Home › Cost Guides › Whole House Fan Installation
Cost Guide

How Much Does a Whole House Fan Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$900 – $2,000
Most homeowners pay around $1,500 · Whole house fan installation typically costs $900 – $2,000 for a standard home of about 2,000 square feet, with about $1,500 the most-pay figure — HomeGuide puts the national average at $1,500 inside its $600–$2,300 installed band, and Angi prices a 2,000-square-foot home at $900–$2,000 with its own average at $1,700. The $1,500 most-pay figure is HomeGuide's national average; a small direct-mount fan lands below it and a large ducted or roof-mounted system lands above it.
typical
$900$2,000
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Bright living room with hardwood floors, a grey sofa and large bay windows

Whole House Fan Installation cost at a glance

  • Typical range: $900 – $2,000
  • Most homeowners pay: around $1,500
  • Prices vary most by: Fan unit — size, type and motor (30–50% of the budget)

Cross-checked against three published sources for this project. Sources used for this page: Angi's whole-house fan cost guide (2026: national average $1,700; by home size 1,500 sq ft $800–$1,800, 2,000 sq ft $900–$2,000, 2,500 sq ft $1,000–$2,200, 3,000 sq ft $1,100–$2,400; by diameter 20 inches $600–$1,500, 30 inches $800–$1,800, 36 inches $900–$2,000; direct-drive motor materials $350–$900, belt-drive $500–$1,000; labor $300–$1,000 total or $50–$100 per hour; roof ventilation $300–$650), HomeGuide's whole-house fan installation cost guide (installed $600–$2,300, national average $1,500, minimum $450, maximum $3,000; unit $300–$1,500; labor $300–$800 using existing wiring, $600–$1,600 with a new dedicated circuit and switch; shutters $40–$200; attic fan cover $20–$40; insulation roll $20–$30; permits and inspection $50–$350; roof vent $200–$700 each; 1 square foot of venting per 450 CFM; electrician $50–$130 per hour; 4–8 hours; dedicated circuit and wall switch $250–$900; drywall repair $300–$1,500 or more; running $3–$24 per month vs central air $80–$200; overnight saving $70–$170 per month; 70–90% less energy, 120–600 watts vs 3,000–5,000 watts; QuietCool $500–$3,000 installed, $450–$1,500 unit; attic fan installed $300–$900; whole-house fan cools the home, attic fan only the attic; sizing 2–3 CFM per square foot) and Modernize's whole-house fan cost guide (unit $300–$1,500; professional installation $700–$2,000; total installed $1,200–$3,500; national average $2,000–$2,600; basic belt-drive $300–$600, direct-drive $600–$1,200, high-efficiency EC motor $900–$1,500 or more; by home size 1,000 sq ft $1,200–$2,000, 1,500 sq ft $1,500–$2,400, 2,000 sq ft $1,800–$2,800, 2,500 sq ft or more $2,200–$3,500; electrical upgrades $150–$500; additional attic venting $300–$1,000; insulated damper box $100–$300; smart thermostat or timer $75–$250; annual savings $150–$600; air conditioning use cut 50–80% in moderate climates. Sources last checked: October 2026 — HomeGuide, Modernize, Angi. How we calculate these costs

Cost by scope

Whole House Fan Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Basic direct-mount fan — small home, standard ceiling mount$600 – $1,500The cheap end: Angi prices a 20-inch fan at $600–$1,500 and HomeGuide prices the fan unit alone at $300–$1,500 — the basic belt-drive or direct-drive unit in an attic with existing wiring and adequate venting
Typical installation — the shared band$900 – $2,000The shared band itself: Angi's 2,000-square-foot band, inside HomeGuide's $600–$2,300 installed range, covering a standard fan, labor and wiring for a typical home
Large home, ducted quiet or roof-mounted system — high capacity, premium motor$1,800 – $3,500The expensive end: Modernize prices a 2,000-square-foot home at $1,800–$2,800 and a 2,500-square-foot-plus home at $2,200–$3,500, and HomeGuide prices a QuietCool system at $500–$3,000 installed — the quiet ducted and roof-mounted systems that cost more up front and run quieter

Where the money goes

Part of the jobShareNote
Fan unit — size, type and motor30–50% of totalHomeGuide prices the unit at $300–$1,500 by size and type, and Modernize prices basic belt-drive fans at $300–$600, direct-drive at $600–$1,200 and high-efficiency EC-motor fans at $900–$1,500 or more — Angi prices direct-drive motor materials at $350–$900 and belt-drive at $500–$1,000, noting belt-drive runs quieter but costs more to run
Installation labor and wiring30–50% of totalHomeGuide prices labor at $300–$800 using existing wiring or $600–$1,600 with a new dedicated circuit and switch, over 4–8 hours at $50–$130 per hour for an electrician, and Angi prices labor at $300–$1,000 total or $50–$100 per hour — a new circuit and wall switch alone runs $250–$900 at HomeGuide
Venting, shutters, cover and drywall repair10–25% of totalHomeGuide prices a roof vent at $200–$700 each, shutters at $40–$200, an attic fan cover at $20–$40 and drywall repair at $300–$1,500 or more for the ceiling opening, and Modernize prices additional attic venting at $300–$1,000, an insulated damper box at $100–$300 and a smart thermostat or timer at $75–$250
Permits and inspection5–10% of totalHomeGuide prices permits and inspection at $50–$350, required where structural or electrical wiring changes are involved — Angi likewise prices roof ventilation work that often accompanies the install at $300–$650
Fan unit — size, type and motor · 30–50%Installation labor and wiring · 30–50%Venting, shutters, cover and drywall repair · 10–25%Permits and inspection · 5–10%
Estimator’s note: on a whole house fan installation, fan unit — size, type and motor is usually where quotes swing most (30–50% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
An attic like this one is where the fan's air goes: HomeGuide requires 1 square foot of attic venting per 450 CFM of fan capacity, and prices additional attic venting at $300–$1,000 at Modernize — a fan installed without enough venting cannot move the air it is rated for
An attic like this one is where the fan's air goes: HomeGuide requires 1 square foot of attic venting per 450 CFM of fan capacity, and prices additional attic venting at $300–$1,000 at Modernize — a fan installed without enough venting cannot move the air it is rated for

What moves the price most

Home size and airflow are the first drivers: HomeGuide sizes a fan at 2–3 cubic feet per minute (CFM) per square foot of living space — a 1,500-square-foot home needs 3,000–4,500 CFM at $300–$1,200 for the unit, a 2,000-square-foot home 4,000–6,000 CFM at $350–$1,300 — and Angi prices by diameter, with a 20-inch fan at $600–$1,500, a 30-inch at $800–$1,800 and a 36-inch at $900–$2,000 installed. Motor type is second: Angi prices direct-drive motor materials at $350–$900 against belt-drive at $500–$1,000, and HomeGuide notes a belt-driven motor costs about 20% more than direct-drive — quieter, but pricier to buy and run. Attic venting is third, and it is not optional: HomeGuide requires 1 square foot of venting for every 450 CFM and prices a roof vent at $200–$700 each, while Modernize prices additional venting at $300–$1,000 — a fan without enough exhaust venting cannot move the air it promises. Climate closes the bill: a whole-house fan only cools when outside air is cooler than inside air, so Modernize lists it as most effective in California, the Pacific Northwest, the Mountain West, the Midwest and the Northeast and less effective in hot, humid climates — and it does not lower humidity, which is why HomeGuide prices running costs at just $3–$24 per month against $80–$200 for central air, with $70–$170 per month saved by running it overnight instead of the air conditioner.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A roof vent like this one is the exhaust end of the system: HomeGuide prices a roof vent at $200–$700 each, and Angi prices roof ventilation at $300–$650 — roof-mounted and ducted systems that need extra venting land at the $1,800–$3,500 end of the page, above the $900–$2,000 typical band
A roof vent like this one is the exhaust end of the system: HomeGuide prices a roof vent at $200–$700 each, and Angi prices roof ventilation at $300–$650 — roof-mounted and ducted systems that need extra venting land at the $1,800–$3,500 end of the page, above the $900–$2,000 typical band

Frequently asked questions

How much does whole house fan installation cost?

Typically $900–$2,000 for a standard home of about 2,000 square feet, with about $1,500 the most-pay figure. HomeGuide puts the national average at $1,500 inside its $600–$2,300 installed band, and Angi prices a 2,000-square-foot home at $900–$2,000 with an average of $1,700.

What is the difference between a whole-house fan and an attic fan?

What it cools. HomeGuide notes a whole-house fan cools the entire home by pulling cool outdoor air through open windows and exhausting warm air through the attic, while an attic fan only cools the attic itself — and prices attic fan installation separately at $300–$900.

What size whole house fan do I need?

HomeGuide sizes by 2–3 CFM per square foot of living space — a 1,500-square-foot home needs 3,000–4,500 CFM and a 2,000-square-foot home 4,000–6,000 CFM — and requires 1 square foot of attic venting for every 450 CFM, more where vents are screened or louvered.

Can a whole house fan replace air conditioning?

Not fully. HomeGuide notes it cannot completely replace air conditioning in hot and humid climates, and Modernize notes it works best where evening temperatures drop — it moves outdoor air, it does not refrigerate it, and it needs open windows to operate.

How much does a whole house fan cost to run?

HomeGuide prices running costs at $3–$24 per month against $80–$200 for central air, with $70–$170 per month saved by running the fan overnight instead of the air conditioner, and Modernize puts typical annual savings at $150–$600 depending on climate, electricity rates and how often the fan replaces air conditioning use.

Do I need extra attic vents for a whole house fan?

Usually yes. HomeGuide requires 1 square foot of venting per 450 CFM and prices a roof vent at $200–$700 each, and Modernize prices additional attic venting at $300–$1,000 — cutting the ceiling opening without adding exhaust vents is the install mistake that leaves the fan underperforming.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Whole House Fan Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Home theater with a large screen, wood wall and floor-standing speakers

Home Theater Installation Cost

$10,000 – $60,000

Home theater installation typically costs $10,000 – $60,000, with about $25,000 the most-pay figure — Angi puts the national average at $25,000 inside its $10,000–$60,000 band for a professional installation. The $25,000 most-pay figure is Angi's average across dedicated installations; a basic media-room setup lands far below it and a luxury custom theater lands far above it, and a lower equipment-only average from another guide is published as the disagreement, not blended.

Finished home gym room with a squat rack, barbell, bench and black rubber flooring beside sliding glass doors

Home Gym Installation Cost

$2,150 – $13,750

A professionally installed home gym in an existing room — equipment, rubber flooring and assembly together, with no structural work

Wooden home bar counter with two stools, a faucet and glassware shelves

Home Bar Installation Cost

$4,000 – $12,000

Building a home bar in a finished room — cabinetry, countertop and seating, with or without a sink; finishing the room itself priced separately

Living room with a wall-mounted TV above a fireplace, sofa and armchairs facing it

TV Mounting Cost

$150 – $350

Professional TV mounting typically costs $150 – $350 for a standard screen on drywall with the mount included, with about $250 the figure most jobs land near — Angi's 2026 data puts the national average at $149–$346, HomeAdvisor averages $255 inside $155–$355, and HomeGuide averages $275 with labor alone at $150–$400. This guide prices a pro mount-and-attach job — bracket, labor and setup — not the TV itself, and not a DIY bracket-only hang.

Wooden staircase with an ornate iron railing in a modern home interior

Stair Replacement Cost

$2,000 – $7,000

Stair replacement typically costs $2,000 – $7,000, with about $3,500 the most-pay figure — HomeGuide prices a standard replacement at $2,000–$7,000, Angi prices a full replacement at $2,000–$10,000, and Fixr's benchmark for a professionally installed red-oak straight staircase with 10 risers and two handrails is $3,563. The $3,500 most-pay figure is that Fixr benchmark rounded; a straight softwood staircase lands below it and a curved or spiral design lands far above it.

Interior staircase with a wood handrail and black metal balusters

Stair Railing Installation Cost

$900 – $3,000

Stair railing installation typically costs $900 – $3,000 for a standard straight flight with a full railing system — handrail, balusters and newel posts — with about $2,500 the figure most jobs land near — Angi's national average is $2,500 inside its $900–$6,000 most-pay band, and its straight-flight band is $900–$3,000. This guide covers interior stair railings; deck and porch railings are a separate job, covered in our deck railing guide.