Home › Cost Guides › Brick Repointing
Cost Guide

How Much Does Brick Repointing Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$500 – $2,500
Most homeowners pay around $1,400 · Repointing 100 sq ft of brick wall at ground level — about $3–$20 per sq ft for walls up to 8 ft high
typical
$500$2,500
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Red-brick house with a tall chimney and white garage doors

Brick Repointing cost at a glance

  • Typical range: $500 – $2,500
  • Most homeowners pay: around $1,400
  • Per square foot: $3–$20 per sq ft
  • Prices vary most by: Skilled mason labor (grind or rake out, repoint) (70–85% of the budget)

Cross-checked against two published sources for this project. Sources used for this page: Angi's repointing brick cost guide, updated October 2, 2026 (national average $1,450, most $400–$2,500 per 100 sq ft, about $14–$15 per sq ft; small patch-up minimums $300–$2,000; waterproofing $1–$4 per sq ft; brick repair $20–$40 per sq ft), HomeGuide's tuckpointing and repointing cost guide (national average $1,200, average range $500–$2,500 per 100 sq ft; $3–$20 per sq ft for walls up to 8 ft, $5–$25 above 8 ft; 8 ft by 10 ft wall $250–$1,600; minimum fees $200–$1,500; work above 8 ft costs 20–40% more; chimney tuckpointing $8–$30 per sq ft; repointing needed every 25–30 years) and EngineerFix's brick pointing cost guide ($3–$15 per sq ft, national average often cited around $8 per sq ft; labor 80–90% of the bill; minimum fees $300–$2,000). Synthesized typical = the Angi and HomeGuide 100 sq ft overlap; $1,400 most-pay sits between the two guides' averages. Checked November 2026.. Sources last checked: October 2026 — HomeGuide, Angi. How we calculate these costs

Cost by scope

Brick Repointing cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Small patch, under 100 sq ft$300 – $1,200A small section or chimney base: HomeGuide notes minimum fees of $200–$1,500 and Angi puts small patch-up minimums at $300–$2,000, so a tiny job still carries a call-out and setup charge.
Standard wall, 100 sq ft$500 – $2,500The typical project on this page. Angi's most-pay band for 100 sq ft is $400–$2,500 with a $1,450 average, and HomeGuide's average for the same area is $1,200 inside a $500–$2,500 band.
High wall, chimney or tuckpointing finish$1,200 – $3,000Work above 8 ft costs 20–40% more in HomeGuide for scaffolding, chimney tuckpointing runs $8–$30 per sq ft, and a tuckpointing finish runs $5–$25 per sq ft — the tier where height and finish move the price most.

Where the money goes

Part of the jobShareNote
Skilled mason labor (grind or rake out, repoint)70–85% of totalEngineerFix puts labor at 80–90% of the bill; repointing is hand work joint by joint, which is why the per-foot rate is mostly a labor rate
Mortar, sand and matching materials5–15% of totalMortar itself is cheap — Angi notes materials can be as little as $30 for mortar on a repair — but lime mortar for older soft brick and color matching add cost
Scaffolding, access and setup5–15% of totalHomeGuide adds 20–40% for work above 8 ft because of scaffolding; ground-level work skips this line
Cleanup, waterproofing and sealing5–10% of totalAngi prices waterproofing at $1–$4 per sq ft where it is added, and joint cleanup is part of every finished job
Skilled mason labor (grind or rake out, repoint) · 70–85%Mortar, sand and matching materials · 5–15%Scaffolding, access and setup · 5–15%Cleanup, waterproofing and sealing · 5–10%
Estimator’s note: on brick repointing, skilled mason labor (grind or rake out, repoint) is usually where quotes swing most (70–85% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
Red-brick row houses with visible mortar joints — joints like these are repointed joint by joint, which is why labor is 80–90% of the bill in EngineerFix.
Red-brick row houses with visible mortar joints — joints like these are repointed joint by joint, which is why labor is 80–90% of the bill in EngineerFix.

What moves the price most

Area is first: every guide prices by the square foot of wall, so a measured wall area is the only comparable unit — HomeGuide's 8×10 ft wall runs $240–$1,600 and Angi's 100 sq ft job runs $400–$2,500. Height is second: HomeGuide prices $3–$20 per sq ft up to 8 ft against $5–$25 above it, because scaffolding joins the job. Mortar type is third: older soft brick needs lime mortar for compatibility, not the cheapest cement mix, and a premium historic match costs more per foot in both Angi and the published breakdowns. Condition is fourth: repointing replaces mortar only — where bricks themselves are cracked or spalled, Angi prices brick repair at $20–$40 per sq ft, a separate line from the mortar work. For a new brick face rather than a repair, see our brick veneer installation guide, for chimney work, see our chimney repair guide, and for chimney tops, see our chimney cap installation guide.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A brick wall up close, courses and mortar joints prominent — repointing replaces the mortar only; bricks that are cracked or spalled are a separate repair at $20–$40 per sq ft in Angi.
A brick wall up close, courses and mortar joints prominent — repointing replaces the mortar only; bricks that are cracked or spalled are a separate repair at $20–$40 per sq ft in Angi.

Frequently asked questions

How much does brick repointing cost?

For 100 sq ft of wall at ground level, $500–$2,500 with $1,400 typical. Angi's average for the same area is $1,450 and HomeGuide's is $1,200 — the published band is the overlap of the two guides' 100 sq ft bands.

How much does repointing cost per square foot?

HomeGuide prices $3–$20 per sq ft for walls up to 8 ft and $5–$25 above that height; Angi's 100 sq ft average works out to about $14–$15 per sq ft. Small jobs cost more per foot because of minimum fees.

What is the difference between repointing and tuckpointing?

Repointing replaces failed mortar with new mortar. Tuckpointing does the same work and then adds a fine contrasting line down the center of each joint for a crisp, historic look — HomeGuide prices it at $5–$25 per sq ft, a premium finish over plain repointing.

How often does brick need repointing?

About every 25–30 years in HomeGuide, depending on exposure, mortar type and freeze-thaw cycles. Crumbling, cracked or missing mortar joints are the sign it is due, not the age of the house alone.

Can I repoint brick myself?

A small ground-level patch is a realistic DIY job if you can match the mortar — lime mortar on older soft brick is a compatibility requirement, not an upgrade. High walls, chimneys and large areas are hired work because of scaffolding and the grinding step.

What if the bricks themselves are damaged?

Repointing alone will not fix them: cracked or spalled bricks need replacing, priced at $20–$40 per sq ft in Angi's brick repair data. A quote that repoints over failing bricks is buying the same repair twice.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Brick Repointing cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Stone house with a covered porch and dark double glass entry doors at dusk

Storm Door Installation Cost

$350 – $700

The typical project is one standard single storm door — full-view or self-storing, aluminum or composite — fitted to an existing, sound entry frame. Security doors, double doors and openings that need reframing are what move the job above the band.

Pool patio shaded by large white shade sails over a paved patio

Pergola Installation Cost

$2,100 – $6,400

The typical project is a standard 10-by-10-foot pergola — a kit or standard wood build — assembled and anchored on an existing patio or deck. Custom builds, large footprints and louvered roofs are what push the job above the band.

Raised round stone-clad spa beside a backyard pool on a stamped-concrete patio

Hot Tub Installation Cost

$6,000 – $11,000

The typical project is a standard above-ground hot tub fully installed — a value-priced acrylic tub delivered and placed on a new or existing base, with a new dedicated 240-volt circuit, permits and start-up included. In-ground and custom spas are priced in the top tier.

Round tub on a brick patio in front of a house, picnic table and cushioned chairs behind

Hot Tub Repair Cost

$200 – $500

Hot tub repair typically costs $200 – $500 for a standard repair, with about $350 the figure most standard jobs land near — HomeGuide prices most minor repairs at $200–$500, Angi averages $175–$550, and Thumbtack's national range is $175–$509. This guide prices a repair visit to an existing tub, not installation and not a replacement tub.

Aerial view of a freeform inground pool with an attached round spa, stamped concrete deck and shade sails

Inground Pool Installation Cost

$45,000 – $85,000

The typical project is a standard inground pool of about 300–400 square feet — a vinyl or fiberglass pool with excavation, basic equipment, a simple concrete deck and permits included. Concrete construction, large sizes and custom features are priced in the top tier.

A small blue mosaic plunge pool with a metal ladder, set into a wooden deck

Plunge Pool Installation Cost

$10,000 – $40,000

$28,000 is Angi's published national average (updated Oct 6, 2026) — NOT a derived midpoint. HomeGuide's 2025 average is $27,500, within $500 of Angi's, and both guides top out at $40,000. Most in-ground projects land in the $15,000–$40,000 overlap of the two guides. A plunge pool is a small in-ground pool, typically 6–12 ft wide, 12–21 ft long and 4–8 ft deep, built for cooling off and soaking — not lap swimming, and not a cold-plunge tub. Above-ground pools run $3,000–$30,000; large or custom concrete in-ground pools reach $70,000–$75,000+.