Home › Cost Guides › Baseboard Heater Installation
Cost Guide

How Much Does a Baseboard Heater Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$420 – $1,526
Most homeowners pay around $973 · Baseboard heater installation typically costs $420 – $1,526 for a standard project, with about $973 the figure most jobs land near — Angi's national average is $973 inside its $420–$1,526 most-pay band. This guide prices electric and hydronic baseboard units installed by a pro, per unit and per project.
typical
$420$1,526
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Wall-mounted panel radiator in warm sunlight beside a carpeted floor

Baseboard Heater Installation cost at a glance

  • Typical range: $420 – $1,526
  • Most homeowners pay: around $973
  • Prices vary most by: Electrical labor and wiring (35–50% of the budget)

Cross-checked against three published sources for this project. Sources used for this page: Angi's baseboard heater cost guide, updated September 29, 2026 (national average $973, most $420–$1,526; electric $40–$60 per linear foot; 3 ft/500 W $100–$250, 6 ft/1,000 W $200–$400, 8 ft/2,000 W $300–$600 per unit; electric units $150–$400, hydronic $400–$1,100, smart-enabled $600–$1,500 per unit; electrician labor $50–$120 per hour; removal $50–$200 per unit), HomeGuide's baseboard heater cost guide ($300–$1,100 per unit installed, national average $800; electric $200–$1,100, hydronic $430–$1,200 per unit installed; whole-home 18–26 units $5,400–$7,800; electric running costs $480–$900 per month) and Modernize's baseboard radiator guide, updated August 12, 2026 (typical $400–$1,070 per unit installed, national average about $750; heater unit $65–$200). The page's typical band is Angi's most-pay band and its $973 most-pay figure is Angi's published average. Sources last checked: October 2026 — HomeGuide, Modernize, Angi. How we calculate these costs

Cost by scope

Baseboard Heater Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Single electric unit, replacement on an existing circuit$200 – $1,100The cheap end: HomeGuide prices an electric unit at $200–$1,100 installed, and Angi prices electric units at $150–$400 per unit before labor — a like-for-like swap on an existing circuit
Standard room or two, several new units — the typical job$420 – $1,526The shared band: Angi's most-pay band with its $973 average, against HomeGuide's $300–$1,100 per unit and Modernize's $400–$1,070 per unit — new wiring and a thermostat included
Hydronic system or whole-home baseboard$5,400 – $7,800The expensive end: HomeGuide prices 18–26 units for a whole home at $5,400–$7,800, and hydronic units at $430–$1,200 each — a boiler or water-heater tie-in is a separate system, not a room heater

Where the money goes

Part of the jobShareNote
Heater units30–45% of totalElectric $200–$1,100 and hydronic $430–$1,200 per unit installed in HomeGuide's guide; Angi unit-only prices run $150–$400 electric and $400–$1,100 hydronic
Electrical labor and wiring35–50% of totalAngi prices electrician labor at $50–$120 per hour, and a new unit usually needs its own dedicated circuit — the labor line, not the heater, is what varies most
Thermostat and controls5–15% of totalLine-voltage or smart thermostats per room or zone; Angi prices smart-enabled units at $600–$1,500 installed, against $150–$400 for a standard electric unit
Panel capacity and removal5–15% of totalA panel upgrade if the service cannot take the new load, plus $50–$200 per unit to remove and dispose of old heaters in Angi's guide
Heater units · 30–45%Electrical labor and wiring · 35–50%Thermostat and controls · 5–15%Panel capacity and removal · 5–15%
Estimator’s note: on a baseboard heater installation, electrical labor and wiring is usually where quotes swing most (35–50% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
A fitter working above a wall radiator: installation labor is the line that varies most, at $50–$120 per hour in Angi's guide, because wiring, circuit work and wall access differ room by room
A fitter working above a wall radiator: installation labor is the line that varies most, at $50–$120 per hour in Angi's guide, because wiring, circuit work and wall access differ room by room

What moves the price most

Type is first: Angi unit prices run electric $150–$400, hydronic $400–$1,100 and smart-enabled $600–$1,500; HomeGuide installed prices run electric $200–$1,100 and hydronic $430–$1,200. Count is second: baseboard is priced per unit, so the total scales with rooms — HomeGuide's whole-home figure of 18–26 units at $5,400–$7,800 is simply the per-unit math at house scale. Electrical capacity is third: new units usually need dedicated circuits, and a panel that cannot take the load turns a heater job into an electrical job. Running cost is fourth, and it reverses the install logic: HomeGuide puts electric baseboard running costs at $480–$900 a month for a home, which is why electric is the cheapest to install and the most expensive to run — hydronic costs more up front and less per month. For the thermostat that controls the system, see our smart thermostat guide.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A classic column radiator with its control valve: thermostats and controls run 5–15% of a baseboard job, and smart-enabled units reach $600–$1,500 installed in Angi's guide against $150–$400 for a standard electric unit
A classic column radiator with its control valve: thermostats and controls run 5–15% of a baseboard job, and smart-enabled units reach $600–$1,500 installed in Angi's guide against $150–$400 for a standard electric unit

Frequently asked questions

How much does baseboard heater installation cost per unit?

HomeGuide prices $300–$1,100 per unit installed, Modernize $400–$1,070 with a national average around $750, and Angi prices a standard project at $420–$1,526 with a $973 average. Electric units sit at the low end, hydronic at the high end.

Electric or hydronic baseboard heat — which should I choose?

Electric is cheapest to install (HomeGuide $200–$1,100 per unit) and needs only wiring, but costs most to run. Hydronic ($430–$1,200 per unit) needs a boiler or water heater and plumbing, retains heat longer, and costs less per month — it wins where a boiler already exists.

Do I need a new circuit or a panel upgrade?

Usually a dedicated circuit per heater or zone — that is the standard electrical requirement in the guides. A panel upgrade is only needed if the service cannot take the added load, and it should be priced as its own line, not buried in the heater quote.

How much does electric baseboard heat cost to run?

HomeGuide puts electric baseboard running costs at $480–$900 a month for a home. That is the real long-term cost of the cheap install, and the reason many owners pair baseboard heat with a heat pump for the main living areas.

Can I install a baseboard heater myself?

A like-for-like electric swap on an existing circuit is the DIY case in Angi's guide ($200–$400 per unit for materials). New circuits, wiring and anything hydronic belong to a licensed electrician or plumber — and a hydronic tie-in is not a DIY job at all.

How many heaters does a room need?

Sizing runs by length and wattage: Angi prices 3 ft/500 W units at $100–$250, 6 ft/1,000 W at $200–$400 and 8 ft/2,000 W at $300–$600 per unit. Room size, insulation and window area decide the total watts — undersized heaters run constantly and still feel cold.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Baseboard Heater Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Clean wall-mounted indoor mini-split air conditioning unit

Mini-Split Installation Cost

$2,000 – $8,000

A professionally installed single-zone system — Angi ($2,000–$5,000 typical, ~$3,000 average), Modernize ($3,000–$8,000 installed) and USA Today ($2,000–$7,000 per zone) overlap at $2,000–$8,000; no single national average exists — the sources genuinely disagree ($3,000 vs $6,357 vs $8,500)

Technician adjusting a water pump indoors

Well Pump Replacement Cost

$900 – $2,500

A residential well pump replacement (pump + pull labor + pipework) runs $900–$2,500 installed for most homes — Angi’s 2026 national average is $1,897 across 1,339 verified projects (most paying $973–$2,822), This Old House puts the typical job at $900–$2,500 and LandClearingAndExcavation averages ~$1,900 across depths and pump types. Deep wells (300–400 ft) routinely run $2,800–$5,500+. Figures no source publishes: per-horsepower cost tables and a parts-vs-labor percentage split — omit those, never invent them.

White panel radiator on a brick wall

Boiler Replacement Cost

$3,200 – $9,000

A residential boiler replacement (equipment + labor) averages $6,100 — HomeGuide’s national figure (updated December 2025), with typical full swaps landing at $3,200–$9,000. This Old House puts equipment + labor at $4,500–$10,000; Modernize (August 2026) averages $6,500–$11,500 — its bands skew toward full installs rather than simple swaps. Gas is the most common fuel; high-efficiency/condensing models cost a clear premium. Figures no source publishes: a distinct national ‘most-pay’ figure, per-sq-ft installed pricing, and a 50% repair-vs-replace rule.

Home inspector examining a crawl space entrance

Crawl Space Encapsulation Cost

$5,000 – $15,000

Professional crawl space encapsulation averages $5,500 — Angi and This Old House (both 2026) publish the same average, with typical totals of $5,000–$15,000 (Modernize agrees, September 2026). Basic work runs $2–$4/sq ft (Angi) to $3–$7/sq ft (This Old House); extensive moisture-problem jobs reach $10/sq ft. Labor is 50–70% of the total; materials are 30–50% (Angi, This Old House).

Exposed sheet-metal air ducts and a supply register on a dark ceiling

Ductwork Replacement Cost

$1,400 – $5,600

Replacing a home’s air ducts averages $3,500 — HomeGuide’s national figure across 399 member projects (updated December 2025), with the typical range at $1,400–$5,600 by home size. This Old House (2026, Homewyse data) prices it at $16–$19 per linear foot — about $3,100–$3,700 for an average 200-foot system — and CostHelper (2026) agrees with HomeGuide’s installed band at $35–$55 per foot. No source publishes a labor-vs-materials percentage split; HomeGuide’s average is the only published national figure.

Hand adjusting a modern black smart thermostat with a Wi-Fi icon on the wall

Smart Thermostat Installation Cost

$200 – $500

A smart thermostat installed by a pro averages $300 — Fixr’s national figure (updated January 2025) for a C-wire install plus an auto-schedule smart thermostat with a two-year warranty. HomeGuide (August 2025) puts the average smart install at $225–$400; Angi (July 2026) gives the widest band, $175 to over $1,000, with the high end reserved for relocations, new wiring and multi-unit jobs. No source publishes a labor-vs-device percentage split; Fixr’s average is the only smart-only national figure.