Landscape Lighting Installation cost at a glance
- Typical range: $2,000 – $6,000
- Most homeowners pay: around $3,500
- Prices vary most by: Fixtures & lamps (35–50% of the budget)
Cross-checked against two published sources for this project. Sources used for this page: the Angi landscape lighting cost guide, HomeGuide's landscape lighting cost guide and the Kloe Lighting outdoor lighting price guide. Sources last checked: October 2026 — HomeGuide, Angi. How we calculate these costs
Cost by scope

| Scope | Typical cost | What it includes |
|---|---|---|
| Small system — 4 to 8 fixtures | $800 – $2,000 | Angi's small-project band: the front path, the steps and one or two accents at the entry. HomeGuide's per-fixture maths agrees at the low end — at its $80–$300 a fixture installed, eight basic fixtures run $640–$2,400 before the transformer. |
| Standard full system — the typical job | $2,000 – $6,000 | Front and back coverage: 9–16 fixtures at $2,000–$4,500 in Angi's size table, and 10–20 lights at $800–$6,000 in HomeGuide. Angi's national average is $3,500, and the Kloe Lighting price guide publishes the same $2,000–$6,000 professional band at the same $3,500 average for a full system with LED fixtures, wiring and labour. |
| Large or custom design — 17+ fixtures | $4,500 – $10,000 | Angi's large-project band: multi-zone layouts, tree-mounted downlighting, water-feature lights and smart controls. Premium brass fixtures at the top of Angi's $100–$500 per-fixture table and separate design fees push elaborate properties above this band. |
Where the money goes
| Part of the job | Share | Note |
|---|---|---|
| Fixtures & lamps | 35–50% | HomeGuide splits its $80–$300 installed fixture at $50–$200 for the fixture and supplies against $30–$100 of labour and wiring; Angi prices fixtures by type at $100–$500 installed, with brass and copper bodies at the top. This share is derived from those per-fixture splits and is labelled as derived in the method box |
| Labour, trenching & wiring | 30–$45% | Angi prices labour at $50–$100 an hour and HomeGuide's electricians at $50–$130; trenching alone runs $5–$12 a linear foot in HomeGuide. Long runs, hardscape crossings and slopes are where this share grows |
| Transformer, controls, permits & aiming | 10–20% | The transformer is $200–$500 installed in HomeGuide and permits run $50–$300 in Angi where new wiring requires one; the after-dark aiming visit is the labour line that cut-price quotes most often quietly drop |

What moves the price most
Fixture count is the budget. Every guide prices the system fixture by fixture — Angi at $100–$500 installed by type (path $100–$250, spotlights $150–$350, floodlights $200–$500, step lights $100–$300) and HomeGuide at $80–$300 all-in — so two quotes are only comparable at the same count. Fixture material is the second price: plastic and aluminium bodies sit low in both guides, brass and copper at the top, and coastal air corrodes the cheap end fastest. The invisible work is real money: a transformer at $200–$500 installed (HomeGuide), a new GFCI outlet at $150–$350 where the house lacks one, and trenching at $5–$12 a linear foot. Controls and zones add up — timers are standard, smart and app controls are a premium in Angi — and permits at $50–$300 apply where new line-voltage wiring is run. Running the finished system is cheap by comparison: $20–$60 a year in HomeGuide for LED.
Worked example: how a typical landscape lighting installation budget breaks down
Take the typical job — a 12-fixture low-voltage LED system: path lights down the front walk, uplights on two trees and the facade, cable trenched and buried, transformer on the garage wall with a timer, and a return visit after dark to aim every fixture. Here is a realistic $3,500 version of that invoice, at Angi's national average: The budget below totals $3,500 — the "most homeowners pay around" figure from the top of this page — split using this page's own cost breakdown. It shows how a real quote at that level is usually composed; every line is built from the ranges on this page, and it is an illustration, not a quote for your project.
| Line item | Example budget |
|---|---|
| Fixtures — 12 low-voltage LED path & accent fixtures | $1,500 |
| Labour, trenching & wiring | $1,400 |
| Transformer & timer control | $400 |
| Permits, after-dark aiming & cleanup | $200 |
| Total | $3,500 |
What most people get wrong
- Comparing per-fixture quotes that hide different scopes. One installer prices the fixture alone, another includes its share of transformer, cable and trenching. HomeGuide's split — $50–$200 fixture and supplies plus $30–$100 labour and wiring — is the conversion to demand on every quote.
- Lighting the path like a runway. Fixtures every step in a straight row is the most common design failure, and it costs more, not less: HomeGuide spaces path lights 6 to 10 feet apart in pools of light, and fewer, aimed fixtures outperform a dotted line.
- Undersizing the transformer to save $100. The transformer must carry the whole load with headroom for the fixtures you will add later; HomeGuide prices it at $200–$500 installed, and a maxed-out unit means dim far fixtures and a second purchase inside a year.
- Buying plastic fixtures for a coastal or freeze-thaw yard. Both guides put brass and copper at the top of the fixture table for a reason — cheap bodies corrode and crack where salt air and hard winters work on them, and the replacement visit costs more than the upgrade did.
Costs in your city
Landscape lighting follows electrician rates and permit regimes together. Angi prices installation labour at $50–$100 an hour and HomeGuide's electricians at $50–$130, so high-wage metros land at the top of the $2,000–$6,000 band while the same 12-fixture design prices lower where crew rates sit low. Permits are the second local variable — $50–$300 in Angi, and only where new line-voltage wiring is run, which is why low-voltage scopes permit lightly in most cities. Climate writes the third line: coastal salt air pushes the fixture choice toward the brass end of the table, and wet or freeze-prone regions pay for weatherproofing and deeper, better-sealed connections (Angi). Ask each installer for the fixture count, the per-fixture split and whether the transformer and aiming visit are inside the number, and city quotes become comparable line by line.
How we got these numbers
Cross-checked against the Angi landscape lighting cost guide — opened and read in full this run (average $3,500, most homeowners paying $2,000–$6,000, small systems from $800 and large custom work to $10,000; by size: 4–8 fixtures $800–$2,000, 9–16 at $2,000–$4,500, 17+ at $4,500–$10,000; per fixture $100–$500 by type; labour $50–$100 an hour; permits $50–$300; DIY $500–$3,150 against professional $1,650–$6,800), HomeGuide's landscape lighting cost guide — opened and read in full ($80–$300 per fixture installed, $800–$6,000 for 10–20 lights; fixture and supplies $50–$200 against labour and wiring $30–$100; transformer $200–$500 installed; trenching $5–$12 a linear foot; electricians $50–$130 an hour; running cost $20–$60 a year) and the Kloe Lighting outdoor lighting price guide (professional installation $2,000–$6,000, average $3,500; medium 10–20 fixture systems $2,000–$5,500; transformer $200–$600). The typical band and most-pay figure are the totals all three publish. The per-fixture splits genuinely disagree — HomeGuide's older guide totals $80–$300 a fixture against Angi's $100–$500 by type — so this page publishes both splits side by side rather than blending them, and frames its tiers on the project totals where the sources agree. Breakdown shares are derived from HomeGuide's per-fixture split and are labelled as derived on the page.

Frequently asked questions
How much does landscape lighting cost per fixture, installed?
It depends which guide's split you use, and this page shows both: HomeGuide totals $80–$300 a fixture installed ($50–$200 of it the fixture and supplies, $30–$100 labour and wiring), while Angi prices fixtures by type at $100–$500 installed. On a whole system the two agree — the typical 10–16 fixture job lands at $2,000–$6,000 either way.
How many landscape lights does a house need?
Angi's size table is the practical frame: 4–8 fixtures cover an entry and walkway, 9–16 cover front and back, and 17+ is full-property work. Within a run, HomeGuide spaces path lights 6 to 10 feet apart and works to roughly one light per 50 to 60 sq ft of lit area. More fixtures placed evenly is the classic overspend — a few aimed well beat a runway.
Should I choose low-voltage, line-voltage or solar?
Low-voltage (12-volt) LED is the standard professional system on this page: safe cable, bright and consistent output, and $20–$60 a year to run in HomeGuide. Line-voltage suits security floods and needs a licensed electrician and often a permit. Solar stakes cost the least and need no wiring, but Angi notes their brightness is inconsistent — they are garden ornaments, not a lighting system.
How much does landscape lighting cost to run?
Very little with LED. HomeGuide puts a typical system at $20–$60 a year, about $2–$5 a month; Angi puts a larger 15–20 light LED system at $5–$15 a month. Halogen is the expensive legacy option — Angi notes it can cost up to five times the LED running cost — which is why conversions price the lamp swap into the job.
Can I install landscape lighting myself?
A simple low-voltage path run is genuinely DIY-able: Angi prices DIY at $500–$3,150 against $1,650–$6,800 professionally installed. What the professional price buys is the design, the voltage-drop maths on long runs, sealed underground connections and the after-dark aiming. Anything line-voltage, or a new circuit for the transformer, belongs to a licensed electrician.






