for most homes — Angi’s 2026 national average is $1,897 across 1,339 verified projects (most paying $973–$2,822), This Old House puts the typical job at $900–$2,500 and LandClearingAndExcavation averages ~$1,900 across depths and pump types. Deep wells (300–400 ft) routinely run $2,800–$5,500+. Figures no source publishes: per-horsepower cost tables and a parts-vs-labor percentage split — omit those, never invent them.

White panel radiator on a brick wall

Boiler Replacement Cost

$3,200 – $9,000

A residential boiler replacement (equipment + labor) averages $6,100 — HomeGuide’s national figure (updated December 2025), with typical full swaps landing at $3,200–$9,000. This Old House puts equipment + labor at $4,500–$10,000; Modernize (August 2026) averages $6,500–$11,500 — its bands skew toward full installs rather than simple swaps. Gas is the most common fuel; high-efficiency/condensing models cost a clear premium. Figures no source publishes: a distinct national ‘most-pay’ figure, per-sq-ft installed pricing, and a 50% repair-vs-replace rule.

Home inspector examining a crawl space entrance

Crawl Space Encapsulation Cost

$5,000 – $15,000

Professional crawl space encapsulation averages $5,500 — Angi and This Old House (both 2026) publish the same average, with typical totals of $5,000–$15,000 (Modernize agrees, September 2026). Basic work runs $2–$4/sq ft (Angi) to $3–$7/sq ft (This Old House); extensive moisture-problem jobs reach $10/sq ft. Labor is 50–70% of the total; materials are 30–50% (Angi, This Old House).

Exposed sheet-metal air ducts and a supply register on a dark ceiling

Ductwork Replacement Cost

$1,400 – $5,600

Replacing a home’s air ducts averages $3,500 — HomeGuide’s national figure across 399 member projects (updated December 2025), with the typical range at $1,400–$5,600 by home size. This Old House (2026, Homewyse data) prices it at $16–$19 per linear foot — about $3,100–$3,700 for an average 200-foot system — and CostHelper (2026) agrees with HomeGuide’s installed band at $35–$55 per foot. No source publishes a labor-vs-materials percentage split; HomeGuide’s average is the only published national figure.