Home › Cost Guides › Furnace Repair
Cost Guide

How Much Does a Furnace Repair Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$350 – $505
Most homeowners pay around $350 · A typical furnace repair lands at $350–$505 — the honest overlap of the three published typical ranges: HomeAdvisor (Angi) $133–$505, Fixr $150–$600 and Modernize $350–$900. Published averages disagree more than the ranges do: $318 (HomeAdvisor), $350–$400 (Fixr) and around $600 (Modernize, whose average pulls in major repairs). $350 is published here as the most-pay figure because it sits inside Fixr’s average band and just above HomeAdvisor’s; it is not a cross-source average. Major repairs run to $2,000+ and heat-exchanger replacement to $3,500.
typical
$350$505
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Technician repairing electrical equipment on a workbench, motor and wiring in hand

Furnace Repair cost at a glance

  • Typical range: $350 – $505
  • Most homeowners pay: around $350

Cross-checked against four published sources for this project. Sources used for this page: HomeAdvisor (Angi)'s furnace repair cost guide [2025 data], Fixr's HVAC service repair cost guide (2026, furnace subsection) and Modernize's furnace repair cost guide (updated August 2026). Sources last checked: October 2026 — HomeAdvisor, Modernize, Fixr, Angi. How we calculate these costs

Cost by scope

Furnace Repair cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Minor repair — sensor, thermocouple, igniter$150 – $350Modernize’s low tier: flame-sensor cleaning, a thermocouple ($100–$250) or an igniter swap ($150–$350 in the overlap) — the jobs that keep a furnace running for the price of a visit plus a small part
Standard repair — the typical band$350 – $505The overlap band itself: most routine repairs with one failed part and a few hours of labour land here, including inducer motors and control boards
Mid repair — motor, board, several parts$350 – $750Modernize’s mid tier: draft inducer motor, control board, or multiple small parts in one visit — the band where a repair visit turns into a half-day job
Major repair — variable-speed blower, heat exchanger$750 – $2,000+Modernize’s high tier: a variable-speed (ECM) blower motor ($700–$1,500) or a cracked heat exchanger ($1,500–$3,500 replacement) — at this level, compare repair against full replacement

Where the money goes

Part of the jobShareNote
Igniter$150 – $350Overlap of all three sources (HomeAdvisor $150–$500, Fixr $150–$400, Modernize $150–$350) — the most common furnace failure and the cheapest fix
Flame sensor$150 – $250Overlap of all three (HomeAdvisor $150–$250, Fixr $100–$300, Modernize $100–$300); cleaning sometimes restores it without a new part
Gas valve$300 – $600HomeAdvisor $200–$600 and Modernize $300–$600 overlap; calibration matters for safety, so this is pro-only work
Control board$400 – $600HomeAdvisor $200–$600 and Modernize $400–$800 overlap; diagnosis time is often the bigger half of this bill
Draft inducer motor$400 – $900HomeAdvisor $200–$1,500 and Modernize $400–$900 overlap; noises usually precede failure
Blower motor — PSC / ECM$450 – $1,500Modernize split: standard PSC $450–$900, variable-speed ECM $700–$1,500. HomeAdvisor’s unsplit $150–$2,000 range covers both plus repair-only cases
Heat-exchanger replacement$1,500 – $3,500Modernize $1,500–$3,500 and Fixr $1,000–$3,500+ replacement-oriented figures. HomeAdvisor’s $100 low end mixes repair-only cases with replacement and is not used here
Diagnostic visit + labour$75 – $200 visit; $75 – $150/hrDiagnostic: Fixr $75–$200 and Modernize’s inspection section $75–$150 (its labour section states a $100–$250 diagnostic minimum instead — an internal conflict). Labour $75–$150/hr is the three-source overlap. Diagnostic fees are often credited if the repair is approved
Gas-side work is pro-only: gas valves run $300–$600 in the overlap band, and a gas valve or heat-exchanger fault is a safety call, not a DIY saving
Gas-side work is pro-only: gas valves run $300–$600 in the overlap band, and a gas valve or heat-exchanger fault is a safety call, not a DIY saving

What moves the price most

The failed part is the budget: igniters and flame sensors sit at $150–$350, while motors and boards sit at $400–$1,500 and a heat exchanger at $1,500–$3,500. Motor type is the second lever — only Modernize splits it, and the split matters: a standard PSC blower is $450–$900 while a variable-speed ECM blower is $700–$1,500. Fuel type shifts the band (Modernize): gas $200–$1,200, electric $150–$900, oil $200–$1,400. Age and the repair-vs-replace threshold are genuinely unsettled across sources: HomeAdvisor and Fixr use a 50%-of-new-system rule, Modernize uses 30–40%, Fixr also states the 5,000 Rule (repair cost x age over 5,000 points to replacement), and Modernize calls repairs under $900 on a unit under 12 years old generally worth doing. Emergency timing adds 50–100% or $100–$300 (Fixr). A cracked heat exchanger is the one failure that ends the repair conversation on safety grounds, whatever the age.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
Electric heat looks different from gas heat: glowing elements, not a burner flame. Modernize prices electric furnace repairs at $150–$900 against gas at $200–$1,200 — different fuel, different band
Electric heat looks different from gas heat: glowing elements, not a burner flame. Modernize prices electric furnace repairs at $150–$900 against gas at $200–$1,200 — different fuel, different band

Frequently asked questions

How much does furnace repair cost?

The typical range is $350–$505, the overlap of HomeAdvisor (Angi) $133–$505, Fixr $150–$600 and Modernize $350–$900. Published averages run $318 (HomeAdvisor) to around $600 (Modernize); $350 is used on this page as the most-pay figure because it sits inside Fixr’s $350–$400 average band.

What is the most expensive furnace repair?

Heat-exchanger replacement at $1,500–$3,500 (Modernize; Fixr $1,000–$3,500+). It is the most expensive gas-furnace repair in every source that prices it, and a cracked exchanger is a carbon-monoxide safety issue, not just a cost question.

How much does it cost to replace a furnace igniter?

$150–$350 in the three-source overlap (HomeAdvisor $150–$500, Fixr $150–$400, Modernize $150–$350). Igniters are fragile and the most common furnace failure, which is why they sit at the cheap end of the repair range.

Should I repair or replace my furnace?

No single rule settles it: HomeAdvisor and Fixr use 50% of a new system, Modernize uses 30–40%, Fixr also states the 5,000 Rule, and Modernize calls repairs under $900 on a unit under 12 years old generally worth doing. A cracked heat exchanger, or a repair approaching half the price of a new furnace on a unit past 10–12 years, is where replacement usually wins.

How much is a furnace diagnostic visit?

$75–$200 (Fixr; Modernize’s inspection section $75–$150, though its labour section states a $100–$250 diagnostic minimum). HomeAdvisor publishes no separate diagnostic fee, noting only a trip fee of at least one hour of labour. The fee is often credited against the repair if you approve it.

Can I repair my furnace myself?

Filters, thermostat batteries and thermostat settings are safe DIY. Gas valves, igniters, control boards and anything involving combustion or a cracked heat exchanger are pro work: misdiagnosis wastes the part money, and gas and carbon-monoxide mistakes are safety failures, not just expensive ones.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Furnace Repair cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

HVAC technician kneeling beside a large outdoor unit with manifold gauges in hand

HVAC Maintenance Cost

$175 – $300

Annual HVAC maintenance typically costs $175 – $300 for a one-system plan with two seasonal tune-ups, with about $250 the figure most plans land near — Angi prices annual tune-ups at $175–$350 with a $250 average, and HomeGuide prices an annual service at $150–$300. This guide prices a maintenance plan for one system — inspection, cleaning and tune-ups for heating and cooling — not repairs, which are billed separately.

Close-up of a white finned radiator

Boiler Repair Cost

$200 – $660

A typical boiler repair lands at $200–$660 — the honest overlap of Angi’s most-pay range ($190–$660), Modernize’s typical range ($200–$1,000), Fixr’s oil-boiler repair range ($150–$750) and McQuillan Home Services’ standard repairs ($150–$750). The most-pay figure, $425, is Angi’s national average across 5,251 verified projects (updated September 2026) — the only whole-market single-point average among the independent sources. Fixr’s $450 is electric-boiler-only and is not used as a general average.

Outdoor heat pump unit standing beside a modern house

Heat Pump Repair Cost

$161 – $650

A typical air-source heat pump repair lands at $161–$650 — the honest overlap of Angi $161–$661, Fixr $150–$650 and Modernize $150–$650, a band all three sources support within $11 at each end. The most-pay figure, $400, is published as a national average by both Fixr and Modernize; Angi publishes around $410 from 4,007 verified projects (updated October 2026). Figures here are for residential air-source work only: geothermal and hybrid figures in Fixr and Modernize run higher and are not folded into the headline.

Outdoor security camera mounted above a brick wall and gate

Security System Installation Cost

$300 – $1,236

A professionally installed, monitored home security system lands at $300–$1,236 upfront, averaging $746 across 1,667 verified Angi projects (updated October 2026). That upfront figure is equipment plus installation; professional monitoring is an ongoing $20–$60 a month on top for most plans, and added cameras, sensors and smart devices — plus activation and permits — can take the all-in upfront figure toward $2,500. Homewyse's defined-scope wireless install (8 door/window contacts, 3 motion detectors, base unit and siren) at $805–$1,141 sits inside the same band, corroborating the average from a different method.

Four tall water treatment tanks with blue piping and a pressure gauge

Whole-House Water Filtration System Cost

$1,100 – $3,500

A standard whole-house water filtration system lands at $1,100–$3,500 installed — Angi's average installed band, sitting inside HomeGuide's wider $850–$5,400 spread and Dierolf Plumbing's $800–$6,000 range for professionally installed systems. About $2,000 is the most-cited average (Forbes Home's average as reported; an Angi-derived national average of $2,078 from Bob Vila lands in the same place). The tier, not the brand, decides the price: carbon filtration alone is the cheap end, adding UV and a softener moves the job up, and whole-house reverse osmosis is a separate $4,800–$8,000 category (HomeGuide) that most homes do not need.

Sunroom with wooden rocking chairs, glass doors and large windows

Sunroom Addition Cost

$20,000 – $80,000

A professionally built sunroom lands at $20,000–$80,000, the overlap of Angi's $22,000–$75,000 typical band, HomeGuide's $20,000–$80,000 four-season band and CostHelper's range up to $70,000 for a complete four-season installation. Angi's average is about $47,000, and the common installed rate is $150–$300 per sq ft inside HomeGuide's broader $100–$350 band. The season rating is the biggest lever: three-season rooms run $10,000–$40,000 while four-season rooms run $25,000–$80,000, and a fully specified custom 200 sq ft four-season build was benchmarked by Remodeling Magazine (via CostHelper) at $66,046–$83,463 — about $330–$417 per sq ft — showing how spec pushes past the general range.