Home › Cost Guides › Wrought Iron Fence Installation
Cost Guide

How Much Does a Wrought Iron Fence Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$5,000 – $8,500
Most homeowners pay around $6,750 · Wrought iron fence installation typically costs $5,000 – $8,500 for about 100 linear feet of 4-foot fence, installed, with about $6,750 the figure most jobs land near — HomeGuide prices wrought iron at $50–$85 per linear foot installed for 4–6-foot heights and puts a 100-foot run at $5,000–$8,500, while Angi, updated September 11, 2026, averages $3,169 across 1,659 verified projects with most paying $1,421–$5,138 and prices materials for a typical 4-foot fence at $25–$35 per linear foot; and Fixr averages $22–$40 per linear foot installed. Angi's length table is material-led and HomeGuide's band is full installed — the gap is published here as a scope split, not averaged away — and this page's typical band follows HomeGuide's installed scope, with $6,750 the midpoint of that 100-foot band rather than a guide-stated average. The iron panels, posts, labor, gates and columns below are all inside the total for a standard installed run, while automated gates — Angi prices them from $600 for a small manual gate to over $8,500 for an automated driveway gate — and brick columns at $450–$1,275 each are tiered and published separately.
typical
$5,000$8,500
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Ornate black metal double gate with scrollwork

Wrought Iron Fence Installation cost at a glance

  • Typical range: $5,000 – $8,500
  • Most homeowners pay: around $6,750
  • Prices vary most by: Iron panels and posts (plain, galvanized or ornamental) (40–55% of the budget)

Cross-checked against three published sources for this project. Sources used for this page: Angi's wrought iron fence installation guide, updated September 11, 2026 (national average $3,169 across 1,659 verified projects, most $1,421–$5,138; materials for a typical 4-foot fence $25–$35, 3-foot $22–$26, 6-foot $33–$36 per linear foot; length table 50 ft $1,250–$1,750, 100 ft $2,500–$3,500, 150 ft $3,750–$5,250; plain black $25–$30, galvanized about $30, ornamental $30–$35, intricate designs up to about $50 per linear foot; contractors $30–$80 an hour, budget an additional 50% on top of material costs for labor, 200 ft about 30 hours / $900–$2,400; permits $20–$60; survey $200–$1,000; removal $3–$5 per linear foot; gates $600 small manual to over $8,500 automated driveway; brick columns $450–$1,275 each; DIY painting saves about $8–$10 per linear foot, recoating every 2–3 years; repair $253–$788, section replacement $50–$120 per linear foot; its general fence table lists wrought iron at $25–$55 per linear foot), HomeGuide's wrought iron fence cost guide ($50–$85 per linear foot installed for 4–6 ft heights; average project $10,000–$17,000; 100 ft $5,000–$8,500; 50 ft $2,500–$4,250; by height 3 ft $40–$50, 4 ft $50–$65, 5 ft $65–$75, 6 ft $75–$85; plain black $50–$60, galvanised $60–$65, ornamental $65–$85, custom $85–$130 per linear foot installed; labor $15–$25 per linear foot) and Fixr's wood fence cost page (wrought iron averages $22–$40 per linear foot installed; a 209-linear-foot project $4,598–$8,360) — Angi's length table is material-led while HomeGuide's band is full installed, published here as the scope split, not averaged away; the page's typical band follows HomeGuide's installed scope, and its $6,750 most-pay figure is the midpoint of HomeGuide's 100-foot band, not a guide-stated average. Sources last checked: October 2026 — HomeGuide, Fixr, Angi. How we calculate these costs

Cost by scope

Wrought Iron Fence Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Short plain run, about 50 feet$1,250 – $1,750The cheap end: Angi's length table puts 50 feet at $1,250–$1,750, and plain black iron — its cheapest style at $25–$30 per linear foot for materials — is what that end is built from
Standard 100-foot installed run, 4-foot — the typical job$5,000 – $8,500The shared band itself: HomeGuide's 100-foot installed band at $50–$85 per linear foot, with its 4-foot rate of $50–$65 inside it
Ornamental or custom large run, about 150 feet — the top end$9,750 – $19,500The expensive end: HomeGuide prices ornamental iron at $65–$85 per linear foot installed, or $9,750–$12,750 for 150 feet, and custom work at $85–$130, or $12,750–$19,500 for the same run

Where the money goes

Part of the jobShareNote
Iron panels and posts (plain, galvanized or ornamental)40–55% of totalThe iron: Angi prices materials at $25–$35 per linear foot for a typical 4-foot fence and ornamental at $30–$35, with intricate designs up to about $50 — style alone moves this line before labor is added
Installation labor (setting posts, hanging panels, leveling)35–50% of totalThe work: Angi prices contractors at $30–$80 an hour and tells readers to budget an additional 50% on top of material costs for labor, while HomeGuide prices labor at $15–$25 per linear foot — either way, a heavy metal fence is a two-person, post-by-post job
Gates, columns and hardware10–20% of totalThe extras: Angi prices a small manual gate from $600 and an automated driveway gate at over $8,500, with brick columns at $450–$1,275 each — a gated entry can cost more than a whole side run
Permits, survey and old-fence removal5–15% of totalThe paperwork and prep: Angi prices permits at $20–$60, a survey at $200–$1,000 and removal at $3–$5 per linear foot — small lines that still belong in the quote
Iron panels and posts (plain, galvanized or ornamental) · 40–55%Installation labor (setting posts, hanging panels, leveling) · 35–50%Gates, columns and hardware · 10–20%Permits, survey and old-fence removal · 5–15%
Estimator’s note: on a wrought iron fence installation, iron panels and posts (plain, galvanized or ornamental) is usually where quotes swing most (40–55% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
A house reached by a stone path between black metal gates: gates, posts and hardware are a separate line — 10–20% of a wrought iron total in this guide's breakdown
A house reached by a stone path between black metal gates: gates, posts and hardware are a separate line — 10–20% of a wrought iron total in this guide's breakdown

What moves the price most

Height is the first fork. HomeGuide prices installed wrought iron at $40–$50 per linear foot for 3 feet, $50–$65 for 4 feet, $65–$75 for 5 feet and $75–$85 for 6 feet — two extra feet of iron, posts and labor is a different price class, not a small uplift. Style is the second fork: plain black at $50–$60 installed, galvanized at $60–$65, ornamental at $65–$85 and custom at $85–$130 in HomeGuide, because scrollwork and custom forging are hand work priced by the foot. Gates and columns are the quiet budget-breakers: a single automated driveway gate can exceed the cost of a plain side run, and brick columns are priced per column. Finally, maintenance is a cycle, not a one-off: Angi notes recoating every 2–3 years, with DIY painting saving about $8–$10 per linear foot, and repair at $253–$788 with section replacement at $50–$120 per linear foot — rust left alone is what turns a recoat into a replacement.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A fence line along a path: whatever the style, the run is priced by the linear foot — and the plain-versus-ornamental gap is what moves the per-foot rate (this photo shows a picket fence line, not an iron sample)
A fence line along a path: whatever the style, the run is priced by the linear foot — and the plain-versus-ornamental gap is what moves the per-foot rate (this photo shows a picket fence line, not an iron sample)

Frequently asked questions

Why do Angi and HomeGuide prices for wrought iron differ so much?

Because they price different scopes: Angi's length table is material-led at $25–$35 per linear foot for a typical 4-foot fence, while HomeGuide's $50–$85 band is fully installed. A quote that looks like Angi's number usually excludes the labor HomeGuide includes — compare installed totals, not headline rates.

How much does a wrought iron gate add?

Angi prices a small manual gate from $600 and an automated driveway gate at over $8,500, with brick columns at $450–$1,275 each. Gates are priced per gate, not per foot, so a double driveway gate with automation is routinely the single most expensive line on an iron fence job.

Does wrought iron rust, and what maintenance does it need?

Yes, where its finish fails — which is why Angi notes recoating every 2–3 years. DIY painting saves about $8–$10 per linear foot, and the guides price repair at $253–$788 with section replacement at $50–$120 per linear foot. A recoat on schedule is cheap; a rusted section is not.

Is wrought iron more expensive than aluminum?

On installed rates, usually yes: HomeGuide prices wrought iron at $50–$85 per linear foot installed against aluminum at $25–$75, and its wrought iron average project of $10,000–$17,000 sits above aluminum's typical range. The gap buys weight, rigidity and custom ornamental work — not just a different metal.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Wrought Iron Fence Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Green powder-coated metal fence panel with a post

Aluminum Fence Installation Cost

$3,750 – $6,800

Aluminum fence installation typically costs $3,750 – $6,800 for about 150 linear feet of standard 4-foot picket fencing, with about $4,600 the figure most jobs land near — Angi, updated September 23, 2026, puts the national average at $4,607 with most homeowners paying $2,426–$6,791 and prices a complete project at $22–$72 per linear foot, while HomeGuide prices a 150-foot picket, pool or ornamental run at $3,750–$11,250 at $25–$75 per linear foot and EngineerFix prices a professionally installed black aluminum fence at $22–$72 per linear foot turnkey. The guides agree on the per-foot band; where they differ is scope — Angi's length table runs to 300 feet and HomeGuide's privacy tier runs to $130 per foot — so this page's typical band follows the standard picket overlap for 150 feet, with split-rail, ornamental and privacy tiers published separately.

Two-story gray house at dusk with a wide concrete driveway and three garage doors

Concrete Driveway Cost

$3,500 – $8,600

Typical 2-car driveway of about 576 sq ft in plain concrete, installed — about $6 – $15 per sq ft installed

Car parked in a snowy driveway beside a white house in winter

Heated Driveway Installation Cost

$7,500 – $15,000

A heated driveway installation typically costs $7,500 – $15,000 for a standard two-car driveway of about 600 sq ft, with about $13,000 the figure most standard jobs land near — Angi prices heated driveway installation at $12–$25 per sq ft with an average near $13,000, HomeGuide prices a heated concrete or asphalt driveway at $12–$28 per sq ft with a $14,600 national average and a $6,900–$22,400 average range, and HouseDigest puts the same work at $12–$28 per sq ft with a two-car driveway reaching about $16,000. The $7,500–$15,000 typical band is the $12–$25 per sq ft overlap applied to about 600 sq ft, and $13,000 is Angi's average — a mat-only job can come in far below it, and a hydronic system under pavers costs far more, while the heating system, surface, labor and controls below are all inside the total.

Single-story beige stucco house with a freshly painted exterior, neat lawn and concrete walkway

Exterior House Painting Cost

$3,000 – $7,500

Typical full exterior of an average home, washed, prepped and painted — about $1.50 – $4 per sq ft of paintable surface

Suburban house at sunset with a single and a double garage door

Garage Door Replacement Cost

$800 – $1,800

Typical replacement of one standard door, installed, with new tracks, springs and hardware

Two-story suburban house with a two-car garage, wide concrete driveway and manicured lawn

Garage Addition Cost

$25,000 – $45,000

A standard two-car garage (about 24 by 24 feet) built on the lot — slab, framing, roof, doors and basic electrical together, finished or unfinished as priced