Home › Cost Guides › Pot Filler Installation
Cost Guide

How Much Does a Pot Filler Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$975 – $2,000
Most homeowners pay around $1,400 · Installing a pot filler faucet — a folding cold-water tap over the stove, with a new water line run through the wall and the wall and backsplash patched — typically costs $975–$2,000, with most homeowners paying around $1,400.
typical
$975$2,000
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
A bright white kitchen with cabinets and a stove under a range hood

Pot Filler Installation cost at a glance

  • Typical range: $975 – $2,000
  • Most homeowners pay: around $1,400

Cross-checked against one published sources for this project. Sources used for this page: Angi, How Much Does It Cost to Install A Pot Filler Faucet? [2026 Data] (updated Oct 29, 2026 — national average $1,650; most pay $975-$3,000; scope $280 faucet-only to $3,000+ major plumbing + structural; labor $45-$200/hr; Angi's second article frames $1,650 as installation with existing plumbing, up to $3,000 for new water line work; faucet $150-$200 in one passage vs $150-$600 elsewhere — page uses the cross-checked $150-$600); ABS Pipes, Adding a Pot Filler: Installation Cost & Plumbing (2026) (published Oct 18, 2026, updated Nov 4, 2026 — total $500-$2,500; faucet $150-$600; labor $300-$1,800; new build $500-$1,300 vs retrofit $1,150-$2,500 through finished walls; tile add $200-$600; mount 12-18 in above cooktop; cold water only); Cost to Renovate, Pot Filler Installation Cost in 2026 (no date shown on the page — national $700-$2,000, avg $1,200; tiers $450 / $1,050 / $2,275; faucet by finish $150-$1,500; water line $100-$1,000; wall/backsplash $0-$500; shutoff $50-$200; 4-8 hrs typical; permits $0-$75 in tiers). Disagreements flagged, not averaged away: average Angi $1,650 vs Cost to Renovate $1,200 — most-pay $1,400 sits between the two published averages; top end Angi $3,000 vs ABS Pipes $2,500 typical cap vs Cost to Renovate $2,000 typical / $3,500 premium ceiling; mounting height ABS Pipes 12-18 in vs another guide 20-24 in — no single height published as fact. EngineerFix was read but NOT counted as independent (its $975-$3,000 / $1,650 figures mirror Angi verbatim). The 'adds ~3.2% to home value' claim was NOT verified by any primary source — not used. Worked example and shares are derived from the source ranges, not published percentages. Checked November 2026.. Sources last checked: October 2026 — Angi. How we calculate these costs

Cost by scope

Pot Filler Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Budget — basic chrome faucet, line already accessible$400 – $600A basic chrome pot filler ($150–$300) with a cold-water-only connection where the water line is already accessible behind the wall, minimal wall work, no permit. Cost to Renovate prices this tier at $450: materials $200 + labor $250 + permits $0.
Mid-range — brushed nickel or stainless, new water line$850 – $1,600The typical project on this page: a brushed-nickel or stainless faucet ($300–$600), a new cold-water line run from the nearest supply, and drywall patching included. Cost to Renovate prices this tier at $1,050: materials $450 + labor $550 + permits $50; ABS Pipes prices the adjacent-wall remodel scenario at $650–$1,600.
Premium — designer faucet, hot + cold lines, tile repair$2,000 – $3,000+A designer faucet such as Brizo, Waterstone or Rohl ($800–$1,500), hot- and cold-water lines, and tile backsplash repair in a premium finish. Cost to Renovate prices this tier at $2,275: materials $1,200 + labor $1,000 + permits $75; Angi runs to $3,000 and beyond with major plumbing and structural work.

Where the money goes

Part of the jobShareNote
Pot filler faucet — mid-range brushed nickel or stainless32% of total$450 — inside ABS Pipes' $150–$600 faucet band and Cost to Renovate's $300–$600 mid-range band. Share derived from the worked example below, not a published percentage.
Plumbing labor — new cold-water line rough-in43% of total$600 — inside ABS Pipes' $300–$1,800 labor band and close to Cost to Renovate's $550 mid-range labor figure. Share derived from the worked example below, not a published percentage.
Wall repair + tile and backsplash patching14% of total$200 — inside ABS Pipes' $200–$600 tile add and Cost to Renovate's $0–$500 wall and backsplash band. Share derived from the worked example below, not a published percentage.
Shutoff valve, fittings, wall blocking7% of total$100 — inside Cost to Renovate's $50–$200 shutoff band; Angi's small-materials list totals $165. Share derived from the worked example below, not a published percentage.
Permit4% of total$50 — Cost to Renovate's mid-range permit figure; real permit cost is jurisdiction-dependent and sometimes $0. Share derived from the worked example below, not a published percentage.
Pot filler faucet — mid-range brushed nickel or stainless · 32%Plumbing labor — new cold-water line rough-in · 43%Wall repair + tile and backsplash patching · 14%Shutoff valve, fittings, wall blocking · 7%Permit · 4%
Estimator’s note: on a pot filler installation, plumbing labor — new cold-water line rough-in is usually where quotes swing most (43% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
A cooktop set under its range hood — in a retrofit, the new water line is run through the finished wall behind this stove wall
A cooktop set under its range hood — in a retrofit, the new water line is run through the finished wall behind this stove wall

What moves the price most

Retrofit versus new build is the single biggest driver. With walls open during a remodel or new build, a pot filler typically runs $500–$1,300 (ABS Pipes); retrofitting the same faucet into a finished kitchen runs $850–$2,500, because the plumber must open finished walls, run the line, and repair drywall and tile. Installing during a remodel saves $200–$500 in access costs (Cost to Renovate) — if a remodel is planned, have the plumber stub the line and blocking in during rough-in even before buying the faucet. Faucet finish and brand: basic chrome $150–$300, brushed nickel or stainless $300–$600, matte black $350–$700, and brass, gold or designer brands such as Waterstone, Brizo or Rohl $800–$1,500 (Cost to Renovate). Wall material: drywall is cheap to open and patch; cutting a tile backsplash adds $200–$500, and a stone-slab backsplash costs more still (Cost to Renovate), while plaster, brick or stone veneer also slow the work (ABS Pipes). Distance from the water line: $100–$300 if a line is accessible behind the stove wall, $500–$1,000 if the nearest supply is across the kitchen or must run through finished walls (Cost to Renovate). Permits and labor rates: permits run $0–$75 in Cost to Renovate's tiers, though one single-city estimate (Nashville) lists $80–$160 — permit cost varies by jurisdiction and should not be read as a firm national figure. Plumber labor runs $45–$200 per hour (Angi), and high-cost metros run 25–40% above national figures (ABS Pipes). Where the sources disagree: the national average is $1,650 (Angi) against $1,200 (Cost to Renovate) — Angi's own second article frames $1,650 as installation with existing plumbing, with up to $3,000 for new water-line work, so its average may already assume a line exists. This page's $1,400 most-pay figure sits between the two published averages. Mounting height is also genuinely disputed: ABS Pipes says 12–18 inches above the cooktop, while another guide recommends 20–24 inches — always follow the faucet maker's and your range's clearance requirements. Worked example at the most-pay figure: a mid-range retrofit with a new cold-water line — faucet $450 + plumbing labor $600 + wall repair and tile patching $200 + shutoff valve, fittings and wall blocking $100 + permit $50 = $1,400. The shares are whole-percent roundings of this worked example. For the range the faucet serves see our range installation guide, for the cooktop beside it see our cooktop installation guide, for the faucet it should match see our kitchen faucet installation guide, for the sink and counter it sits over see our kitchen sink installation guide, and for the backsplash it cuts through see our backsplash installation guide.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A chrome kitchen faucet over a marble counter — match the pot filler's finish to the kitchen's main faucet and hardware
A chrome kitchen faucet over a marble counter — match the pot filler's finish to the kitchen's main faucet and hardware

Frequently asked questions

How much does it cost to install a pot filler?

Most homeowners pay $975–$2,000, with $1,400 a typical mid-range total. Angi puts the national average at $1,650; Cost to Renovate at $1,200. The spread is driven almost entirely by how far the nearest cold-water line is from the stove wall.

Is it cheaper to add a pot filler during a remodel or new build?

Yes — by a wide margin. With walls open it typically runs $500–$1,300 (ABS Pipes); retrofitting the same faucet into a finished kitchen runs $850–$2,500 because the plumber must open finished walls, run the line, and repair drywall and tile. If a remodel is planned, have the plumber stub the line and blocking in during rough-in even before buying the faucet.

Does a pot filler need hot water?

No — pot fillers supply cold water only, since the water goes straight onto the stove to be heated (Angi, ABS Pipes). Running a hot line as well is a premium option, not the standard.

How high above the stove should a pot filler be mounted?

Sources disagree: ABS Pipes says 12–18 inches above the cooktop, while another guide recommends 20–24 inches. Either way it must clear your tallest stockpot while staying reachable — follow the faucet manufacturer's and your range's clearance requirements.

Can a pot filler be added to an existing kitchen?

Yes — retrofitting is common, but it costs more than adding one during a remodel, because the plumber must run a new water line through finished walls or cabinets and repair the openings afterward (ABS Pipes). Expect a straightforward retrofit to take 4–8 hours, and up to 2 days if the line must cross the kitchen.

Do pot fillers leak, and do I need a shutoff valve?

A quality faucet with ceramic disc cartridges rarely leaks, but the articulated joints are the most likely drip point (ABS Pipes). A dedicated shutoff valve in an accessible spot — such as inside an adjacent cabinet, not buried behind the stove — is strongly recommended so any leak can be stopped quickly; adding one costs $50–$200 (Cost to Renovate). Any leak drips onto the range and into the wall cavity, so the connection must be pressure-tested.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Pot Filler Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

A backlit bathroom mirror reflecting a chrome ladder-style towel rail

Heated Towel Rack Installation Cost

$500 – $1,200

Installing a heated towel rack — a hardwired electric towel warmer mounted on the bathroom wall, with a dedicated circuit and the wall patched and painted — typically costs $500–$1,200, with most homeowners paying around $800.

A curved glass shower enclosure with a rain showerhead beside a backlit bathroom mirror

Shower Niche Installation Cost

$250 – $650

Adding a recessed shower niche — a waterproofed, tiled shelf cut into the shower wall — typically costs $250–$650, with most homeowners paying around $450.

A backlit bathroom mirror over a white vanity beside a wooden door

Bathroom Mirror Installation Cost

$150 – $400

Installing a bathroom mirror — a framed or frameless vanity mirror, mounted level with proper backing, with old-mirror removal — typically costs $150–$400, with most homeowners paying around $300.

A large white oval drop-in bathtub in a tiled bathroom

Jetted Tub Installation Cost

$2,500 – $7,500

Installing a jetted (whirlpool) tub — a mid-range 60-inch acrylic water-jet tub replacing an existing tub in the same footprint, with a new dedicated GFCI circuit — typically costs $2,500–$7,500, with most mid-range jobs landing around $5,500.

A green clawfoot bathtub with white ornate feet and a freestanding chrome faucet on a wooden floor

Clawfoot Tub Installation Cost

$2,000 – $5,500

$3,500 is CostToRenovate's published national average — compiled from Fixr 2025 data, NOT a derived midpoint — and the page labels that provenance. The full freestanding/clawfoot band is $1,200–$10,000 (Fixr); large ornate new clawfoot tubs run $10,000+ (Angi). A budget acrylic job is about $1,300; a mid-range cast iron job about $3,100; a premium restored-antique job about $6,850 (CostToRenovate tiers).

Modern finished bathroom with a glass shower enclosure and wall-hung sink

Bathroom Remodel Cost

$6,500 – $18,000

A standard full bathroom remodel — a new tub or shower, vanity, toilet and tile in a typical 40–50 sq ft bath with the layout unchanged — typically costs $6,500–$18,000, with most homeowners paying around $12,000.