Home › Cost Guides › Utility Sink Installation
Cost Guide

How Much Does a Utility Sink Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$300 – $800
Most homeowners pay around $500 · Replacing a standard utility sink where supply and drain connections already exist — sink, faucet and plumber’s installation included; a sink in a new spot with new lines priced separately
typical
$300$800
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Laundry room with a wall-mounted stainless steel utility sink, faucet and exposed drain

Utility Sink Installation cost at a glance

  • Typical range: $300 – $800
  • Most homeowners pay: around $500
  • Prices vary most by: Plumber labor (35–55% of the budget)

Cross-checked against two published sources for this project. Sources used for this page: Angi's sink installation cost guide, updated September 26, 2026 (utility sink installation $200–$500, not including new plumbing lines; national average sink installation $438, most $216–$663), HomeGuide's sink installation cost guide (utility sink replacement $330–$1,350 overall; new utility sink $100–$700; plumber install labor $200–$500; new utility sink installation $750–$3,000 where new lines are required) and EngineerFix's utility sink installation cost guide (freestanding plastic tub $50–$150; stainless steel or cast iron $150–$900; cabinet-integrated or double-basin units $1,000–$3,000 for the fixture alone; fittings $25–$75; labor $200–$600; new lines $450–$1,800; straightforward jobs one to four hours at existing hookups). Synthesized typical = the replacement-at-existing-hookups overlap at $300–$800, with $500 most-pay inside it. Checked November 2026.. Sources last checked: October 2026 — HomeGuide, Angi. How we calculate these costs

Cost by scope

Utility Sink Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Freestanding plastic tub, existing hookups$200 – $500The budget swap. Angi prices utility sink installation at $200–$500, and EngineerFix prices a freestanding plastic tub at $50–$150 for the basin alone.
Standard steel or cabinet sink$300 – $800The typical project on this page. HomeGuide prices a utility sink replacement at $330–$1,350 overall, with the sink at $100–$700 and plumber labor at $200–$500.
New sink in a new spot$750 – $3,000HomeGuide’s new-install band, where new supply and drain lines are the job. EngineerFix prices running new lines at $450–$1,800 on top of the sink itself.

Where the money goes

Part of the jobShareNote
Sink unit30–50% of totalThe basin itself. HomeGuide prices a new utility sink at $100–$700, and EngineerFix prices plastic tubs at $50–$150 against $150–$900 for stainless steel or cast iron.
Plumber labor35–55% of totalRemoving the old sink, setting the new one, and testing supply and drain. HomeGuide prices plumber install labor at $200–$500, and EngineerFix at $200–$600 for a straightforward job at existing hookups.
Faucet + drain fittings10–20% of totalTrap, drain assembly and supply lines at $25–$75 in EngineerFix’s pricing, plus the faucet itself.
Old sink removal + disposal5–15% of totalTaking the old basin away. HomeAdvisor prices removal at $20–$300 plus $20–$300 disposal, though a straightforward swap lands at the low end.
Sink unit · 30–50%Plumber labor · 35–55%Faucet + drain fittings · 10–20%Old sink removal + disposal · 5–15%
Estimator’s note: on a utility sink installation, plumber labor is usually where quotes swing most (35–55% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
A laundry sink set into a counter beside a washing machine — the sink unit is 30–50% of the job, from a $50–$150 plastic tub to $150–$900 for steel or cast iron in EngineerFix’s pricing.
A laundry sink set into a counter beside a washing machine — the sink unit is 30–50% of the job, from a $50–$150 plastic tub to $150–$900 for steel or cast iron in EngineerFix’s pricing.

What moves the price most

Existing hookups are the first decision: a replacement at connections that already exist is Angi’s $200–$500 band, while a sink in a new spot is HomeGuide’s $750–$3,000 new-install band, because EngineerFix prices the new lines alone at $450–$1,800. Material is second: a plastic tub at $50–$150 in EngineerFix’s pricing keeps the job at the budget end, while stainless steel or cast iron at $150–$900 moves it up and lasts longer under heavy use. Mounting is third: a freestanding tub is the simplest set, a cabinet sink adds the cabinet unit, and a high-end integrated or double-basin unit runs $1,000–$3,000 for the fixture alone in EngineerFix’s pricing. For the kitchen equivalent, see our kitchen sink installation guide, for the room around the sink, see our laundry room remodel guide, and for a leaking or damaged basin, see our sink repair guide.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Worked example: how a typical utility sink installation budget breaks down

A typical job: a standard stainless utility sink replacing a worn plastic tub in a laundry room, existing hot and cold supplies and drain reused, new faucet and trap fitted, old basin removed. The budget below totals $500 — the "most homeowners pay around" figure from the top of this page — split using this page's own cost breakdown. It shows how a real quote at that level is usually composed; every line is built from the ranges on this page, and it is an illustration, not a quote for your project.

Line itemExample budget
Stainless utility sink unit$180
Plumber labor (removal, setting, testing)$250
Faucet and drain kit$50
Removal and disposal of the old basin$20
Total$500

What most people get wrong

  • Pricing a new-spot sink at replacement rates — HomeGuide prices a new installation at $750–$3,000 because the lines are the job, not the basin.
  • Buying the sink before measuring the drain height — a basin whose outlet sits below the existing drain needs a pump or a re-route, neither of which is in a standard quote.
  • Comparing a tub-only price with an installed price — EngineerFix prices a plastic tub at $50–$150 for the basin alone, before the $200–$600 labor line.
  • Skipping the leak test — a slow trap leak under a laundry sink soaks a cabinet base for weeks before anyone notices.

Costs in your city

Utility sink pricing is plumber pricing: the same replacement costs near the bottom of the band where plumber rates are low and above it in high-rate metros, while the basin itself is a national retail item. Housing stock travels with the city — older homes with galvanized supply lines or cast-iron drains take longer to disconnect and adapt than a recent build with standard connections. Ask each bidder whether the faucet, the trap kit and disposal of the old basin are inside the number.

How this estimate was built: utility sink figures were cross-checked across Angi’s sink installation cost guide, HomeGuide’s sink installation cost guide and EngineerFix’s utility sink installation cost guide. Angi publishes utility installation at $200–$500, HomeGuide publishes replacement at $330–$1,350 with labor at $200–$500, and EngineerFix publishes labor at $200–$600 — so the typical band is drawn on the replacement-at-existing-hookups overlap, and new-spot work is tiered separately. Checked November 2026. Full method: How We Estimate Costs.
Hand-washing at a deep utility sink — the deep basin is the whole point of the fixture, and the reason a utility sink is priced apart from a bathroom or kitchen basin.
Hand-washing at a deep utility sink — the deep basin is the whole point of the fixture, and the reason a utility sink is priced apart from a bathroom or kitchen basin.

Frequently asked questions

How much does it cost to replace a utility sink?

A standard replacement at existing hookups typically runs $300–$800, with $500 the middle of that band; Angi prices utility installation at $200–$500 and HomeGuide prices replacement at $330–$1,350 overall.

How much does a utility sink cost in a new spot?

HomeGuide prices a new utility sink installation at $750–$3,000, because new supply and drain lines are a separate job — EngineerFix prices those lines at $450–$1,800 on top of the sink.

Plastic tub or steel sink — which is cheaper?

Plastic: EngineerFix prices a freestanding plastic tub at $50–$150, against $150–$900 for stainless steel or cast iron. Steel costs more and handles hot water, sharp tools and heavy loads better.

How long does a replacement take?

EngineerFix puts a straightforward installation at existing hookups at one to four hours of work — most of the visit is removal, setting and leak-testing, not the basin itself.

What pushes a utility sink above the typical band?

New water and drain lines, a cabinet or double-basin unit, and disposal of a heavy cast-iron basin. A quote should separate the sink, the labor and any new-line work so the three are comparable.

Before you sign: fix the basin and the hookup situation before you quote, confirm the faucet, trap kit and disposal are inside the number, get the new lines priced separately if the spot is new, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Utility Sink Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Marble-look tiled bathroom with a glass-enclosed walk-in shower beside a freestanding tub

Walk-In Shower Installation Cost

$6,000 – $10,000

The typical project is a standard walk-in shower built in an existing bathroom footprint — a tiled or quality prefab shower with a proper pan, waterproofing, a glass door or panel and mid-range fixtures, drain kept where it is. Curbless and custom work is priced in the top tier.

White kitchen with a double sink and a high-arc faucet under a window

Kitchen Faucet Installation Cost

$250 – $550

The typical project is a mid-range pull-down kitchen faucet installed by a plumber in the existing sink holes — old faucet removed, new supply lines fitted, sprayer connected and every joint checked dry. This page prices the faucet only; replacing the sink as well is priced separately in our kitchen sink guide.

Double vanity with matte black centerset faucets and a marble-look tiled shower behind

Bathroom Faucet Installation Cost

$230 – $600

The typical project is a standard centerset or widespread bathroom faucet replaced by a plumber in the existing sink holes — old faucet removed, new supply lines fitted, drain pop-up connected and every joint checked dry. This page prices the bathroom sink faucet only; a tub faucet or a new sink is priced separately.

Large white jetted bathtub in a tiled bathroom with a vanity

Bathtub Refinishing Cost

$350 – $630

The typical project is a full professional refinish of a standard built-in tub — stripped, repaired, bonded and sprayed in place, ready to use in a day or two. A liner, an inlay and a full replacement are different projects: the replacement is priced on the bathtub replacement page, and liners are tiered as an alternative below, never blended into this band.

Black and white checkered tile floor with visible grout lines and ground-in grime

Tile and Grout Cleaning Cost

$285 – $675

The typical project is a professional machine clean of the main tiled areas of a home — kitchen, bathrooms and entry — at about $0.50 – $3 per sq ft in Angi. A single small bathroom, grout sealing and damaged tile are tiered or noted separately below; new tile is priced on the tile flooring page.

Kitchen cabinets finished in deep blue paint with patterned tile backsplash

Cabinet Painting Cost

$1,000 – $6,500

Professional cabinet painting, average kitchen — about $30–$70 per linear foot across the published guides