Home › Cost Guides › Board and Batten Installation
Cost Guide

How Much Does a Board and Batten Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$7,500 – $21,300
Most homeowners pay around $12,800 · Recladding a home in board and batten siding — typically a standard 2,000 sq ft home in vinyl or fiber cement, professionally installed — typically costs $7,500–$21,300, with most homeowners paying around $12,800, about $2.50–$12.50 per sq ft installed.
typical
$7,500$21,300
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
White board-and-batten house facade against a blue sky

Board and Batten Installation cost at a glance

  • Typical range: $7,500 – $21,300
  • Most homeowners pay: around $12,800
  • Per square foot: $2.50–$12.50 per sq ft

Cross-checked against three published sources for this project. Sources used for this page: Angi, Board And Batten Siding Cost [2026 Data] (updated Sep 23, 2026, published Jul 22, 2025 — national average $12,800 for a standard 2,000-sq-ft home, most $7,500-$21,300, floor $3,000 vinyl on a smaller home, ceiling $42,000 high-end cypress on an oversized home; installed $2.50-$12.50 per sq ft; labor $1.75-$2.50 per sq ft, +10% multi-story; materials 40-90% of total; material-only cedar $1-$10, cypress $2-$21, engineered wood $3-$7, fiber cement $1.25-$15, metal $1-$20, other wood $1-$8, vinyl $3-$8 per sq ft; by home size 1,000 sq ft $9,000, 1,500 sq ft $10,900, 2,000 sq ft $12,800, 2,500 sq ft $13,900, 3,000 sq ft $15,000; removal $1,000-$3,000, paint/stain $2,000-$5,000, permits $150-$500, power washing $310+/year, repair $2-$50/sq ft, ROI 70-80% with average value bump ~$9,600); HomeGuide, How Much Does Board and Batten Siding Cost? (2026) (published Aug 1, 2023, updated Jun 23, 2025 — oldest of the set — average installed $5-$13 per sq ft; typical 2,000-sq-ft home $8,500-$22,000; by material aluminum $6-$10, cedar $6-$16, cypress $4-$16, engineered wood $7-$12, fiber cement $6-$15, steel $7-$16, vinyl $5-$9, wood $5-$15 per sq ft; material only $1-$20+ per sq ft; labor $2-$7 per sq ft; removal $0.70-$2.00 per sq ft; dumpster $280-$500/week; permits $500-$2,000; repair $2-$14 per sq ft; install time 1-2 weeks; lifespan 20-100 years by material — engineered wood 20-30, fiber cement 50-100, metal 40-70+, vinyl 30-40+, wood 20-40+; wainscoting $10-$23 per sq ft installed, interior-only band); Fixr, Board and Batten Siding Cost Guide (2026, updated Jan 26, 2026 — installed $4-$13 per sq ft, national average ~$14,000, most $7,500-$23,000, labor $1.75-$5 per sq ft, tear-off $1,000-$2,500, vinyl $4-$10, fiber cement $4-$15, metal $5-$16, engineered wood $6-$12, cedar/cypress $3-$20 per sq ft installed; by house size 2,000 sq ft home $7,200-$26,000 — FIGURES AS CITED IN MeltFlexAI's detailed reproduction of the guide, https://www.meltflexai.com/blog/board-and-batten-siding — Fixr's dedicated board-and-batten page URL was not retrievable this run, so no fixr.com URL is invented for it; corroborated by Fixr's own guides read from fixr.com: wood siding https://www.fixr.com/costs/wood-siding-installation (board and batten $5-$20 per sq ft, labor $2-$5, labor 40-60% of total), metal siding https://www.fixr.com/costs/metal-siding-installation (metal board and batten $9-$14 per sq ft), cedar siding https://www.fixr.com/costs/cedar-siding-installation (cedar board and batten $3-$20 per sq ft), fiber cement https://www.fixr.com/costs/fiber-cement-siding-installation (fiber cement board-and-batten style $6.50-$22 per sq ft, labor 40-60%)). Disagreements flagged, not averaged away: installed $/sq ft Angi $2.50-$12.50 vs HomeGuide $5-$13 vs Fixr $4-$13 (overlap $5-$12.50); permits Angi $150-$500 vs HomeGuide $500-$2,000; Angi's own other page says $4,000-$14,000 for an average-sized home vs its cost page's $7,500-$21,300 — the page leads with the cost page. Interior wainscoting is a separate scope. Worked example and shares are derived from the source ranges, not published percentages. Checked November 2026.. Sources last checked: October 2026 — HomeGuide, Fixr, Angi. How we calculate these costs

Cost by scope

Board and Batten Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Budget — Vinyl board and batten on a smaller home$3,000 – $9,000Vinyl board and batten on a smaller home (around 1,000 sq ft) — one-piece panels, the fastest install and the lowest upkeep. Angi's floor is $3,000 for vinyl on a smaller home and its 1,000 sq ft average is $9,000; vinyl runs $4–$10 per sq ft installed (Fixr) or $5–$9 (HomeGuide), with materials alone at $3–$8 (Angi).
Mid-range — Engineered wood or fiber cement, standard 2,000 sq ft home$11,000 – $22,000Engineered wood or fiber cement board and batten on a standard 2,000 sq ft home — panel plus separate batten trim, the heaviest install and the longest life (fiber cement 50–100 years, HomeGuide). Fixr's size table puts a 2,000 sq ft home at $7,200–$26,000; engineered wood runs $6–$12 per sq ft installed and fiber cement $4–$15 (Fixr), or $7–$12 and $6–$15 (HomeGuide).
Premium — Cedar, cypress or steel on a larger home$15,000 – $42,000Real cedar or cypress — or steel — on a larger home, with custom stain or finish. Angi's 3,000 sq ft average is $15,000 and its ceiling is $42,000 for high-end cypress on an oversized home; cedar runs $6–$16 per sq ft installed (HomeGuide) or $3–$20 (Fixr), cypress $4–$16 (HomeGuide), steel $7–$16 (HomeGuide).

Where the money goes

Part of the jobShareNote
Siding materials — fiber cement boards & battens, ~2,000 sq ft at ~$3.50/sq ft55% of total$7,000 — inside Angi's $1.25–$15 per sq ft fiber-cement material band. Share derived from the worked example below, not a published percentage.
Installation labor — siding crew, ~$2.00/sq ft31% of total$4,000 — inside Angi's $1.75–$2.50 per sq ft labor band and HomeGuide's $2–$7. Share derived from the worked example below, not a published percentage.
Old siding removal & disposal8% of total$1,000 — at Angi's $1,000–$3,000 floor. Share derived from the worked example below, not a published percentage.
Delivery, dumpster & cleanup4% of total$500 — inside HomeGuide's $280–$500 per week dumpster band. Share derived from the worked example below, not a published percentage.
Permits & inspection2% of total$300 — inside Angi's $150–$500 permit band; HomeGuide prices permits higher, at $500–$2,000, so a strict municipality pushes this line up. Share derived from the worked example below, not a published percentage.
Siding materials — fiber cement boards & battens, ~2,000 sq ft at ~$3.50/sq ft · 55%Installation labor — siding crew, ~$2.00/sq ft · 31%Old siding removal & disposal · 8%Delivery, dumpster & cleanup · 4%Permits & inspection · 2%
Estimator’s note: on a board and batten installation, siding materials — fiber cement boards & battens, ~2,000 sq ft at ~$3.50/sq ft is usually where quotes swing most (55% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
Board and batten started on barns like this one — wide vertical boards with battens covering the seams. Portrait source — 1200x800 centre crop keeps the barn facade and window, re-verified after processing
Board and batten started on barns like this one — wide vertical boards with battens covering the seams. Portrait source — 1200x800 centre crop keeps the barn facade and window, re-verified after processing

What moves the price most

Material choice is the biggest cost driver: vinyl runs $4–$10 per sq ft installed (Fixr) or $5–$9 (HomeGuide); engineered wood $6–$12 (Fixr) or $7–$12 (HomeGuide); fiber cement $4–$15 (Fixr) or $6–$15 (HomeGuide); cedar $3–$20 (Fixr) or $6–$16 (HomeGuide); cypress $4–$16 (HomeGuide); steel $7–$16 (HomeGuide) or $9–$14 (Fixr metal board and batten). Materials alone run $1–$10 per sq ft (Angi) and make up 40–90% of the total (Angi). Home size and stories: Angi prices by home size — 1,000 sq ft averages $9,000, 1,500 sq ft $10,900, 2,000 sq ft $12,800, 2,500 sq ft $13,900 and 3,000 sq ft $15,000 — and labor rises up to 10% on multi-story homes that need scaffolding and safety equipment (Angi). Old siding removal: Angi prices removal at $1,000–$3,000; HomeGuide at $0.70–$2.00 per sq ft (about $1,400–$4,000 on a 2,000 sq ft wall); Fixr at $1,000–$2,500. Hidden water damage or rot found underneath adds thousands more (Angi). Paint or stain: wood, engineered wood and fiber cement usually need painting or staining before or after installation, adding $2,000–$5,000 (Angi); metal needs none, and vinyl holds its colour. Budget at least $310 a year for power washing, and $2,000–$5,000 every few years to repaint or restain wood (Angi). Permits: Angi prices a siding permit at $150–$500 where the municipality requires one; HomeGuide prices permits at $500–$2,000 — a direct disagreement, so this page publishes $150–$2,000 and says it varies by municipality and job size. Labor share: the worked example's 31% labor follows Angi's own per-sq-ft figures ($1.75–$2.50 labor inside $2.50–$12.50 installed); Fixr's wood and fiber-cement guides put labor at 40–60% of the total, which reflects heavier wood and fiber-cement jobs — a scope and material difference, not an error. Interior board and batten is a different job: wainscoting runs $10–$23 per sq ft installed (HomeGuide) — MDF $7–$12, wood $12–$20 (BuildsAndBuys) — and must not be confused with the exterior siding figures above. Value and lifespan: Angi puts board and batten ROI at 70–80%, an average value bump of about $9,600; the 2025 Cost vs. Value figure of about 114% (via HomeBuddy) is fiber-cement-specific, not board-and-batten-wide. Lifespan runs 20–100 years by material (HomeGuide) — engineered wood 20–30, fiber cement 50–100, metal 40–70+, vinyl 30–40+, wood 20–40+. Install time averages 1–2 weeks (HomeGuide). Where the sources disagree: installed per-sq-ft spans are Angi $2.50–$12.50 vs HomeGuide $5–$13 vs Fixr $4–$13 — the honest overlap is $5–$12.50; Angi's $2.50 floor is cheap vinyl on small, simple jobs. Most-pay totals are Angi $7,500–$21,300 vs Fixr $7,500–$23,000 vs HomeGuide $8,500–$22,000 (2,000 sq ft home) — overlap $8,500–$21,300. National average is Angi $12,800 vs Fixr about $14,000 — no blended average is presented. Angi's own other page says $4,000–$14,000 for an average-sized home, lower than its dedicated cost page's $7,500–$21,300 — this page leads with the dedicated cost page. Worked example at the most-pay figure: a standard 2,000 sq ft home reclad in fiber cement board and batten — siding materials $7,000 + installation labor $4,000 + old siding removal and disposal $1,000 + delivery, dumpster and cleanup $500 + permits and inspection $300 = $12,800. The shares are whole-percent roundings of this worked example. For siding generally see our siding replacement guide, for vinyl see our vinyl siding installation guide, for fiber cement see our fiber cement siding installation guide, for wood see our wood siding installation guide, and for the paint that often follows see our exterior house painting guide.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A close side view of vertical boards and battens with a window — every window and door means extra cuts and trim, which is why complex walls cost more
A close side view of vertical boards and battens with a window — every window and door means extra cuts and trim, which is why complex walls cost more

Frequently asked questions

How much does board and batten siding cost per square foot?

$2.50–$12.50 per sq ft installed (Angi); HomeGuide gives $5–$13 and Fixr $4–$13, so the honest three-source overlap is $5–$12.50. Vinyl sits at the bottom of the band, cedar and cypress at the top.

What is the cheapest board and batten material?

Vinyl — $4–$10 per sq ft installed (Fixr) or $5–$9 (HomeGuide), with materials alone at $3–$8 (Angi). It is also the lowest upkeep: no painting or staining, and it holds its colour.

How long does board and batten installation take?

About 1–2 weeks on average (HomeGuide), depending on material — vinyl panels go up fastest, while fiber cement and real wood are the slowest because of the weight and cutting.

How long does board and batten siding last?

20–100 years depending on material (HomeGuide): engineered wood 20–30 years, fiber cement 50–100, metal 40–70+, vinyl 30–40+, wood 20–40+. Proper installation and maintenance decide which end you get.

Does board and batten siding add value to a home?

Partly. Angi puts ROI at 70–80% of cost, an average value bump of about $9,600. The higher figure sometimes quoted — about 114% from the 2025 Cost vs. Value report — is for fiber-cement siding replacement specifically, not board and batten generally.

How much does interior board and batten wainscoting cost?

$10–$23 per sq ft installed (HomeGuide) — MDF $7–$12, wood $12–$20 (BuildsAndBuys). That is a separate, interior-only band and must not be confused with the exterior siding figures on this page.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Board and Batten Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Stone garden patio with ivy-covered walls and stone benches

Flagstone Patio Installation Cost

$750 – $8,400

Installing a flagstone patio — typically about 200–300 sq ft, dry-laid on a compacted gravel base — typically costs $750–$8,400, with most homeowners paying around $4,500, about $15–$30 per sq ft installed.

A modern house with wood siding and a swimming pool under a blue sky

Pool House Construction Cost

$45,000 – $120,000

Building a standard custom pool house — a detached structure by the pool with a bathroom, electrical service and finished interior, roughly 180 square feet — typically costs $45,000–$120,000, with most homeowners paying around $72,000, about $150–$600 per square foot.

A formal rectangular garden pond with lily pads, framed by trimmed hedges and flowers

Pond Installation Cost

$2,900 – $5,669

Installing a backyard pond — excavating, lining, fitting a pump and filter, and edging it in stone and planting — typically costs $2,900–$5,669, with most homeowners paying around $3,382.

White louvered shutters closed over a house window, with potted plants by the door

Hurricane Shutters Installation Cost

$2,000 – $5,830

Installing hurricane shutters — permanent storm shutters fitted to the home's windows and doors, with tracks, hardware and a permit — typically costs $2,000–$5,830, with most homeowners paying around $3,635.

A minimalistic black tiny house in a forest setting

Tiny House Construction Cost

$30,000 – $60,000

Building a tiny house — a dwelling of 400 sq ft or less, finished and move-in ready — typically costs $30,000–$60,000, with most homeowners paying around $45,000. Land, site work and utility hookups are extra in every source.

An empty outdoor tennis court with seating and floodlights, seen through the fence

Tennis Court Installation Cost

$45,000 – $80,000

Building a full-size outdoor tennis court — a levelled 120 × 60 ft footprint with a concrete or asphalt base, an acrylic finish, fencing, a net and lighting — typically costs $45,000–$80,000, with most homeowners paying around $65,000.