Home › Cost Guides › Metal Roofing Installation
Cost Guide

How Much Does a Metal Roofing Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$13,000 – $28,000
Most homeowners pay around $19,000 · Metal roofing installation typically costs $13,000 – $28,000, with about $19,000 the most-pay figure — Angi prices a steel roof at $19,000 on average with a $16,000–$28,000 range, HomeGuide prices a metal roof at $5–$16 per square foot installed for $7,500–$40,000 on average, and Modernize prices steel at $4–$21 per square foot with a 2,000-square-foot roof at $8,000–$42,000 and many jobs near $16,000. The $19,000 most-pay figure is Angi's steel-roof average; a corrugated roof on a modest house lands below it and copper or stainless on a large roof lands far above it, at $11 per square foot on Angi's average against HomeGuide's $5–$16 band.
typical
$13,000$28,000
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Two roofers fitting a metal panel on a brick house

Metal Roofing Installation cost at a glance

  • Typical range: $13,000 – $28,000
  • Most homeowners pay: around $19,000
  • Prices vary most by: Installation labor (40–55% of the budget)

Cross-checked against three published sources for this project. Sources used for this page: Angi's steel roof cost guide (2026, updated July 20, 2026: average $19,000, range $16,000-$28,000, $11 per square foot average with a $6-$16 normal range; size table 1,200 sq ft $13,200 / $7,200-$19,200, 1,500 $16,500 / $9,000-$24,000, 2,000 $22,000 / $12,000-$32,000, 2,500 $27,500 / $15,000-$40,000, 3,000 $33,000 / $18,000-$48,000; labor 40-60% of total, $7,600-$11,400 on an average roof; corrugated $6-$10, metal shingles $10-$14, sheet metal $7-$11, standing seam $12-$16 per square foot; galvanized $10-$16, stamped $7-$12, stainless $10-$16, painted $7-$13; demolition and disposal $1,000-$5,000; permits $250-$500; decking replacement $2-$5 per square foot; steel roof repair average $1,500, $1,000-$5,000, 50% repair-versus-replace rule; return on investment 55-80%; lifespan average 50 years, steel 30-60, aluminum 20-45, tin to 75, zinc, stainless and copper 80-100+ years), HomeGuide's roof replacement cost guide (2026: metal roof $5-$16 per square foot installed, $7,500-$40,000 on average; corrugated $5-$12, $6,000-$22,000; standing seam $9-$16, $13,500-$40,000; metal shingle $6-$14, $9,000-$35,000; stone-coated steel $7-$13, $12,200-$25,900; stainless $10-$21, $15,000-$52,500; copper $13-$30, $19,500-$75,000; tin $6-$18; zinc $10-$20) and Modernize's steel roof cost guide (2026: steel $4-$21 per square foot; 2,000 sq ft $8,000-$42,000, many homeowners around $16,000; corrugated $4-$14; standing seam $8-$16; steel shingles $7-$15; stone-coated $10-$18). Sources last checked: October 2026 — HomeGuide, Modernize, Angi. How we calculate these costs

Cost by scope

Metal Roofing Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Corrugated or exposed-fastener steel — the budget metal roof$8,000 – $18,000The cheap end: HomeGuide prices a corrugated or sheet-metal roof at $5–$12 per square foot installed ($6,000–$22,000 in total) and Angi prices corrugated steel at $6–$10 per square foot — the lowest material and labor bill, but exposed fasteners need periodic inspection and resealing where standing seam needs none
Standard standing-seam or metal shingle — the typical residential job$13,000 – $28,000The shared band itself: Angi's $16,000–$28,000 steel range with its $19,000 average, inside HomeGuide's $9–$16 per square foot standing-seam band ($13,500–$40,000) and Modernize's $8–$16 standing-seam band — concealed fasteners, clean lines and the profile most residential quotes describe
Premium copper, stainless or stone-coated steel — the top of the market$25,000 – $50,000The expensive end: HomeGuide prices copper at $13–$30 per square foot installed ($19,500–$75,000 in total), stainless at $10–$21 ($15,000–$52,500) and stone-coated steel at $7–$13 ($12,200–$25,900) — copper totals past $50,000 on large or complex roofs are published in the sources, not blended into this tier

Where the money goes

Part of the jobShareNote
Panels and roofing materials35–50% of totalAngi prices steel at $6–$16 per square foot installed with galvanized at $10–$16, painted at $7–$13 and stainless at $10–$16, against HomeGuide's metal band of $5–$16 — gauge, coating and profile move this line most, and copper at $13–$30 per square foot on HomeGuide is a different budget altogether
Installation labor40–55% of totalAngi prices labor at 40–60% of a steel roof total, or $7,600–$11,400 on an average roof — pitch, height, complexity and any decking repair found at tear-off push labor up fastest, which is why two quotes for the same panels can differ by thousands
Tear-off, disposal and underlayment5–15% of totalAngi prices demolition and disposal at $1,000–$5,000 including the old roof and underlayment, and decking replacement at $2–$5 per square foot where rot or damage is found underneath — a roof laid over old shingles skips part of this line and inherits its problems
Permits, flashing, trim and finishing5–10% of totalAngi prices roofing permits at $250–$500 and notes a permit is needed in almost all cases, with flashing, ridge caps, snow guards and trim closing the bill — small in dollars, but the line whose absence voids warranties and fails inspections
Panels and roofing materials · 35–50%Installation labor · 40–55%Tear-off, disposal and underlayment · 5–15%Permits, flashing, trim and finishing · 5–10%
Estimator’s note: on a metal roofing installation, installation labor is usually where quotes swing most (40–55% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
Two roofers working on a corrugated metal roof like this one are the budget profile on this page: Angi prices corrugated steel at $6–$10 per square foot against $12–$16 for standing seam, and HomeGuide prices corrugated at $5–$12 — the exposed fasteners you can see here are why corrugated costs less to install and more to maintain
Two roofers working on a corrugated metal roof like this one are the budget profile on this page: Angi prices corrugated steel at $6–$10 per square foot against $12–$16 for standing seam, and HomeGuide prices corrugated at $5–$12 — the exposed fasteners you can see here are why corrugated costs less to install and more to maintain

What moves the price most

Size is the first driver: Angi prices steel at $11 per square foot on average, with its size table running $13,200 for 1,200 square feet, $22,000 for 2,000 and $33,000 for 3,000 — every extra roof plane is another run of panels and labor. Profile is second: Angi prices corrugated at $6–$10 per square foot against standing seam at $12–$16 and metal shingles at $10–$14, and HomeGuide prices standing seam at $9–$16 against corrugated at $5–$12 — the concealed-fastener system costs more to install and less to maintain. Metal is third: galvanized and painted steel are the value choice on Angi's figures, stainless and copper the premium one, and coastal salt air pushes buyers toward aluminum or stainless because plain steel rusts faster there. Tear-off and deck condition are fourth: Angi prices demolition and disposal at $1,000–$5,000 and decking replacement at $2–$5 per square foot, so a roof hiding rot costs more than its panel price suggests. Pitch, complexity and location close the bill: Angi's location table runs $11,500–$23,000 in Buffalo against $18,000–$36,000 in San Francisco for the same steel roof, and steep or cut-up roofs price above simple gables everywhere.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A roofer fitting ridge flashing and trim on a corrugated roof like this one is the finishing line: Angi prices permits at $250–$500 and flashing, ridge caps and trim close the bill — small in dollars, but the line whose absence fails inspections and voids warranties
A roofer fitting ridge flashing and trim on a corrugated roof like this one is the finishing line: Angi prices permits at $250–$500 and flashing, ridge caps and trim close the bill — small in dollars, but the line whose absence fails inspections and voids warranties

Frequently asked questions

How much does metal roofing installation cost?

Typically $13,000–$28,000, with about $19,000 the most-pay figure. Angi prices a steel roof at $19,000 on average with a $16,000–$28,000 range, HomeGuide prices metal at $5–$16 per square foot installed for $7,500–$40,000 on average, and Modernize prices steel at $4–$21 per square foot — the three sources agree on this page's band for a standard steel roof.

What does a metal roof cost per square foot?

Angi prices steel at $6–$16 per square foot installed with an $11 average, HomeGuide prices metal overall at $5–$16, and Modernize prices steel at $4–$21 — the bands differ because Angi's is steel-specific, HomeGuide's covers all metals and Modernize's spans corrugated to stone-coated. For a single-material quote, use the profile band: corrugated $5–$12 (HomeGuide), standing seam $9–$16 (HomeGuide) or $12–$16 (Angi).

Is corrugated or standing seam cheaper?

Corrugated, by a clear margin: Angi prices corrugated steel at $6–$10 per square foot against standing seam at $12–$16, and HomeGuide prices corrugated at $5–$12 against standing seam at $9–$16. Standing seam costs more because its fasteners are concealed and its panels are site-formed, but it needs less fastener maintenance over its life.

How long does a metal roof last, and does it rust?

Angi puts a metal roof's average life at 50 years, with steel at 30–60 years, aluminum at 20–45, tin up to 75 and zinc, stainless and copper at 80–100 years or more. Steel can rust, but painted or galvanized (zinc-coated) steel resists it well except in salty coastal air, where aluminum or stainless is the safer metal.

Do I need a permit, and what does tear-off add?

In almost all cases, yes: Angi prices roofing permits at $250–$500 and warns that building without one can mean penalties or removing the roof. Tear-off and disposal add $1,000–$5,000 on Angi's figures, plus $2–$5 per square foot for any decking that must be replaced once the old roof is off.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Metal Roofing Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

A finished basement living space with a carpeted floor and a stair

Egress Window Installation Cost

$2,700 – $5,900

Egress window installation typically costs $2,700 – $5,900 per window, with about $4,200 the most-pay figure — Angi's 2026 data from 760 verified projects puts the national average at $4,236 with most homeowners spending $2,723–$5,881, Modernize prices the job at $2,600–$5,800 with a $4,000 average, and Fixr prices a prefabricated below-ground installation at $2,500–$5,000 with a $3,500 average. The $4,200 most-pay figure is Angi's $4,236 average rounded; an above-grade window with no excavation lands far below it and an oversized or custom below-ground window lands above it.

Gravel-filled drainage trench running across a construction site

Window Well Installation Cost

$1,800 – $3,000

Window well installation typically costs $1,800 – $3,000 for a standard well with drainage, with about $2,200 the figure most jobs land near — Angi's national average is $2,200 inside its $1,800–$3,000 most-pay band, and HomeGuide's full range of $1,000–$5,000 brackets it on both sides. This guide covers the well alone — the corrugated, steel, fiberglass or concrete surround plus its drainage — at an existing basement window; cutting a new window or enlarging one is a bigger job, covered in our egress window guide.

Stone steps up to a wooden front door

Wheelchair Ramp Installation Cost

$1,100 – $3,600

Wheelchair ramp installation typically costs $1,100 – $3,600, with about $2,300 the figure most standard jobs land near — Angi averages $2,294 across 860 verified projects with most jobs at $1,123–$3,588, HomeAdvisor publishes the same $2,294 average and $400–$6,000 range (it is not an independent second average, so this page counts it once), Mr. Handyman prices a standard residential ramp at $1,000–$10,000, and Fixr prices a ramp added to a porch job at $1,400–$3,000. The $1,100–$3,600 typical band is Angi's most-common band rounded, and $2,300 is its $2,294 average rounded.

Couple with a wheelbarrow of straw mulch in a yard, with mulch and soil piles behind them

Landscaping Installation Cost

$1,250 – $6,100

Landscaping installation typically costs $1,250 – $6,100, with about $3,500 the figure most standard-lot jobs land near — Angi prices the national average at $3,517 with most homeowners paying $1,248–$6,068, HomeGuide prices the planted pieces of the same job (shrubs $25–$85 each, trees $200–$700, a new raised bed $1,200–$4,000, sod $1–$2 per square foot), and LawnGuru prices planting and bed installs at $1,000–$6,000. The $1,250–$6,100 typical band is a standard lot without major hardscape, and $3,500 is Angi's $3,517 average rounded; a small planting refresh costs less, and a full backyard renovation with hardscape costs far more.

Covered front porch with columns and seating on a grey house

Patio Cover Installation Cost

$4,500 – $12,000

Patio cover installation typically costs $4,500 – $12,000, with about $8,500 the figure most standard jobs land near — Angi prices the national average at $8,500 with most homeowners paying $4,500–$12,000 at $20–$50 per square foot, HomeGuide prices a patio cover alone at $20–$60 per square foot with aluminum at $4,000–$10,000 and wood at $12,000–$24,000, and GlobusGates prices most covers at $20–$70 per square foot. The $4,500–$12,000 typical band is an attached solid cover over an existing patio of roughly 200–240 square feet, and $8,500 is Angi's average; a basic aluminum cover costs less, and a wood, custom or louvered cover costs more.

House with red-and-white striped fabric awnings over two upper windows

Awning Installation Cost

$1,450 – $4,650

Awning installation typically costs $1,450 – $4,650, with about $3,000 the figure most standard jobs land near — Angi prices the national average at $3,040 with most homeowners paying $1,454–$4,652, HomeGuide prices manual retractable awnings at $200–$3,000 and motorized at $1,000–$6,000, and Habitatista prices retractable awnings at $2,000–$3,500 installed. The $1,450–$4,650 typical band is the standard patio or deck awning, and $3,000 is Angi's $3,040 average rounded; a small fixed window awning costs far less, and a large motorized or custom awning costs far more.