Concrete Sidewalk Installation cost at a glance
- Typical range: $1,500 – $2,800
- Most homeowners pay: around $2,000
- Prices vary most by: Labor, forming, pouring and finishing (40–55% of the budget)
Cross-checked against two published sources for this project. Sources used for this page: Angi's concrete walkway guide, updated October 28, 2026 (national average $2,000 for a 200-square-foot walkway, most $1,600–$2,400, about $10 per square foot installed; standard flat finish $8–$12, stamped $9–$23 per square foot; 100 sq ft at 4 inches $800–$1,200, 200 sq ft $1,600–$2,400; labor $50–$130 per hour; removal $2–$7 per square foot; base $1.50–$3.50 and excavation $1.50–$4 per square foot in its city guides), HomeGuide's concrete sidewalk guide (average $1,400–$3,400, $7–$17 per square foot installed; basic $7–$12, mid-range $12–$17, high-end $17–$20; replacement $10–$25+ per square foot; stamped $3–$4 extra, stained $3–$10 extra) and Networx's concrete walkway guide (basic $6–$15 per square foot, decorative to $20+; broom finish $6–$10, stamped $12–$18; labor $3–$7 per square foot). Sources last checked: October 2026 — HomeGuide, Angi. How we calculate these costs
Cost by scope

| Scope | Typical cost | What it includes |
|---|---|---|
| Small path, about 100 square feet | $800 – $1,400 | The cheap end: Angi prices a 100-square-foot sidewalk at $800–$1,200 at 4 inches thick — a short garden connection or a single straight run |
| Standard sidewalk, about 200 square feet — the typical job | $1,500 – $2,800 | The shared band itself: Angi's $2,000 average against HomeGuide's $7–$17 per square foot — standard broom finish, 4 inches thick, new install |
| Stamped or decorative sidewalk, about 200 square feet — the top end | $2,000 – $4,200 | The expensive end: HomeGuide prices stamped walkways at $10–$21 per square foot and Angi at $9–$23 — pattern, colour and borders on top of the same slab |
Where the money goes
| Part of the job | Share | Note |
|---|---|---|
| Concrete material | 25–35% of total | The mix itself: Angi puts delivered concrete at about $100 per cubic yard on a hired job, with thickness — 4 inches against 6 — deciding the volume |
| Labor, forming, pouring and finishing | 40–55% of total | The crew: Angi prices walkway labor at $50–$130 per hour, and HomeGuide puts labor at 40–60% of a sidewalk total |
| Base preparation and excavation | 10–20% of total | The ground before the pour: Angi's city guides price a gravel or sand base at $1–$4 per square foot and excavation at $1.50–$4 |
| Removal and disposal of old concrete | 5–15% of total | Only on a replacement job: Angi prices removal at $2–$7 per square foot depending on thickness — zero on a new path |

What moves the price most
Area and thickness are the first drivers. Sidewalks are priced by the square foot, and Angi's size table runs from $600–$900 for 75 square feet to $1,600–$2,400 for 200 — while 6-inch concrete for a driveway crossing costs more per foot than the standard 4-inch path. Finish is second: a broom finish is the standard $8–$12 per square foot in Angi, and stamped, stained or exposed-aggregate finishes add $3–$15 per square foot in HomeGuide before the slab itself changes. Site prep is third: a path over soft or sloping ground needs more excavation and base than one over firm, level soil, and poor drainage under a new slab is the defect that shows up as settlement later. Finally, replacement is its own line: removing and hauling an old sidewalk adds $2–$7 per square foot in Angi, which is why a replacement quote and a new-install quote for the same length are different jobs.
Costs in your city
Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

Frequently asked questions
How much does a concrete sidewalk cost?
Typically $1,500–$2,800 for about 200 square feet of standard 4-inch concrete with a broom finish, with about $2,000 the figure most jobs land near — Angi's $2,000 average for 200 square feet, against HomeGuide's $7–$17 per square foot.
How much is a concrete sidewalk per square foot?
Standard broom-finish concrete runs about $7–$14 per square foot installed across Angi and HomeGuide, with $10 a useful planning rate for a 200-square-foot job. Stamped concrete runs $9–$23 per square foot in Angi and $10–$21 in HomeGuide.
How thick should a sidewalk be?
4 inches is the standard residential thickness in both guides, and 6 inches is the step up where vehicles cross it. Thickness is priced in the concrete volume, so a 6-inch path costs more per square foot than a 4-inch path of the same length.
Do I need a permit for a sidewalk?
Often yes where the path ties into a public sidewalk or affects drainage, and some municipalities restrict decorative finishes on public-sidewalk sections. Confirm with the local building department before the pour — the permit is a small line, but a non-compliant path can be ordered removed.
How long before I can walk on a new sidewalk?
Light foot traffic is usually fine after about 24–48 hours, but concrete keeps gaining strength for weeks: keep vehicles off for at least a week and heavy loads longer, and do not rush the cure — early loading is the cheapest way to crack a new slab.






