Home › Cost Guides › Fence Gate Installation
Cost Guide

How Much Does a Fence Gate Installation Cost? (2026)

By Ahsan ul Haq · Last updated: 11 November 2026 · Planning estimate — not a quote · How we estimate

Typical range
$300 – $800
Most homeowners pay around $500 · Fence gate installation typically costs $300 – $800 for a standard single walk gate, with about $500 the figure most jobs land near — the overlap where HomeGuide's vinyl gate band ($150–$780 installed), its aluminum gate band ($450–$1,000) and its chain-link walk-through band ($130–$450 installed) meet. Angi's much higher city averages, around $2,000, are published for a broader gate category that includes driveway and automatic gates, and are flagged as such below rather than averaged in.
typical
$300$800
Low end = minor scope  ·  marker = typical middle  ·  high end = major scope. Add 10–20% contingency to any budget.
Wood gate leaf with a steel handle set in a horizontal-board wood fence beside a house

Fence Gate Installation cost at a glance

  • Typical range: $300 – $800
  • Most homeowners pay: around $500
  • Prices vary most by: Gate leaf and frame (30–40% of the budget)

Cross-checked against three published sources for this project. Sources used for this page: Angi's city gate guides, updated July 2026 (most-pay bands roughly $777–$3,739 per city with averages about $2,000–$2,253 across gate types; 4 ft gates $200–$455, 8 ft $405–$910, 12 ft $1,010–$3,410; manual driveway gates $300–$1,215, automatic driveway gates $1,920–$6,055; labor $50–$60 per hour for 4–6 hours), HomeGuide's material gate guides (vinyl gate $150–$780 installed; aluminum gate $450–$1,000, large driveway gates with openers $2,000–$6,000; chain-link single walk-through $130–$450 installed, double drive-through $200–$1,000 installed; wrought-iron gate materials $200–$650) and Fixr's gate figures (walk gate $50–$400 installed; driveway gate $1,000–$6,000, averaging $4,000 for a 12 ft automatic double wood gate) — the page's typical band is the walk-gate overlap of the HomeGuide bands, and Angi's higher average is published as a broader-category disagreement, not averaged in. Sources last checked: October 2026 — HomeGuide, Fixr, Angi. How we calculate these costs

Cost by scope

Fence Gate Installation cost ranges by scope — chart of the table below
ScopeTypical costWhat it includes
Simple chain-link or basic wood walk gate$150 – $450The cheap end: HomeGuide prices a chain-link single walk-through gate at $130–$450 installed ($80–$200 for materials alone), and Fixr's walk-gate band starts at $50 — a plain leaf on posts, one latch, no ornament
Standard wood or vinyl walk gate — the typical job$300 – $800The shared band itself: HomeGuide's vinyl gate at $150–$780 installed and aluminum at $450–$1,000, with wood gates in the same middle ground — a framed leaf, solid posts, hinges and a latch, matched to the fence
Double gate or ornamental metal gate$800 – $2,000The expensive end: HomeGuide prices a double drive-through chain-link gate at $200–$1,000 installed and large aluminum driveway gates with openers at $2,000–$6,000 — two leaves, heavier posts and ornamental or wrought-iron work push a pedestrian gate toward this tier

Where the money goes

Part of the jobShareNote
Gate leaf and frame30–40% of totalThe gate itself: the leaf, frame and infill — wood, vinyl, aluminum or chain-link — sized to the opening, with wider and ornamental leaves costing more
Posts, hinges and latch hardware20–30% of totalWhat holds it and swings it: set posts, heavy hinges and a latch that actually closes — the parts that decide whether the gate sags in a year
Installation labor25–35% of totalThe fitting: Angi's city gate guides price labor at $50–$60 per hour for 4–6 hours ($200–$360) on a standard gate, more where posts need concrete or ground is uneven
Removal, permits and extras5–10% of totalThe tail: hauling an old gate away, a permit where the locality requires one, and small extras such as a self-closing hinge or a lock
Gate leaf and frame · 30–40%Posts, hinges and latch hardware · 20–30%Installation labor · 25–35%Removal, permits and extras · 5–10%
Estimator’s note: on a fence gate installation, gate leaf and frame is usually where quotes swing most (30–40% of total of a typical budget). Ask every contractor to itemize that line in writing — totals are only comparable when that part is.
A wide wood gate with steel posts and a ground track: wider and double gates are the $800–$2,000 tier, where two leaves, heavier posts and more hardware push the price above a single walk gate
A wide wood gate with steel posts and a ground track: wider and double gates are the $800–$2,000 tier, where two leaves, heavier posts and more hardware push the price above a single walk gate

What moves the price most

Width is the first driver. A single 3–4 ft walk gate is the typical job in this guide; Angi's city tables price 4 ft gates at $200–$455 against $405–$910 for 8 ft and $1,010–$3,410 for 12 ft, and a double gate is two leaves, two sets of hardware and heavier posts. Material is second: HomeGuide puts chain-link walk-through gates lowest, vinyl in the middle and aluminum higher, with wrought-iron materials alone at $200–$650 before labor. Posts and ground are third: a gate is only as good as its posts — soft ground, a slope or an old post that needs replacing all add labor and concrete. Finally, automation is a different job: Angi prices automatic driveway gates at $1,920–$6,055 and Fixr at $1,000–$6,000, which is why this guide covers pedestrian and manual gates and points driveway automation to our driveway gate guide.

Work out your quantities: before you compare quotes, run your measurements through our free remodeling calculators (paint, tile, concrete and flooring) — each one shows its formula and runs entirely in your browser.

Costs in your city

Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

How this estimate was built: the range on this page is a synthesis of at least three published industry sources (national cost guides and the Remodeling Magazine Cost vs. Value data among them), cross-checked in October 2026. We publish planning ranges, never a single pretend-precise price. Full method: How We Estimate Costs.
Horizontal wood boards and a post in close view: matching the gate to the fence's wood and board style is what makes a new gate look built in rather than bolted on — and mismatched boards are the giveaway of a cheap gate job
Horizontal wood boards and a post in close view: matching the gate to the fence's wood and board style is what makes a new gate look built in rather than bolted on — and mismatched boards are the giveaway of a cheap gate job

Frequently asked questions

How much does it cost to install a fence gate?

Typically $300–$800 for a standard single walk gate, with about $500 the figure most jobs land near — HomeGuide's vinyl ($150–$780 installed), aluminum ($450–$1,000) and chain-link walk-through ($130–$450 installed) bands overlap there.

Why does Angi report around $2,000 for a gate?

Because Angi's gate category is broader: its city guides average roughly $2,000–$2,253 across gate types including manual driveway gates ($300–$1,215) and automatic driveway gates ($1,920–$6,055). A plain pedestrian walk gate is a much smaller job, and this guide's $300–$800 band is the walk-gate overlap, not the all-gates average.

What costs more — wood, vinyl, aluminum or chain-link?

Chain-link is cheapest (HomeGuide: $130–$450 installed for a single walk-through), vinyl and wood sit in the middle ($150–$780 for vinyl), and aluminum and ornamental metal run higher ($450–$1,000 for a standard aluminum gate, more for double or ornamental work).

Do I need a permit for a fence gate?

Usually not for a like-for-like gate in an existing fence, but rules are local — height limits, setbacks and HOA rules can all apply, and a new fence run with a gate is more likely to need approval than a replacement leaf. Check with your city or county before the posts go in.

How do I stop a new gate from sagging?

With posts and hardware sized for the leaf: set posts in concrete, use hinges rated for the gate's weight, and add a diagonal brace or anti-sag kit on wide wood gates. Sagging is almost always a post or hinge problem, not a leaf problem — and it is the reason the posts-and-hardware line is 20–30% of this job.

Is an automatic driveway gate included in this price?

No — automatic driveway gates are a separate, much larger job: Angi prices them at $1,920–$6,055 and Fixr at $1,000–$6,000, against $300–$1,215 for a manual driveway gate. See our driveway gate installation guide for that job.

Before you sign: get at least 3 written local quotes for the same written scope, confirm permits and who pulls them, and keep a 10–20% contingency separate from the contract price.

Ahsan ul Haq — Editor, Remodel Cost Hub

Ahsan compiles and edits the cost guides on Remodel Cost Hub, cross-checking every range against at least three published sources before it is published — the full method is on our Methodology page. Spot an error on this page? Send a correction.

Fence Gate Installation cost range graphic
Save this range for later: Pin it on Pinterest

Related cost guides

Freeform pool with a round stone spa set in a stamped-concrete surround

Pool Deck Installation Cost

$5,000 – $12,000

Pool deck installation typically costs $5,000 – $12,000, with about $5,000 the figure most standard jobs land near — Angi prices an aboveground pool deck at a national average of $5,000 with most homeowners spending $3,000–$12,000, HomeGuide prices a pool deck at $25–$50 per square foot or $5,000–$20,000 total for 200–400 square feet, and DeckCostGuide prices a raised wood pool deck at $25–$70 and a raised composite deck at $40–$80 per square foot. The $5,000–$12,000 typical band is Angi's most-common band, inside HomeGuide's wider total, and $5,000 is Angi's published average — a ground-level concrete or paver surround costs far less, and a large premium deck costs far more.

Aerial view of a backyard inground pool with an attached spa

Pool Heater Installation Cost

$1,900 – $4,500

Pool heater installation typically costs $1,900 – $4,500 for a standard inground pool, with about $3,100 the figure most jobs land near — Angi averages $3,100 across 1,019 verified projects with most at $1,864–$4,351, HomeGuide averages $3,300 with a range of $1,600–$5,200, and HomeGnome puts the installed range at $1,670–$4,410. The heater, labor, hookup lines, permits and old-heater removal below are all inside the total, while the monthly running cost — gas $200–$400 in Angi, heat pump $120–$200 — is not, and is published separately so it is not mistaken for part of the install price.

Metal pool barrier with looped tops standing in a swimming pool

Pool Fence Installation Cost

$1,500 – $6,800

Pool fence installation typically costs $1,500 – $6,800 for about 150 linear feet of standard mesh or aluminum safety fencing, with about $4,150 the midpoint of that band rather than a guide-stated average — HomeGuide prices a 150-foot run at $1,500–$6,800 at $10–$45 per linear foot with a national average of $7,800 for 200–300 feet, HomeGnome prices pool fencing at $17–$34 per linear foot with an average of $25.50, and Bob Vila, citing HomeAdvisor and Angi, puts the typical project at $1,500–$10,000 with an average of $6,500. The guides agree that material is the whole story: mesh is the cheap end, aluminum the standard permanent choice, and tempered glass the top end — published here as separate tiers, not averaged away.

Corrugated galvanized-steel raised bed planted with flowering strawberries

Raised Garden Bed Installation Cost

$1,200 – $3,000

Raised garden bed installation typically costs $1,200 – $3,000, with about $2,000 the figure most standard projects land near — HomeGuide prices a custom-built 5-by-12-foot raised bed at $1,200–$4,000 installed, Angi prices professional flowerbed installation at $1,000–$3,000 with a $2,000 average, and CostToRenovate prices a raised-bed installation at $400–$2,500 with a $1,200 national average for a single bed. The $1,200–$3,000 typical band is the overlap of HomeGuide's custom-built band and Angi's professional band for a standard project of one to three beds, professionally built and filled, and $2,000 is Angi's published average — a single DIY kit bed costs far less, and a multi-bed stone or composite garden with irrigation costs far more.

American flag flying from a silver flagpole with a ball finial against a blue sky

Flagpole Installation Cost

$400 – $1,000

Flagpole installation typically costs $400 – $1,000, with about $850 the figure most standard jobs land near — Angi prices flagpole installation at a national average of $850 with most projects at $400–$1,000, HomeGuide prices the pole-only pieces of the same job from $80–$200 for a wall-mounted kit to $600–$1,200 for a one-piece aluminum pole plus $450–$700 of in-ground installation labor, and EngineerFix prices a 20-foot aluminum pole at $200–$800 with professional labor at $500–$2,000. The $400–$1,000 typical band is Angi's most-common band, corroborated by HomeGuide's pole-plus-labor arithmetic, and $850 is Angi's published average — a wall-mounted pole costs far less, and a tall fiberglass or custom wooden pole costs far more.

Spacious garage with blue and red storage cabinets along the wall

Garage Storage Installation Cost

$2,000 – $5,000

A garage storage system typically costs $2,000 – $5,000 for a standard two-car garage wall, with about $3,500 the figure most standard jobs land near — Angi prices a medium two-car garage cabinet job at $2,000–$5,000 and prefab cabinet systems at $2,000–$6,000, Sands Cabinets prices a standard two-car setup with tall cabinets, uppers and lowers at $2,000–$5,000 for 70–80% of homeowners, and Croc Coatings puts most garage cabinet projects at $500–$6,000. The $2,000–$5,000 typical band is Angi's two-car band, and $3,500 is its midpoint — a single wall of shelving can come in below it, and a full custom wall with a workbench costs far more, while the cabinets, labor and accessories below are all inside the total.