Home › Cost Guides › Under-Cabinet Lighting Installation
Cost Guide

How Much Does an Under-Cabinet Lighting Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$250 – $700
Most homeowners pay around $400 · Under-cabinet lighting installation typically costs $250 – $700 for a standard kitchen run, with about $400 the figure most standard jobs land near — Angi prices professional installation at $200–$800 with a $400 national average, and its length table prices an average 10–20 linear foot kitchen at $250–$700. EngineerFix prices a professional hardwired 10–15 foot run higher, at $500–$1,200, because that band assumes a licensed electrician concealing wiring and fitting a wall switch — it is published here as the hardwired-scope difference, not blended into the typical band. The $250–$700 typical band is Angi's average-kitchen band, and $400 is Angi's average — a plug-in strip can come in below it, and a large multi-run or smart-controlled kitchen costs far more, while the fixtures, labor and controls below are all inside the total.
typical
$250$700
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Kitchen with a lit strip under gray wall cabinets over the counter and sink

Under-Cabinet Lighting Installation cost at a glance

  • Typical range: $250 – $700
  • Most homeowners pay: around $400
  • Prices vary most by: Installation labor (40–60% of the budget)

Cross-checked against two published sources for this project. Sources used for this page: Angi's under-cabinet lighting installation cost guide, updated Oct 25, 2026 (national average $400, most $200–$800; 5–10 linear ft $100–$350, 10–20 ft $250–$700, 20–30 ft $600–$1,200, 30+ ft $1,000–$1,500+; LED strip $20–$50 per linear foot, puck lights $10–$30 each, fluorescent $15–$40 per fixture; labor 40–60% of total; electricians $50–$120 per hour; hardwired labor $100–$500+; hardwired permits $25–$150; DIY materials $50–$300), EngineerFix's under-cabinet lighting installation cost guides (strip material $5–$15 per linear foot mid-range, channels $3–$8 per foot, bars $20–$40 per foot, puck sets $30–$70, driver $25–$75, dimmer $30–$50; electricians $75–$150 per hour; DIY plug-in 10-foot run materials $150–$350; professional hardwired 10–15 foot run $500–$1,200; complex projects above $1,500) and HomeGuide's light fixture installation cost guide (LED strip installation $70–$400; light bar $200–$500 installed). Sources last checked: October 2026 — HomeGuide, Angi. How we calculate these costs

Cost by scope

Under-Cabinet Lighting Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Plug-in or battery DIY — the budget route$100 – $350The cheap end: Angi prices a small partial installation at $100–$350, and EngineerFix prices the materials for a DIY plug-in LED strip system on an average 10-foot run at $150–$350 including the light source, driver and connectors — no electrician, no new wiring, which is why it prices below a hardwired job
Standard hardwired LED — the typical job$250 – $700The shared band itself: Angi prices an average 10–20 linear foot kitchen at $250–$700 and LED strip at $20–$50 per linear foot — a hardwired LED strip or bar run over the main prep counters, which is the common job and the band this page is built on
Large, multi-run or smart-controlled — the top end$700 – $1,500The expensive end: Angi prices a 30-plus linear foot multi-run kitchen at $1,000–$1,500 or more, and EngineerFix prices complex projects with specialized controls or a new dedicated circuit above $1,500 — more runs, dimmers and smart controls, and a new circuit where no accessible power source exists, are what push a job past the standard band

Where the money goes

Part of the jobShareNote
Fixtures30–45% of totalThe hardware: Angi prices LED strip at $20–$50 per linear foot, puck lights at $10–$30 each and fluorescent fixtures at $15–$40 each, while EngineerFix prices strip material itself at $5–$15 per linear foot before channels — the fixture type is the visible choice, but not the biggest line
Installation labor40–60% of totalThe largest portion on a hardwired job: Angi puts labor at 40–60% of the total, with electricians at $50–$120 per hour, and EngineerFix prices electricians at $75–$150 per hour — concealing wire, drilling through cabinet frames and fitting a switch is the skilled work
Driver, dimmer and controls10–20% of totalThe parts that make the lights usable: EngineerFix prices a driver for a standard kitchen run at $25–$75 and a hardwired wall dimmer at $30–$50 plus junction boxes and wiring, with connectors and clips under $20 for a complete system
Permits and circuit work5–10% of totalThe small line that grows: Angi prices permits for hardwired installations at $25–$150 and notes they are required only for hardwired work — a new dedicated circuit or a switch where none exists is what pushes this line up, and it is the part a plug-in job avoids entirely
Fixtures · 30–45%Installation labor · 40–60%Driver, dimmer and controls · 10–20%Permits and circuit work · 5–10%
Estimator’s note: on an under-cabinet lighting installation, installation labor is usually where quotes swing most (40–60% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
A kitchen with warm LED strip lighting under white wall cabinets over a speckled backsplash: Angi prices LED strip at $20–$50 per linear foot, and EngineerFix prices the strip material itself at $5–$15 per linear foot before channels and labor — the strip under these cabinets is the material line, not the whole job
A kitchen with warm LED strip lighting under white wall cabinets over a speckled backsplash: Angi prices LED strip at $20–$50 per linear foot, and EngineerFix prices the strip material itself at $5–$15 per linear foot before channels and labor — the strip under these cabinets is the material line, not the whole job

What moves the price most

How the lights are powered is the first driver: EngineerFix separates a plug-in setup, which needs only an outlet in reach, from a hardwired setup, which needs a licensed electrician to run 120-volt wiring, drill through studs and fit a switch — Angi prices hardwired labor at $100–$500 or more on top of the fixtures, and EngineerFix prices a hardwired 10–15 foot run at $500–$1,200 all-in. Length is second: Angi's length table runs from $100–$350 for a 5–10 foot partial run through $250–$700 for a 10–20 foot average kitchen to $600–$1,200 for a 20–30 foot large kitchen, because fixtures and labor both scale with the run. Fixture type is third: Angi prices LED strip at $20–$50 per linear foot against puck lights at $10–$30 each, and EngineerFix prices rigid bars at $20–$40 per foot — strips give even continuous light, pucks give pools of light, and bars give a finished look with better diffusion. Finally, controls and circuit access close the bill: EngineerFix prices a dimmer at $30–$50 plus boxes and wiring, and tapping an existing appliance circuit is cheaper than a new dedicated circuit — a kitchen with no accessible power near the cabinets pays for the wire run, not the lights.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
A kitchen with warm under-cabinet lighting glowing over the backsplash and cooktop wall: hardwired work is the labor line — Angi puts labor at 40–60% of the total, and EngineerFix prices a licensed electrician at $75–$150 an hour, which is why a new circuit or switch moves the quote more than the fixtures do
A kitchen with warm under-cabinet lighting glowing over the backsplash and cooktop wall: hardwired work is the labor line — Angi puts labor at 40–60% of the total, and EngineerFix prices a licensed electrician at $75–$150 an hour, which is why a new circuit or switch moves the quote more than the fixtures do

Frequently asked questions

How much does under-cabinet lighting cost per linear foot?

For the fixture line, Angi prices LED strip at $20–$50 per linear foot installed, while EngineerFix prices the strip material itself at $5–$15 per linear foot before aluminum channels at $3–$8 per foot — the gap between those two numbers is the labor, driver and concealment that turn a strip into a finished installation.

Plug-in or hardwired under-cabinet lighting — which should I choose?

Plug-in for a simple upgrade, hardwired for a permanent kitchen: EngineerFix notes plug-in systems need only an outlet in reach and are a few-hours DIY job, while hardwired systems need a licensed electrician and cost more — Angi prices hardwired labor at $100–$500 or more — but hide every wire and switch like the rest of the kitchen.

Do I need a permit for under-cabinet lighting?

Only for hardwired work: Angi prices hardwired permits at $25–$150 depending on local rules, and notes plug-in or battery systems need none. If the job touches 120-volt wiring or adds a circuit, it belongs to a licensed electrician whether or not a permit is pulled.

Can I install under-cabinet lighting myself?

For plug-in or battery systems, yes: EngineerFix prices a DIY plug-in LED strip system for an average 10-foot run at $150–$350 in materials, and Angi puts DIY material costs at $50–$300. Any hardwired component or modification to 120-volt wiring should go to a qualified professional — EngineerFix puts the DIY saving at 60–75% of the pro cost, but only where the job stays low-voltage.

LED strip or puck lights under the cabinets?

Strip for even task light, pucks for accents: Angi prices strip at $20–$50 per linear foot for continuous, shadow-free counter light, against pucks at $10–$30 each that give focused pools and can look uneven on a long run. Most standard kitchens on this page use strip for the prep counters and save pucks for a display shelf or a short run.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Under-Cabinet Lighting Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides