Home › Cost Guides › Garbage Disposal Replacement
Cost Guide

How Much Does a Garbage Disposal Replacement Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$200 – $550
Most homeowners pay around $450 · A garbage disposal replacement typically costs $200 – $550, with about $450 the most-pay figure — Angi's 2026 guide puts the national average at $550, most homeowners spending $200–$625, and HomeGuide's replacement band is the same $200–$550, while Bob Vila's typical range runs wider at $150–$950 with a $400 national average. The $450 most-pay figure sits between Angi's $550 and Bob Vila's $400 averages rather than copying either one. The unit and the wiring behind it decide the position: a like-for-like swap on existing connections is the cheap end, while a larger stainless unit with new electrical work is the expensive end.
typical
$200$550
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Stainless kitchen sink with a gooseneck faucet against a marble backsplash

Garbage Disposal Replacement cost at a glance

  • Typical range: $200 – $550
  • Most homeowners pay: around $450

Cross-checked against three published sources for this project. Sources used for this page: Angi's garbage disposal replacement cost guide (updated October 13, 2026: national average $550, most $200–$625, units $50–$400 by motor size, 1/3–1/2 HP $50–$225, 5/8–3/4 HP $120–$310, 1–1-1/4 HP $200–$400, labor $50–$100/hr about an hour, corroded-unit extra up to $100, continuous feed $75–$1,000, batch feed $75–$300, aluminum $75–$300, stainless $400–$1,100, DIY floor $75, lifespan 5–10 years, stainless to 15), HomeGuide's garbage disposal installation cost guide (replacement $200–$550, removal $25–$50, unit $100–$300, install labor $75–$200, total labor $100–$250, handyman $80–$160, plumber $100–$250, Home Depot labor $120–$150, Lowe's $150–$200, outlet $150–$350, drain mods $100–$350, permits $50–$350 electrical and $30–$500 plumbing, new retrofit $250–$650, repair $100–$250, 1–3 hours replacement, lifespan 8–12 years) and Bob Vila's garbage disposal installation cost guide (typical $150–$950, national average $400, labor $150–$350, DIY project $150–$200, replacement $250–$400 in its repair guide). Sources last checked: October 2026 — HomeGuide, Angi, Home Depot. How we calculate these costs

Cost by scope

Garbage Disposal Replacement cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
DIY like-for-like unit swap$75 – $200The small tier: Angi's skilled-DIYer floor of $75 and Bob Vila's $150–$200 DIY project estimate, unit only on existing connections
Standard job — the typical band$200 – $550The shared band itself: Angi's most-pay band and HomeGuide's $200–$550 replacement band, including removal, unit and labor
Premium unit or new electrical work$550 – $1,100The expensive end: Angi's stainless-steel units at $400–$1,100 plus labor, and first-time installations needing a new circuit

Where the money goes

Part of the jobShareNote
Replacement total, Angi$200 – $625Angi's most-pay band for a professional garbage disposal replacement, national average $550
Replacement total, HomeGuide$200 – $550HomeGuide's replacement band including removal, mounting, connections, testing and cleanup
Typical range, Bob Vila$150 – $950Bob Vila's typical range for garbage disposal installation, national average $400
New unit only, HomeGuide$100 – $300HomeGuide's unit price before labor; its size table runs 1/3 HP $75–$125 to 1.0 HP $175–$400
1/3–1/2 HP unit, Angi$50 – $225Angi's unit band for small-household motors
5/8–3/4 HP unit, Angi$120 – $310Angi's unit band for mid-size motors
1–1-1/4 HP unit, Angi$200 – $400Angi's unit band for large-household motors
Continuous-feed unit, Angi$75 – $1,000Angi's continuous-feed unit band; HomeGuide prices continuous-feed at $75–$300 for 1/2–3/4 HP
Batch-feed unit, Angi$75 – $300Angi's batch-feed unit band; HomeGuide prices batch-feed at $200–$350 for 1/2–3/4 HP
Aluminum unit, Angi$75 – $300Angi's aluminum unit band, lifespan under 10 years
Stainless-steel unit, Angi$400 – $1,100Angi's stainless-steel unit band, lifespan up to 15 years
Old unit removal, HomeGuide$25 – $50HomeGuide's removal band inside a replacement job; permanent removal alone runs $125–$350
Installation labor, HomeGuide$75 – $200HomeGuide's installation-labor band inside the replacement total
Total labor to replace, HomeGuide$100 – $250HomeGuide's total labor band for a replacement, by pro type
Labor, Angi$50 – $100 per hourAngi's hourly band, most jobs about an hour
Labor, Bob Vila$150 – $350Bob Vila's labor band for installing a garbage disposal
Handyman labor, HomeGuide$80 – $160HomeGuide's handyman labor band for a replacement, based on 2 hours
Plumber labor, HomeGuide$100 – $250HomeGuide's plumber labor band for a replacement, based on 2 hours
Home Depot labor$120 – $150HomeGuide's Home Depot labor-only band for a replacement under favorable conditions
Lowe's labor$150 – $200HomeGuide's Lowe's labor-only band for a replacement under favorable conditions
Corroded-unit extra, Angiup to $100Angi's extra charge where a corroded unit will not budge
New electrical outlet, HomeGuide$150 – $350HomeGuide's outlet band where no suitable outlet exists
Drain pipe modifications, HomeGuide$100 – $350HomeGuide's band for sink drain pipe work during installation
Electrical permit, HomeGuide$50 – $350HomeGuide's permit band for a new outlet or wiring upgrade
Plumbing permit, HomeGuide$30 – $500HomeGuide's permit band for new pipework where none existed
New retrofit total, HomeGuide$250 – $650HomeGuide's total for installing where a disposal did not exist
Repair total, HomeGuide$100 – $250HomeGuide's repair band; Bob Vila prices replacement at $250–$400 in its repair guide, the 50% rule deciding between the two
Replacement time, HomeGuide1 – 3 hoursHomeGuide's time band for a replacement; a first-time install takes 2–4 hours or more
Lifespan, Angi / HomeGuide5 – 12 yearsAngi prices lifespan at 5–10 years (stainless to 15); HomeGuide at 8–12 years
Under-sink drain pipes and filtration tanks: this is the work zone for a replacement — removal runs $25–$50 inside the job (HomeGuide), and a corroded unit can add up to $100 in extra labor (Angi)
Under-sink drain pipes and filtration tanks: this is the work zone for a replacement — removal runs $25–$50 inside the job (HomeGuide), and a corroded unit can add up to $100 in extra labor (Angi)

What moves the price most

Motor size is the first driver (Angi, HomeGuide): a 1/3–1/2 HP unit at $50–$225 against 5/8–3/4 HP at $120–$310 and 1–1-1/4 HP at $200–$400 (Angi), with HomeGuide's size table running the same ladder from $75–$125 to $175–$400. Material and feed type are second: aluminum at $75–$300 against stainless steel at $400–$1,100 (Angi), and continuous-feed at $75–$1,000 against batch-feed at $75–$300 (Angi) — batch-feed costs more per unit in HomeGuide's 1/2–3/4 HP table ($200–$350) but is safer around children. Who does it is third: handyman labor at $80–$160 against plumber labor at $100–$250 (HomeGuide), and big-box labor at $120–$200 before the unit (HomeGuide). Existing connections close the bill: a like-for-like swap reuses the outlet and drain, while a first-time install adds an outlet at $150–$350, drain work at $100–$350 and permits at $30–$500 (HomeGuide).

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A kitchen island sink running: a like-for-like swap takes 1–3 hours (HomeGuide), while a first-time install with new electrical work takes 2–4 hours or more
A kitchen island sink running: a like-for-like swap takes 1–3 hours (HomeGuide), while a first-time install with new electrical work takes 2–4 hours or more

Frequently asked questions

How much does garbage disposal replacement cost?

Typically $200–$550, with about $450 the most-pay figure. Angi's 2026 guide puts the national average at $550, most homeowners spending $200–$625, and HomeGuide's replacement band is the same $200–$550 — Bob Vila's $150–$950 typical range with a $400 average is wider because it covers first-time installs too, published as-is rather than averaged away.

What is the cheapest garbage disposal to replace?

A small aluminum continuous-feed unit: Angi prices 1/3–1/2 HP units at $50–$225 and aluminum at $75–$300, with a skilled DIYer getting a new unit in for as little as $75 on existing connections — HomeGuide's removal band alone is $25–$50 inside a pro replacement.

Is it better to repair or replace a garbage disposal?

Replace when the repair passes half the replacement price or the unit is over 8 years old (HomeGuide): repairs run $100–$250 against a $200–$550 replacement, and Bob Vila prices replacement at $250–$400 in its repair guide — a unit that will not turn on, leaks from internal cracks, or needs frequent resets is a replacement (Angi).

How long does a garbage disposal replacement take?

1–3 hours for a like-for-like replacement (HomeGuide), about an hour in Angi's estimate — a first-time install where no disposal existed takes 2–4 hours or more because of the new electrical and plumbing work.

Can I replace a garbage disposal myself?

Yes on a like-for-like swap with existing wiring and pipes in good condition (HomeGuide, Bob Vila): Bob Vila prices the DIY project at $150–$200 and about 2 hours, but changing the model type, moving the unit, or adding electrical or plumbing work is pro work — and a corroded unit can add up to $100 in extra labor (Angi).

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Garbage Disposal Replacement cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Grey outdoor air conditioner condenser on a concrete pad beside a house

Air Conditioner Installation Cost

$5,800 – $7,900

A central air conditioner installation typically costs $5,800 – $7,900, with about $5,900 the most-pay figure — Angi puts a new central AC system at $5,900 on average with installation at $1,500–$4,000, HomeGuide's standard-efficiency replacement runs $5,000–$8,300, and Fixr's installed range runs $5,800–$14,400 because it includes jobs with new ductwork. The $5,800–$7,900 band is the overlap for a standard system on existing ducts: a like-for-like change-out is the cheap end, while a larger or higher-efficiency unit with duct modifications is the expensive end.

Metal outdoor faucet on a stone wall with green leaves

Outdoor Faucet Installation Cost

$150 – $500

An outdoor faucet installation typically costs $150 – $500, with about $325 the most-pay figure — LawnLove's typical range with a $325 median, HomeGuide's hose bib replacement at $150–$350, and Angi's replacement band at $100–$300 for a standard swap, with a brand-new faucet on a new water line running $100–$4,000 in Angi's guide. A like-for-like swap on an existing line is the cheap end; a frost-free model on a new line, far from the house supply, is the expensive end.

Two people lowering a folding metal attic ladder from a ceiling hatch

Attic Ladder Installation Cost

$400 – $1,000

An attic ladder installation typically costs $400 – $1,000, with about $500 the most-pay figure — Angi puts most homeowners at around $500 or more for labor and materials with installation at $300–$1,000, HomeGuide's basic replacement at $350–$1,000, and ThePricer's standard replacement or straightforward new opening at $400–$1,000. A like-for-like swap in an existing opening is the cheap end; a new opening with framing, or a high-ceiling or heavy-duty unit, is the expensive end.

Modern white house with large panes of glass across two floors and glass balcony rails

Window Glass Replacement Cost

$300 – $650

Replacing the glass in one standard window typically costs $300 – $650, with about $375 the most-pay figure — HomeGuide's average range is $300–$650 with a $475 national average, Fixr's national average is $375 inside a $300–$880 range, and Angi's average is lower at $285 because its project mix skews toward standard double-pane units, where most homeowners pay $181–$414. The $300–$650 band is the honest middle for a standard installed job: a single pane is cheaper, and a large, triple-pane or specialty window is dearer.

Room with a flooded tiled floor reflecting a window, and damp staining on the wall

Water Damage Restoration Cost

$1,400 – $6,400

Water damage restoration typically costs $1,400 – $6,400, with about $3,900 the most-pay figure — Angi puts the average at $3,868 with most homeowners paying $1,383–$6,369, Modernize puts the average near $3,900 on a $1,300–$6,500 band, and HomeGuide prices extraction alone at $4–$12 per square foot by water category. The $3,900 most-pay figure sits where Angi's and Modernize's averages meet; a small clean-water job lands well below it and black-water or whole-home flooding lands far above it.

A leaking outdoor water pipe spraying water

Leak Detection Cost

$150 – $400

Professional leak detection typically costs $150 – $400 for a standard hidden-leak visit, with about $300 the figure most visits land near — Angi prices detection at $100–$500, and HomeGuide prices a plumber's leak detection test at $100–$400. This guide prices finding the leak only — diagnosis, location and a written report — not the repair, which is quoted once the leak is located.