Home › Cost Guides › Chain-Link Fence Installation
Cost Guide

How Much Does a Chain-Link Fence Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$1,300 – $3,600
Most homeowners pay around $2,400 · Chain-link fence installation typically costs $1,300 – $3,600 for a standard residential run of about 150 linear feet, at about $10–$25 per linear foot installed, with about $2,400 the figure most jobs land near — Angi averages $2,420 across 3,993 verified projects with most at $1,297–$3,588, HomeGuide prices 150 feet at $1,500–$6,000 at $10–$40 per linear foot, and Fixr prices 100 linear feet of 11-gauge galvanized fence at $1,489–$2,771. A short 4-foot galvanized run lands below the band, and a taller vinyl-coated fence with gates runs above it, while the mesh, posts, rails, labor, gates and permits below are all inside the total.
typical
$1,300$3,600
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Close-up of a chain-link fence against a clear blue sky

Chain-Link Fence Installation cost at a glance

  • Typical range: $1,300 – $3,600
  • Most homeowners pay: around $2,400
  • Prices vary most by: Mesh, posts, rails and concrete (40–50% of the budget)

Cross-checked against three published sources for this project. Sources used for this page: Angi's chain-link fence cost guide, updated September 30, 2026 (national average $2,420 across 3,993 verified projects, most $1,297–$3,588; $8–$40 per linear foot, most $10–$20; 4-foot $8–$20, 6-foot $10–$29, 8-foot $12–$34, 10-foot $17–$40; labor about 50% of the total, around $1,300 on the average job; posts about $3 per linear foot), HomeGuide's chain-link fence cost guide ($10–$40 per linear foot installed, $1,500–$6,000 for 150 feet; labor $5–$20 per linear foot, about half the total; 4-foot $10–$20, 6-foot $13–$30+, 8-foot $20–$40+; galvanized $10–$40, black vinyl-coated $10–$34; lifespan 15–20 years) and Fixr's chain-link fence cost guide (100 linear feet of 11-gauge galvanized steel $1,489–$2,771; 50 linear feet of 4-foot 11-gauge from $654; 200 linear feet of 6-foot 9-gauge to $8,367; permits averaging $75; a gate about $100 extra). Sources last checked: October 2026 — HomeGuide, Fixr, Angi. How we calculate these costs

Cost by scope

Chain-Link Fence Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Budget 4-foot galvanized — the low end$1,000 – $2,000The cheap end: HomeGuide prices a 4-foot chain-link fence at $10–$20 per linear foot installed, and Fixr prices 50 linear feet of 4-foot 11-gauge galvanized fence from $654 — a short, plain galvanized run for a front yard or a dog run
Standard 6-foot galvanized — the typical job$1,300 – $3,600The shared band itself: Angi prices most chain-link jobs at $1,297–$3,588 with an average of $2,420, HomeGuide prices a 6-foot fence at $13–$30+ per linear foot, and Fixr prices 100 linear feet at $1,489–$2,771
Premium vinyl-coated, taller or gated — the top end$3,600 – $6,000The expensive end: HomeGuide prices black vinyl-coated chain-link at $10–$34 per linear foot and 150 feet up to $6,000, and Fixr prices 200 linear feet of 6-foot 9-gauge galvanized fence at $8,367 — height, heavier gauge, coating, privacy slats and gates push a job here

Where the money goes

Part of the jobShareNote
Mesh, posts, rails and concrete40–50% of totalThe fence itself: HomeGuide prices chain-link materials at $5–$20 per linear foot by height, and Angi prices posts at about $3 per linear foot — galvanized mesh is the budget choice, vinyl-coated costs more
Installation labor40–50% of totalThe setting: Angi puts labor at about half the total, around $1,300 on its average job, and HomeGuide prices labor alone at $5–$20 per linear foot — digging, setting posts in concrete and stretching the mesh straight
Gates, permits and extras10–20% of totalThe rest: Fixr prices a gate at about $100 extra in its guide and permits at an average of $75, while privacy slats, a second gate or clearing an old fence are priced on top
Mesh, posts, rails and concrete · 40–50%Installation labor · 40–50%Gates, permits and extras · 10–20%
Estimator’s note: on a chain-link fence installation, mesh, posts, rails and concrete is usually where quotes swing most (40–50% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
Chain-link fence at a sports field at sunset: height is the first price driver — Angi prices a 4-foot fence at $8–$20 and a 6-foot fence at $10–$29 per linear foot
Chain-link fence at a sports field at sunset: height is the first price driver — Angi prices a 4-foot fence at $8–$20 and a 6-foot fence at $10–$29 per linear foot

What moves the price most

Height is the first driver: Angi prices a 4-foot chain-link fence at $8–$20 per linear foot, a 6-foot fence at $10–$29, an 8-foot fence at $12–$34 and a 10-foot fence at $17–$40 — every extra foot is more mesh, taller posts and more concrete. Length is second: the whole job is per-foot maths, so a 150-foot run at HomeGuide's $10–$40 lands at $1,500–$6,000 before gates, and a short run pays the crew's minimum even at a low per-foot rate. Gauge and coating are third: Fixr's 11-gauge galvanized is the standard residential mesh, 9-gauge is the heavier commercial grade, and HomeGuide prices black vinyl-coated mesh at $10–$34 per linear foot for a cleaner look that also resists rust. Finally, gates, slope and the old fence close the bill: Fixr prices a gate at about $100 extra and permits at an average of $75, and a slope, rocky ground or an old fence to haul away is priced on top of the run itself.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A chained gate: gates are priced on top of the fence run — Fixr prices a gate at about $100 extra, and permits at an average of $75
A chained gate: gates are priced on top of the fence run — Fixr prices a gate at about $100 extra, and permits at an average of $75

Frequently asked questions

How much does a chain-link fence cost?

About $1,300–$3,600 for a standard residential run of about 150 linear feet, with about $2,400 the common middle. Angi averages $2,420 across 3,993 verified projects, most at $1,297–$3,588.

How much does a chain-link fence cost per linear foot?

HomeGuide prices it at $10–$40 per linear foot installed across heights, and Angi prices most jobs at $10–$20 — the typical band on this page is $10–$25. Height sets the rung: Angi prices 4-foot at $8–$20, 6-foot at $10–$29 and 8-foot at $12–$34 per linear foot.

Galvanized or vinyl-coated chain-link — which should I choose?

Galvanized is the budget choice: HomeGuide prices it at $10–$40 per linear foot, it resists rust and it is the most widely available mesh. Black vinyl-coated mesh, at $10–$34 in HomeGuide, costs a little more for a cleaner, less industrial look and an extra layer against rust — the fence underneath is the same steel either way.

How long does a chain-link fence last?

HomeGuide's chain-link table puts the lifespan at 15–20 years. Galvanized mesh resists rust on its own, and the posts and rails usually decide the real life of the fence — posts set in concrete and kept clear of soil and standing water last the longest.

Do I need a permit, and what does a gate add?

Check with the city first: Fixr prices permits at an average of $75, but the fee and the height rules vary by jurisdiction. A gate is priced on top of the run — Fixr prices a gate at about $100 extra in its guide — and a wide driveway gate costs more than a walk gate.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Chain-Link Fence Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Tall vertical-board wooden fence with pointed tops

Wood Fence Installation Cost

$3,750 – $5,500

Wood fence installation typically costs $3,750 – $5,500 for 150 linear feet of 6-foot wood privacy fence, at about $25–$37 per linear foot installed, with about $4,500 the figure most jobs land near — HomeGuide prices a 6-foot wood privacy fence at $25–$50 per linear foot, Fixr prices a wood privacy fence at $17–$37 installed with an average job of $4,500, and Angi averages $3,312 across all wood fence styles with most at $1,919–$4,948. A picket or split-rail fence lands below the band, and cedar or redwood with gates and stain runs above it, while the lumber, posts, labor, gates and finish below are all inside the total.

Ornate black metal double gate with scrollwork

Wrought Iron Fence Installation Cost

$5,000 – $8,500

Wrought iron fence installation typically costs $5,000 – $8,500 for about 100 linear feet of 4-foot fence, installed, with about $6,750 the figure most jobs land near — HomeGuide prices wrought iron at $50–$85 per linear foot installed for 4–6-foot heights and puts a 100-foot run at $5,000–$8,500, while Angi, updated September 11, 2026, averages $3,169 across 1,659 verified projects with most paying $1,421–$5,138 and prices materials for a typical 4-foot fence at $25–$35 per linear foot; and Fixr averages $22–$40 per linear foot installed. Angi's length table is material-led and HomeGuide's band is full installed — the gap is published here as a scope split, not averaged away — and this page's typical band follows HomeGuide's installed scope, with $6,750 the midpoint of that 100-foot band rather than a guide-stated average. The iron panels, posts, labor, gates and columns below are all inside the total for a standard installed run, while automated gates — Angi prices them from $600 for a small manual gate to over $8,500 for an automated driveway gate — and brick columns at $450–$1,275 each are tiered and published separately.

Green powder-coated metal fence panel with a post

Aluminum Fence Installation Cost

$3,750 – $6,800

Aluminum fence installation typically costs $3,750 – $6,800 for about 150 linear feet of standard 4-foot picket fencing, with about $4,600 the figure most jobs land near — Angi, updated September 23, 2026, puts the national average at $4,607 with most homeowners paying $2,426–$6,791 and prices a complete project at $22–$72 per linear foot, while HomeGuide prices a 150-foot picket, pool or ornamental run at $3,750–$11,250 at $25–$75 per linear foot and EngineerFix prices a professionally installed black aluminum fence at $22–$72 per linear foot turnkey. The guides agree on the per-foot band; where they differ is scope — Angi's length table runs to 300 feet and HomeGuide's privacy tier runs to $130 per foot — so this page's typical band follows the standard picket overlap for 150 feet, with split-rail, ornamental and privacy tiers published separately.

Two-story gray house at dusk with a wide concrete driveway and three garage doors

Concrete Driveway Cost

$3,500 – $8,600

Typical 2-car driveway of about 576 sq ft in plain concrete, installed — about $6 – $15 per sq ft installed

Car parked in a snowy driveway beside a white house in winter

Heated Driveway Installation Cost

$7,500 – $15,000

A heated driveway installation typically costs $7,500 – $15,000 for a standard two-car driveway of about 600 sq ft, with about $13,000 the figure most standard jobs land near — Angi prices heated driveway installation at $12–$25 per sq ft with an average near $13,000, HomeGuide prices a heated concrete or asphalt driveway at $12–$28 per sq ft with a $14,600 national average and a $6,900–$22,400 average range, and HouseDigest puts the same work at $12–$28 per sq ft with a two-car driveway reaching about $16,000. The $7,500–$15,000 typical band is the $12–$25 per sq ft overlap applied to about 600 sq ft, and $13,000 is Angi's average — a mat-only job can come in far below it, and a hydronic system under pavers costs far more, while the heating system, surface, labor and controls below are all inside the total.

Single-story beige stucco house with a freshly painted exterior, neat lawn and concrete walkway

Exterior House Painting Cost

$3,000 – $7,500

Typical full exterior of an average home, washed, prepped and painted — about $1.50 – $4 per sq ft of paintable surface