Home › Cost Guides › Concrete Patio Installation
Cost Guide

How Much Does a Concrete Patio Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$2,000 – $5,000
Most homeowners pay around $3,600 · Concrete patio installation typically costs $2,000 – $5,000 for about 400 square feet (20 by 20 feet) of plain or broom-finished concrete, with about $3,600 the figure most jobs land near — Angi, updated September 23, 2026, puts the national average at $3,557 with most homeowners paying $1,919–$5,393 at $4–$30 per square foot, while HomeGuide prices a 20-by-20 plain patio at $1,600–$4,800 at $4–$12 per square foot and EngineerFix prices a standard broom-finished patio at $6–$13 per square foot. The guides agree on the plain-concrete band; the page's band is the rounded synthesis of the plain and broom bands, and decorative finishes are a separate tier, not part of the typical figure.
typical
$2,000$5,000
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Worker guiding a concrete pump hose over wet concrete

Concrete Patio Installation cost at a glance

  • Typical range: $2,000 – $5,000
  • Most homeowners pay: around $3,600
  • Prices vary most by: Labor (forming, pouring, finishing) (40–60% of the budget)

Cross-checked against two published sources for this project. Sources used for this page: Angi's concrete patio cost guide, updated September 23, 2026 (national average $3,557 across 18,358 verified projects, most $1,919–$5,393; $4–$30 per square foot installed; labor $5–$15 per square foot), HomeGuide's concrete patio cost guide (plain $4–$12, broom $6–$13, stained $8–$25, stamped $9–$30 per square foot; 20-by-20 plain $1,600–$4,800, stained or stamped $3,200–$12,000; 7-by-7 $200–$600, 30-by-30 $3,600–$10,800 plain) and EngineerFix's concrete patio cost guides (standard broom finish $6–$13 per square foot; 100 square feet $600–$1,300; materials $2–$7 per square foot; ready-mix $110–$180 per cubic yard; labor $4–$11 per square foot; single-color stain $2–$5 extra, stamping $5–$12 extra per square foot; removal $3–$10 per square foot; permits $125–$2,000; standard thickness 4 inches, 6 inches for heavy loads adding about 50% to material) — the page's typical band is the plain/broom overlap for 400 square feet, and its $3,600 most-pay figure is Angi's $3,557 national average rounded. Sources last checked: October 2026 — HomeGuide, Angi. How we calculate these costs

Cost by scope

Concrete Patio Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Small plain pad, about 100 square feet$600 – $1,300The cheap end: EngineerFix prices a standard-finish 100-square-foot patio at $600–$1,300 — a small seating pad, plain gray, broom finish
Standard 20-by-20 patio, plain or broom finish — the typical job$2,000 – $5,000The shared band itself: HomeGuide's plain 20-by-20 at $1,600–$4,800, its broom finish at $6–$13 per square foot, and Angi's most-pay band at $1,919–$5,393 — a 4-inch slab, formed, poured and broom-finished
Stamped or stained, about 400 square feet — the top end$3,200 – $12,000The expensive end: HomeGuide prices a stained or stamped 20-by-20 at $3,200–$12,000, or $9–$30 per square foot for stamped — pattern, color and sealing are what push a patio here

Where the money goes

Part of the jobShareNote
Concrete, base and reinforcement30–40% of totalThe material: EngineerFix prices the mix, sub-base gravel and reinforcement at $2–$7 per square foot, with ready-mix at $110–$180 per cubic yard delivered and rebar or mesh adding $1–$3
Labor (forming, pouring, finishing)40–60% of totalThe work: Angi prices labor at $5–$15 per square foot and puts it at 40–60% of the total in its city guides, while EngineerFix prices labor at $4–$11 — forming, pouring and the time-sensitive finish are the skilled hours
Site prep and excavation10–20% of totalThe ground: HomeGuide prices leveling a yard for a patio at $500–$1,000, and EngineerFix prices demolishing and hauling an old patio at $3–$10 per square foot
Finish, color and sealer5–15% of totalThe surface: EngineerFix prices a single-color stain at $2–$5 extra per square foot and stamping at $5–$12 extra — the finish line is small on a plain patio and the whole story on a decorative one
Concrete, base and reinforcement · 30–40%Labor (forming, pouring, finishing) · 40–60%Site prep and excavation · 10–20%Finish, color and sealer · 5–15%
Estimator’s note: on a concrete patio installation, labor (forming, pouring, finishing) is usually where quotes swing most (40–60% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
A crew pouring and finishing a slab over steel reinforcement: the mix, sub-base and reinforcement sit in the 30–40% material line, with ready-mix at $110–$180 per cubic yard in EngineerFix
A crew pouring and finishing a slab over steel reinforcement: the mix, sub-base and reinforcement sit in the 30–40% material line, with ready-mix at $110–$180 per cubic yard in EngineerFix

What moves the price most

Finish is the first fork. HomeGuide prices plain concrete at $4–$12, broom finish at $6–$13, stained at $8–$25 and stamped at $9–$30 per square foot — the same 400 square feet runs $1,600–$4,800 plain or $3,200–$12,000 decorated. Size is the second fork: HomeGuide's size table runs from $200–$600 for a 7-by-7 pad to $3,600–$10,800 for a 30-by-30 slab in plain concrete, so per-square-foot rates fall as the patio grows. Thickness is the third fork: EngineerFix notes a standard patio is poured 4 inches thick, while a 6-inch slab for a hot tub, outdoor kitchen or unstable soil adds about 50% to the material. Finally, site and permits bite: EngineerFix prices permits at $125–$2,000 depending on scope, and Angi's city guides show $185–$500 for a patio permit in New York and $200–$500 in Los Angeles.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A finished concrete surface with a drain cover: drainage, joints and sealer sit in the finish line — small on a plain patio, and the whole story on a decorative one
A finished concrete surface with a drain cover: drainage, joints and sealer sit in the finish line — small on a plain patio, and the whole story on a decorative one

Frequently asked questions

How much does a concrete patio cost per square foot?

$4–$12 for plain concrete in HomeGuide, $6–$13 for broom finish in HomeGuide and EngineerFix, and $9–$30 for stamped — Angi's full installed band runs $4–$30 across finishes.

How thick should a concrete patio be?

4 inches is the standard residential thickness in EngineerFix's guides, with 6 inches for heavier loads like a hot tub or outdoor kitchen or for unstable soil, adding about 50% to the material.

Is stamped concrete worth the extra cost?

It roughly doubles or triples the plain price in HomeGuide's table — $3,200–$12,000 for a 20-by-20 against $1,600–$4,800 plain — and buys pattern and color, not strength, so it is a looks decision, not a durability one.

Do I need a permit for a concrete patio?

It depends on the city: EngineerFix prices permits at $125–$2,000 by scope, and Angi's city guides show $185–$500 in New York and $200–$500 in Los Angeles — check the local building department before pouring.

Can I save money by doing it myself?

The labor line is $5–$15 per square foot in Angi and $4–$11 in EngineerFix, so DIY saves that share — but EngineerFix notes it needs equipment rentals and a time-sensitive finish, and a bad pour is a full replacement, not a touch-up.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Concrete Patio Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Broad concrete steps beside a house, with stone walls, green bushes and ivy

Concrete Steps Installation Cost

$1,800 – $4,500

A poured-in-place set of concrete steps, 5 to 8 steps at 4 feet wide with a standard finish — old steps removed, new steps formed, poured and finished

Worker guiding a concrete pump hose over a reinforced slab

Concrete Sidewalk Installation Cost

$1,500 – $2,800

A concrete sidewalk installation typically costs $1,500 – $2,800 for about 200 square feet of standard 4-inch concrete with a broom finish, with about $2,000 the figure most jobs land near — Angi averages $2,000 for a 200-square-foot walkway inside its $1,600–$2,400 band at about $10 per square foot, and HomeGuide averages $1,400–$3,400 at $7–$17 per square foot. The guides use walkway and sidewalk interchangeably because the materials and process are identical; the finish is what moves a job across the band, not the name.

Patio with an irregular flagstone-like pattern

Stamped Concrete Installation Cost

$3,200 – $7,600

New stamped concrete patio of about 400 sq ft, installed — about $8–$19 per sq ft for a standard pattern and color

Red-brick house with a tall chimney and white garage doors

Brick Repointing Cost

$500 – $2,500

Repointing 100 sq ft of brick wall at ground level — about $3–$20 per sq ft for walls up to 8 ft high

Stone house with a covered porch and dark double glass entry doors at dusk

Storm Door Installation Cost

$350 – $700

The typical project is one standard single storm door — full-view or self-storing, aluminum or composite — fitted to an existing, sound entry frame. Security doors, double doors and openings that need reframing are what move the job above the band.

Pool patio shaded by large white shade sails over a paved patio

Pergola Installation Cost

$2,100 – $6,400

The typical project is a standard 10-by-10-foot pergola — a kit or standard wood build — assembled and anchored on an existing patio or deck. Custom builds, large footprints and louvered roofs are what push the job above the band.