Pool Pump Replacement cost at a glance
- Typical range: $800 – $1,800
- Most homeowners pay: around $1,300
- Prices vary most by: Pump unit (50–65% of the budget)
Cross-checked against two published sources for this project. Sources used for this page: Angi's pool pump replacement guide, updated September 16, 2026 (national average $1,300, most $700–$4,000; units $300–$2,500 by type: low-head $250–$1,600, medium-head $400–$2,500, variable-speed $800–$2,500; pro labor $200–$500; timer $50–$100; underground excavation $100–$200; bearing repair $65–$300, motor $250–$2,000; repair-over-50%-of-new rule), HomeGuide's pool pump cost guide (replacement $300–$1,600 total; pump $200–$1,200, labor $100–$400; variable-speed $800–$2,000 installed; filter replacement $250–$1,700 separately; electrician $40–$100 per hour, plumber $45–$150 per hour; exterior receptacle $200–$275) and EngineerFix's pool pump cost guide (single-speed units $250–$700, dual-speed $300–$1,600; straightforward install labor $100–$400, $280–$500+ with electrical or plumbing modifications) — the page's typical band is the standard-swap overlap, and its $1,300 most-pay figure is Angi's published average. Sources last checked: October 2026 — HomeGuide, Angi. How we calculate these costs
Cost by scope

| Scope | Typical cost | What it includes |
|---|---|---|
| Single-speed, like-for-like swap | $700 – $1,200 | The cheap end: Angi's band starts at $700, and HomeGuide totals a same-size swap at $300–$1,600 — same horsepower, same plumbing and wiring |
| Standard dual-speed or variable-speed — the typical job | $800 – $1,800 | The shared band itself: Angi's $1,300 average, variable-speed units at $800–$2,500 in Angi and $800–$2,000 installed in HomeGuide |
| Large pool, premium variable-speed or replumbed/rewired — the top end | $1,800 – $4,000 | The expensive end: Angi's band runs to $4,000, and EngineerFix notes electrical or plumbing modifications push labor from $100–$400 to $280–$500+ before the unit |
Where the money goes
| Part of the job | Share | Note |
|---|---|---|
| Pump unit | 50–65% of total | The unit ladder: Angi prices units at $300–$2,500 by type, HomeGuide at $200–$1,200, and EngineerFix prices single-speed units at $250–$700 and dual-speed at $300–$1,600 |
| Installation labor | 20–35% of total | The swap: Angi prices pro labor at $200–$500, HomeGuide at $100–$400 for a like-for-like swap |
| Electrical, plumbing mods, timer and disposal | 10–20% of total | The extras: Angi prices timer installation at $50–$100 and underground excavation at $100–$200 where it applies, and HomeGuide prices an exterior receptacle at $200–$275 |

What moves the price most
Pump type is the first driver. Angi prices units at $300–$2,500 by type, and EngineerFix prices single-speed units at $250–$700 against dual-speed at $300–$1,600 — variable-speed costs more to buy and less to run, which is the trade the guides keep returning to. Like-for-like or upgrade is second: HomeGuide notes a same-size, same-model swap needs no plumbing or electrical changes, while EngineerFix puts modified labor at $280–$500+ against $100–$400 for a straightforward swap. Pool size is third: horsepower follows pool volume, so a large pool's pump costs more than a small pool's before labor. Finally, the repair question: Angi's rule is that a repair over 50% of a new pump's price is the wrong call — a bearing at $65–$300 is a repair, a motor at $250–$2,000 on an old pump often is not.
Costs in your city
Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

Frequently asked questions
How much does pool pump replacement cost?
Typically $800–$1,800 for a standard swap, with about $1,300 the figure most jobs land near — Angi's average, against HomeGuide's $300–$1,600 total for a straightforward replacement.
Single-speed or variable-speed pump — which should I choose?
Variable-speed costs more up front — $800–$2,500 for the unit in Angi — and runs cheaper, because it can filter at low speed most of the day. Single-speed is cheapest to buy and most expensive to run; the saving is in electricity over the pump's life, not in the quote.
Should I repair or replace my pool pump?
Angi's rule: if the repair costs more than 50% of a new pump, replace. A bearing at $65–$300 is a repair; a motor at $250–$2,000 on a pump over eight years old is usually the point to replace.
Does a pool pump swap need an electrician?
Professional installation is the priced scope here, because the job mixes water and electricity. HomeGuide prices electrician time at $40–$100 per hour and plumber time at $45–$150 per hour where wiring or pipework has to change.
What is not included in this price?
A new filter, heater or automation is not in this band: HomeGuide prices a filter replacement separately at $250–$1,700, and a pump-and-filter job together is a larger quote than a pump swap alone.






