Home › Cost Guides › Farmhouse Sink Installation
Cost Guide

How Much Does a Farmhouse Sink Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$1,000 – $4,000
Most homeowners pay around $2,200 · Installing a farmhouse/apron-front kitchen sink with cabinet modification — sink, cabinet support work and plumbing reconnection included; a countertop re-cut or a full countertop replacement priced separately
typical
$1,000$4,000
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Stainless steel farmhouse sink with an exposed apron front under a kitchen window

Farmhouse Sink Installation cost at a glance

  • Typical range: $1,000 – $4,000
  • Most homeowners pay: around $2,200
  • Prices vary most by: Sink unit (40–60% of the budget)

Cross-checked against two published sources for this project. Sources used for this page: Angi's sink installation cost guide, updated September 26, 2026 (farmhouse sinks $1,000–$4,000; national sink installation average $438, most $216–$663; old sink removal $20–$300), HomeGuide's farmhouse sink cost guide (total $500–$5,000; sink $200–$3,500; installation labor $300–$1,500; standard plumbing labor $230–$650; top-mount installation $300–$800; undermount $400–$1,500; fireclay sinks $600–$1,400; stainless steel $200–$1,500; removal $30–$150; plumber $75–$150 per hour) and EngineerFix's farmhouse sink cost guide (sink $200–$2,000+; fireclay $500–$2,500+; stainless steel from $220, premium over $2,000; cast iron and copper $650–$2,000+; labor $300–$1,500; removal $30–$150; cabinet support frame or cradle $150–$400; plumbing reconfiguration $200–$600; fireclay and cast-iron units over 100 lb). Synthesized typical = Angi's farmhouse band at $1,000–$4,000, corroborated by HomeGuide's total, with $2,200 most-pay inside it. Checked November 2026.. Sources last checked: October 2026 — HomeGuide, Angi. How we calculate these costs

Cost by scope

Farmhouse Sink Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Stainless steel farmhouse, light cabinet work$800 – $1,800EngineerFix prices a stainless basin from about $220, and HomeGuide prices a top-mount sink installation at $300–$800 — the lightest cabinet-work end of the farmhouse job.
Standard fireclay farmhouse, cabinet modification$1,000 – $4,000The typical project on this page. Angi prices farmhouse sinks at $1,000–$4,000; HomeGuide prices fireclay sinks at $600–$1,400 and farmhouse installation labor at $300–$1,500.
Premium cast iron, copper or countertop re-cut$3,000 – $5,000+HomeGuide totals run to $5,000; EngineerFix prices cast iron and copper basins from $650 to over $2,000, plus cabinet work and any countertop re-cut.

Where the money goes

Part of the jobShareNote
Sink unit40–60% of totalHomeGuide prices farmhouse sinks at $200–$3,500 by material, with fireclay at $600–$1,400.
Cabinet modification and support15–25% of totalCutting the cabinet front and building the support frame; EngineerFix prices a support frame or cradle at $150–$400.
Plumbing labor and reconnection15–25% of totalReconnecting supply and drain to the deeper, forward basin; EngineerFix prices plumbing reconfiguration at $200–$600.
Faucet parts, removal and disposal5–15% of totalHomeGuide and EngineerFix both price old-sink removal at $30–$150, with faucet parts on top.
Sink unit · 40–60%Cabinet modification and support · 15–25%Plumbing labor and reconnection · 15–25%Faucet parts, removal and disposal · 5–15%
Estimator’s note: on a farmhouse sink installation, sink unit is usually where quotes swing most (40–60% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
A white double-bowl farmhouse sink set into wooden countertops — fireclay sinks run $600–$1,400 in HomeGuide's pricing, and the basin alone is 40–60% of the job.
A white double-bowl farmhouse sink set into wooden countertops — fireclay sinks run $600–$1,400 in HomeGuide's pricing, and the basin alone is 40–60% of the job.

What moves the price most

Material and weight are the first choice: stainless from about $220 in EngineerFix's pricing is the light end, fireclay at $600–$1,400 in HomeGuide's pricing is the standard job, and cast iron or copper from $650 to over $2,000 is the premium tier. Cabinet modification is second: the apron front forces the cabinet front to be cut and a support frame built — the 15–25% line that separates a farmhouse install from a standard sink swap. Plumbing depth is third: the deeper, forward basin often needs the drain re-routed, at $200–$600 in EngineerFix's pricing. For a standard sink swap with no apron front, see our kitchen sink installation guide, for the countertop work around it, see our countertop installation guide, and for the wider kitchen project, see our kitchen remodel guide.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Worked example: how a typical farmhouse sink installation budget breaks down

A typical job: a standard 30-inch fireclay farmhouse sink replacing a drop-in sink, cabinet front modified, support frame built, plumbing rerouted to the deeper basin, old sink removed. The budget below totals $2,200 — the "most homeowners pay around" figure from the top of this page — split using this page's own cost breakdown. It shows how a real quote at that level is usually composed; every line is built from the ranges on this page, and it is an illustration, not a quote for your project.

Line itemExample budget
Sink unit (fireclay farmhouse sink)$1,100
Cabinet modification and support frame$500
Plumbing labor and reconnection$400
Removal, disposal and parts$200
Total$2,200

What most people get wrong

  • Ordering the sink before measuring the cabinet — the cabinet front has to be cut to the basin, and a basin wider than the cabinet is a reorder, not a trim.
  • Assuming a countertop re-cut is included — the re-cut sits in the premium tier, and discovering it at install day is the expensive surprise.
  • Under-supporting a heavy basin — fireclay and cast-iron units run over 100 lb, and EngineerFix prices the support frame at $150–$400 for a reason.
  • Comparing a labor-only price with a sink-included price — Angi's farmhouse band is $1,000–$4,000 with the basin, while a plumber's labor line alone is a fraction of that.

Costs in your city

Farmhouse sink pricing is plumber-plus-carpenter pricing: the same standard job costs near the bottom of the band where trade rates are low and above it in high-rate metros, while the basin itself is a national retail item. Housing stock travels with the city — older face-frame cabinets take more modification than frameless boxes, and older plumbing takes longer to reroute. Ask each bidder whether the support frame, plumbing reconfiguration and disposal of the old sink are inside the number.

How this estimate was built: farmhouse sink figures were cross-checked across Angi's sink installation cost guide, HomeGuide's farmhouse sink cost guide and EngineerFix's farmhouse sink cost guide. Angi publishes farmhouse sinks at $1,000–$4,000, HomeGuide publishes totals at $500–$5,000 with fireclay at $600–$1,400, and EngineerFix publishes labor at $300–$1,500 with support frames at $150–$400 — so the typical band is drawn on Angi's farmhouse band, and stainless and premium tiers are kept separate. Checked November 2026. Full method: How We Estimate Costs.
A white apron-front sink in a sunlit kitchen — the apron front is what forces the cabinet modification, the 15–25% line that separates a farmhouse install from a standard sink swap.
A white apron-front sink in a sunlit kitchen — the apron front is what forces the cabinet modification, the 15–25% line that separates a farmhouse install from a standard sink swap.

Frequently asked questions

How much does a farmhouse sink installation cost?

Typically $1,000–$4,000, with $2,200 the middle of that band; Angi prices farmhouse sinks at $1,000–$4,000, and HomeGuide totals run $500–$5,000.

Why does a farmhouse sink cost more than a standard sink?

The cabinet front has to be cut and a support frame built for a basin that can weigh over 100 lb in fireclay or cast iron, and the deeper basin often needs plumbing re-routed — EngineerFix prices the support frame at $150–$400 and plumbing reconfiguration at $200–$600.

Stainless steel or fireclay?

EngineerFix prices a stainless basin from about $220, while HomeGuide prices fireclay sinks at $600–$1,400 — fireclay is heavier, needs the support frame, and is the standard job on this page.

Does the price include cutting the countertop?

No — a countertop re-cut is in the premium tier, not the typical band, so confirm in writing whether your countertop needs cutting and who pays for it.

Can a farmhouse sink fit my existing cabinets?

Only with cabinet modification — the cabinet front rail has to be cut and a support frame built, which is why cabinet work is its own 15–25% line; ask the installer to confirm your cabinet type before you order the sink.

Before you sign: measure the cabinet before you order, confirm the support frame and plumbing reconfiguration are inside the number, confirm whether a countertop re-cut is needed and who pays for it, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Farmhouse Sink Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Laundry room with a wall-mounted stainless steel utility sink, faucet and exposed drain

Utility Sink Installation Cost

$300 – $800

Replacing a standard utility sink where supply and drain connections already exist — sink, faucet and plumber’s installation included; a sink in a new spot with new lines priced separately

Marble-look tiled bathroom with a glass-enclosed walk-in shower beside a freestanding tub

Walk-In Shower Installation Cost

$6,000 – $10,000

The typical project is a standard walk-in shower built in an existing bathroom footprint — a tiled or quality prefab shower with a proper pan, waterproofing, a glass door or panel and mid-range fixtures, drain kept where it is. Curbless and custom work is priced in the top tier.

White kitchen with a double sink and a high-arc faucet under a window

Kitchen Faucet Installation Cost

$250 – $550

The typical project is a mid-range pull-down kitchen faucet installed by a plumber in the existing sink holes — old faucet removed, new supply lines fitted, sprayer connected and every joint checked dry. This page prices the faucet only; replacing the sink as well is priced separately in our kitchen sink guide.

Double vanity with matte black centerset faucets and a marble-look tiled shower behind

Bathroom Faucet Installation Cost

$230 – $600

The typical project is a standard centerset or widespread bathroom faucet replaced by a plumber in the existing sink holes — old faucet removed, new supply lines fitted, drain pop-up connected and every joint checked dry. This page prices the bathroom sink faucet only; a tub faucet or a new sink is priced separately.

Large white jetted bathtub in a tiled bathroom with a vanity

Bathtub Refinishing Cost

$350 – $630

The typical project is a full professional refinish of a standard built-in tub — stripped, repaired, bonded and sprayed in place, ready to use in a day or two. A liner, an inlay and a full replacement are different projects: the replacement is priced on the bathtub replacement page, and liners are tiered as an alternative below, never blended into this band.

Black and white checkered tile floor with visible grout lines and ground-in grime

Tile and Grout Cleaning Cost

$285 – $675

The typical project is a professional machine clean of the main tiled areas of a home — kitchen, bathrooms and entry — at about $0.50 – $3 per sq ft in Angi. A single small bathroom, grout sealing and damaged tile are tiered or noted separately below; new tile is priced on the tile flooring page.