Home › Cost Guides › Smoke Detector Installation
Cost Guide

How Much Does a Smoke Detector Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$70 – $150
Most homeowners pay around $120 · A smoke detector installation typically costs $70 – $150 per unit, with about $120 the most-pay figure — Angi's 2026 guide puts the national average at $120 per unit, most homeowners spending $70–$150, and Fixr's average range is the same $70–$150 with about $112 for a dual hardwired detector. HomeGuide's totals run higher at $110–$410+ per unit because its table prices smart and dual-sensor units with 1–2 hours of labor, published as-is rather than averaged away. The detector type and the wiring behind it decide the position: a battery unit on an existing ceiling is the cheap end, while a hardwired interconnected or smart system with new wiring is the expensive end.
typical
$70$150
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Worker on a ladder fitting a ceiling fixture in an empty room

Smoke Detector Installation cost at a glance

  • Typical range: $70 – $150
  • Most homeowners pay: around $120

Cross-checked against three published sources for this project. Sources used for this page: Angi's smoke detector installation cost guide (updated August 30, 2026: national average $120 per unit, most $70–$150, battery unit $10–$40 plus $20–$60 installation, hardwired $25–$60 plus $75–$150, interconnected $40–$90 plus $100–$200, smart $50–$150 plus $100–$250+, combo $30–$80 plus $60–$180, electrician $50–$100/hr, permits $25–$150, 1 detector $100–$200, 5–7 detectors $500–$1,200, 10+ detectors $1,200–$3,000+), HomeGuide's smoke detector installation cost guide (total $110–$410+ per unit, ionization $110–$290, photoelectric $120–$330, dual-sensor $140–$360+, smart $150–$410+, combo $140–$360+, CO alone $120–$360, labor $100–$260+, electrician $50–$130/hr, new breaker $150–$300, wiring $0.10–$4.00/linear foot) and Fixr's smoke detector installation cost guide (average range $70–$150, average $112 for a dual hardwired detector, low $44 battery ionization, high $398 for 3 hardwired detectors with a new base, smart material $80–$180). Sources last checked: October 2026 — HomeGuide, Fixr, Angi. How we calculate these costs

Cost by scope

Smoke Detector Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Battery-operated unit, no new wiring$30 – $100The small tier: Angi's battery unit at $10–$40 plus installation at $20–$60, combined from that guide's own components
Standard job — the typical band$70 – $150The shared band itself: Angi's most-pay band per unit, national average $120, inside Fixr's $70–$150 average range
Hardwired / interconnected / smart system$140 – $410+The expensive end: HomeGuide's dual-sensor and smart totals at $140–$360+ and $150–$410+, with new wiring and circuit work on top

Where the money goes

Part of the jobShareNote
Battery-operated detector, unit$10 – $40Angi's unit price for a battery-operated detector
Hardwired detector, unit$25 – $60Angi's unit price for a hardwired detector
Interconnected detector, unit$40 – $90Angi's unit price for an interconnected detector
Smart detector, unit$50 – $150Angi's unit price for a smart detector; Fixr prices smart material at $80–$180
Combo smoke/CO detector, unit$30 – $80Angi's unit price for a combination smoke and carbon monoxide detector
Battery-operated installation, per unit$20 – $60Angi's installation price for a battery-operated detector
Hardwired installation, per unit$75 – $150Angi's installation price for a hardwired detector
Interconnected installation, per unit$100 – $200Angi's installation price for an interconnected detector
Smart installation, per unit$100 – $250+Angi's installation price for a smart detector, subscription fees on top
Combo installation, per unit$60 – $180Angi's installation price for a combination detector
Ionization detector, total installed$110 – $290HomeGuide's total installed band for an ionization detector
Photoelectric detector, total installed$120 – $330HomeGuide's total installed band for a photoelectric detector
Dual-sensor detector, total installed$140 – $360+HomeGuide's total installed band for a dual-sensor detector
Smart detector, total installed$150 – $410+HomeGuide's total installed band for a smart detector, including Wi-Fi and security-service features
Combination smoke & CO, total installed$140 – $360+HomeGuide's total installed band for a combination detector
Carbon monoxide detector alone, total installed$120 – $360HomeGuide's total installed band for a separate CO detector
Electrician, hourly$50 – $130Angi prices electricians at $50–$100 an hour; HomeGuide at $50–$130
Handyperson, hourly$50 – $150Angi prices handypersons at $50–$150 an hour; HomeGuide at $50–$80
Installation labor, per job$100 – $260+HomeGuide's labor band for a detector installation, by complexity and pro
Fixr national average, dual hardwired detector$112Fixr's average for a dual hardwired detector, inside its $70–$150 average range
Fixr low end, battery ionization detector$44Fixr's low end for a battery-operated ionization detector
Fixr high end, 3 hardwired detectors + new base$398Fixr's high end for a set of 3 hardwired detectors with a new base
Permits$25 – $150Angi's permit band, mainly for hardwired or interconnected work and new construction
Inspection visit$50 – $100Angi's per-visit inspection band where inspections are required
New circuit breaker$150 – $300HomeGuide's band for a new circuit breaker where a separate circuit is required
New wiring, per linear foot$0.10 – $4.00HomeGuide's wiring band before labor for new hardwired runs
1 detector, studio / small condo$100 – $200Angi's total band for a single detector in a small home
2–4 detectors, apartment / condo$200 – $600Angi's total band for a small multi-detector job
5–7 detectors, single-family home$500 – $1,200Angi's total band for a typical single-family home
8–10 detectors, large / multi-story home$800 – $1,800Angi's total band for a large home
10+ detectors, estate / new build$1,200 – $3,000+Angi's total band for a large new-build or estate job
Detector repair, per unit$10 – $50Angi's band for common repairs (batteries, cleaning, minor parts); past the 50% rule, replacement wins
Extended warranty, per unit$20 – $50Angi's band for an installer's extended parts-and-labor warranty
Smart subscription, per month$5 – $10Angi's monthly band for smart-detector remote monitoring
Round white smart-home units: smart detectors run $50–$150 for the unit and $100–$250+ installed (Angi), the top tier of the detector ladder
Round white smart-home units: smart detectors run $50–$150 for the unit and $100–$250+ installed (Angi), the top tier of the detector ladder

What moves the price most

Detector type is the first driver (Angi, HomeGuide, Fixr): a battery unit at $10–$40 against hardwired at $25–$60, interconnected at $40–$90, smart at $50–$150 and combo at $30–$80 in materials alone, and installed bands that follow the same ladder — $20–$60 battery, $75–$150 hardwired, $100–$200 interconnected, $100–$250+ smart and $60–$180 combo (Angi). Wiring is second: a swap on an existing base is a short job, while a new hardwired run adds $0.10–$4.00 per linear foot (HomeGuide) plus a $150–$300 circuit breaker where a separate circuit is required, and permits at $25–$150 (Angi) where the municipality requires them. Count is third: Angi's totals run $100–$200 for one detector and $1,200–$3,000+ for 10+, but HomeGuide notes pros charge less per unit on multi-detector visits, so batching is the one real saving. Labor closes the bill: electricians at $50–$130 an hour (Angi, HomeGuide) against handypersons at $50–$150 (Angi), with a $100 minimum covering the first hour in HomeGuide's table.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
Smart-home units with a phone: smart detectors add phone alerts and voice alerts (Angi, HomeGuide), plus a $5–$10 monthly subscription (Angi)
Smart-home units with a phone: smart detectors add phone alerts and voice alerts (Angi, HomeGuide), plus a $5–$10 monthly subscription (Angi)

Frequently asked questions

How much does smoke detector installation cost?

Typically $70–$150 per unit, with about $120 the most-pay figure. Angi's 2026 guide puts the national average at $120 per unit, most homeowners spending $70–$150, and Fixr's average range is the same $70–$150 — HomeGuide's $110–$410+ totals are higher because they price smart and dual-sensor units with 1–2 hours of labor, published as-is rather than averaged away.

What is the cheapest smoke detector to install?

A battery-operated unit at $10–$40 for the detector plus $20–$60 installation (Angi), about $30–$100 combined — before any wiring, permit or inspection work, which battery units do not need.

Are hardwired smoke detectors worth the extra cost?

For most homes, yes: hardwired units at $25–$60 plus $75–$150 installation (Angi) interconnect so every alarm sounds together, carry a battery backup for outages, and are often code-required in newer homes — battery units cannot interconnect unless they use wireless technology (HomeGuide).

How many smoke detectors does a home need?

At least 5 for an average two-story, 3-bedroom home (HomeGuide): inside and outside each bedroom, on every level including the basement, and in the living room or near the stairs — the NFPA placement rule all three sources cite.

How often should smoke detectors be replaced?

Every 8–10 years (Angi, HomeGuide, Fixr), even if the alarm still sounds in tests — the sensing mechanism degrades, and Fixr notes a 10-year sealed-battery unit removes the annual battery chore in the meantime.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Smoke Detector Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Two lit crystal chandeliers hanging in a room

Chandelier Installation Cost

$350 – $1,250

A chandelier installation typically costs $350 – $1,250, with about $500 the most-pay figure — Angi's 2026 guide puts the national average at $500, most homeowners spending $350–$1,250, with labor alone at $200–$1,200 and the fixture itself at $100–$500. HomeGuide prices the whole job wider at $220–$3,400 because it separates replacement labor ($100–$350) from new-installation labor ($200–$2,000) and prices fixtures to $1,400, published as-is rather than averaged away. The fixture and the ceiling behind it decide the position: a light swap on existing wiring is the cheap end, while a heavy fixture in a new location on a high ceiling is the expensive end.

Tiled shower with a ceiling rain head and a wall-mounted head

Shower Head Installation Cost

$100 – $450

A shower head installation typically costs $100 – $450, with about $260 the most-pay figure — Angi's 2026 guide puts the national average at $260, most homeowners spending $100–$450, with labor and materials at $80–$220 per showerhead and the full project range at $75–$700. HomeGuide prices a basic shower head installation higher at $200–$900 because its shower-installation table bundles more fixture and finish work, and high-end heads with comprehensive upgrades at $650–$1,500+, published as-is rather than averaged away. The head type and the plumbing behind it decide the position: a like-for-like swap is the cheap end, while a dual, ceiling-mounted or relocated head with new plumbing is the expensive end.

Stainless kitchen sink with a gooseneck faucet against a marble backsplash

Garbage Disposal Replacement Cost

$200 – $550

A garbage disposal replacement typically costs $200 – $550, with about $450 the most-pay figure — Angi's 2026 guide puts the national average at $550, most homeowners spending $200–$625, and HomeGuide's replacement band is the same $200–$550, while Bob Vila's typical range runs wider at $150–$950 with a $400 national average. The $450 most-pay figure sits between Angi's $550 and Bob Vila's $400 averages rather than copying either one. The unit and the wiring behind it decide the position: a like-for-like swap on existing connections is the cheap end, while a larger stainless unit with new electrical work is the expensive end.

Grey outdoor air conditioner condenser on a concrete pad beside a house

Air Conditioner Installation Cost

$5,800 – $7,900

A central air conditioner installation typically costs $5,800 – $7,900, with about $5,900 the most-pay figure — Angi puts a new central AC system at $5,900 on average with installation at $1,500–$4,000, HomeGuide's standard-efficiency replacement runs $5,000–$8,300, and Fixr's installed range runs $5,800–$14,400 because it includes jobs with new ductwork. The $5,800–$7,900 band is the overlap for a standard system on existing ducts: a like-for-like change-out is the cheap end, while a larger or higher-efficiency unit with duct modifications is the expensive end.

Metal outdoor faucet on a stone wall with green leaves

Outdoor Faucet Installation Cost

$150 – $500

An outdoor faucet installation typically costs $150 – $500, with about $325 the most-pay figure — LawnLove's typical range with a $325 median, HomeGuide's hose bib replacement at $150–$350, and Angi's replacement band at $100–$300 for a standard swap, with a brand-new faucet on a new water line running $100–$4,000 in Angi's guide. A like-for-like swap on an existing line is the cheap end; a frost-free model on a new line, far from the house supply, is the expensive end.

Two people lowering a folding metal attic ladder from a ceiling hatch

Attic Ladder Installation Cost

$400 – $1,000

An attic ladder installation typically costs $400 – $1,000, with about $500 the most-pay figure — Angi puts most homeowners at around $500 or more for labor and materials with installation at $300–$1,000, HomeGuide's basic replacement at $350–$1,000, and ThePricer's standard replacement or straightforward new opening at $400–$1,000. A like-for-like swap in an existing opening is the cheap end; a new opening with framing, or a high-ceiling or heavy-duty unit, is the expensive end.