Pocket Door Installation cost at a glance
- Typical range: $800 – $2,500
- Most homeowners pay: around $1,050
- Prices vary most by: Installation labor (35–50% of the budget)
Cross-checked against four published sources for this project. Sources used for this page: Angi's pocket door cost guide, updated Oct 29, 2026 (installation $800–$2,500, national average $1,050; single retrofit $1,550–$2,950; single new construction $550–$1,850; double retrofit $1,700–$4,200; French retrofit $2,500–$7,000; contractor $350–$600 for a standard six-hour install), HomeGuide's interior door installation cost guide (pocket installation $500–$2,500 including parts and labor; cheap kits from $80, about $450 installed; high-end steel frame kit with wood door and handles $1,800; pocket door material alone up to $5,000), ThePricer's pocket door installation cost guide (typical single $800–$2,500, average about $1,050; Homewyse basic $1,112–$1,705; basic 2-by-4 wall frame kit near $114–$200 retail; solid wood $600–$2,200 installed, hollow-core or glass $500–$2,350, per Angi data cited there).. Sources last checked: October 2026 — HomeGuide, Angi, ThePricer, Homewyse. How we calculate these costs
Cost by scope

| Scope | Typical cost | What it includes |
|---|---|---|
| New-construction single — the budget route | $550 – $1,850 | The cheap end: Angi prices a single pocket door at $550–$1,850 when the wall is still open, because the frame kit goes in before drywall and no demolition or making-good is needed — the same door in an existing wall costs more for the wall work alone |
| Retrofit single, standard — the typical job | $800 – $2,500 | The shared band itself: Angi prices a standard single retrofit in this band with a $1,050 average, and HomeGuide prices pocket installation at $500–$2,500 including parts and labor — one door sliding into a prepared wall cavity in an existing home, which is the common job and the band this page is built on |
| Double, French or premium — the top end | $1,700 – $4,200 | The expensive end: Angi prices a double pocket door retrofit at $1,700–$4,200 and a French pocket retrofit at $2,500–$7,000 — two leaves, wider framing, heavier hardware and more finishing, which is what pushes a job past the single-door band |
Where the money goes
| Part of the job | Share | Note |
|---|---|---|
| Door, frame kit and hardware | 30–40% of total | The parts: ThePricer prices a basic 2-by-4 wall pocket frame kit near $114–$200 at retail, HomeGuide prices a high-end steel frame kit with a wood door and handles at $1,800 installed, and Angi notes solid wood doors at $600–$2,200 installed against hollow-core or glass at $500–$2,350 — the door material is what moves this line most |
| Installation labor | 35–50% of total | The largest portion on a retrofit: Angi prices a contractor at $350–$600 for a standard six-hour installation, and notes the figure climbs where demolition, electrical work or plumbing is involved — opening the wall, setting the frame plumb and hanging the door is the skilled work |
| Drywall, trim and paint | 15–25% of total | The making-good: a retrofit opens one side of the wall, and the patch, corner beads, trim and paint that return it to a finished wall are a real share of the bill — a new-construction install skips most of this line, which is the main reason it prices lower |
| Rerouting and permits | 5–15% of total | The surprise line: HomeGuide notes wiring and pipes in the wall must be moved before the pocket goes in, and ThePricer notes permits can be part of the total where structural or electrical work is involved — a wall with a switch, outlet or supply pipe pays this line, a clear partition wall does not |

What moves the price most
Retrofit versus new construction is the first driver: Angi prices a single pocket door at $550–$1,850 in new construction against $1,550–$2,950 as a retrofit, because a retrofit opens a finished wall, removes studs and makes the wall good again, while new construction sets the frame before drywall exists. What is inside the wall is second: HomeGuide notes that wiring and pipes in the way must be moved, and Angi notes labor climbs where demolition, electrical or plumbing work is required — a load-bearing wall adds a header and engineering on top. Door type and material are third: Angi's retrofit table runs from a single at $1,550–$2,950 through a double at $1,700–$4,200 to French at $2,500–$7,000, and its material notes put solid wood at $600–$2,200 installed against hollow-core or glass at $500–$2,350. Finally, hardware quality closes the bill: a pocket door lives or dies by its track and rollers, and the heavy-duty kits that carry a solid door smoothly for years cost more than the basic kit — the cheapest line on the quote is the one you feel every day.
Costs in your city
Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

Frequently asked questions
How much does it cost to install a pocket door?
Most standard single doors land in the $800–$2,500 band on this page, with a common middle around $1,050 — Angi's October 2026 average. HomeGuide prices pocket installation at $500–$2,500 including parts and labor, and Homewyse puts a basic install at $1,112–$1,705 for favorable site conditions.
Why is a pocket door cheaper in new construction?
Because the wall is open: Angi prices a single pocket door at $550–$1,850 in new construction against $1,550–$2,950 as a retrofit. A retrofit pays for demolition, stud removal, drywall patching, trim and paint that new construction never needs — the door and kit cost the same either way.
Can any wall take a pocket door?
No — the wall must have a clear cavity as wide as the door plus its frame, and HomeGuide notes wiring and pipes in the way must be moved first. A load-bearing wall needs a header to carry the load above, and a wall thinner than the frame kit, or one packed with plumbing, may not take a pocket at all — the wall check comes before the door is ordered.
Pocket door or barn door — which costs less?
A barn door, usually: this site's barn door page prices a standard single interior barn door at $400–$1,500 with most near $1,000, against $800–$2,500 here, because a barn door mounts on the wall face while a pocket door needs the wall opened and remade. A pocket door earns the premium where floor space is tight and a swinging or surface-mounted door would block furniture or traffic.
Can I install a pocket door myself?
A confident DIYer can, on a clear non-load-bearing wall: ThePricer prices a basic frame kit near $114–$200 at retail, and the job is framing, hanging and finishing rather than specialist work. The risks are a frame set out of plumb, which makes the door drag for its whole life, and any wiring or plumbing found in the wall — most homeowners hand those parts to a pro, and Angi prices a contractor at $350–$600 for a standard six-hour install.






