Garbage Disposal Repair cost at a glance
- Typical range: $140 – $310
- Most homeowners pay: around $230
Cross-checked against three published sources for this project. Sources used for this page: Angi's garbage disposal repair cost guide (updated July 2026, average $230, most paying $140–$310), HomeGuide's garbage disposal repair cost guide (national average $175, range $100–$250) and Thumbtack's garbage disposal repair cost guide (national average $100–$230). Sources last checked: October 2026 — HomeGuide, Angi, Thumbtack. How we calculate these costs
Cost by scope

| Scope | Typical cost | What it includes |
|---|---|---|
| Minor fix — jam, clog, seal | $70 – $180 | The small jobs: clogged at $70–$200, leaking at $80–$180 and jammed at $75–$175 (HomeGuide), with Angi noting minor seal or jam fixes can be under $10 as DIY |
| Standard repair — the typical band | $140 – $310 | The shared band itself: continuous-feed repairs at $80–$270 and batch-feed at $70–$310 (Angi), inside HomeGuide's $100–$250 average range |
| Major repair — motor, impeller, electrical | $130 – $550 | The expensive end: a loose or broken impeller at $130–$330 and a unit that won't switch on at $70–$550 (HomeGuide), with a broken motor at $150 or more (Angi) |
Where the money goes
| Part of the job | Share | Note |
|---|---|---|
| Labour | $50 – $120 per hour | Angi's hourly band, plus a site fee of around $50; HomeGuide's labour band is $50–$125 per hour |
| Labour + service call | $150 – $300 | Angi's combined budget figure for professional labour and a service call |
| Clogged | $70 – $200 | HomeGuide's band: disassemble, remove obstructions, reset and flush |
| Leaking | $80 – $180 | HomeGuide's band: tighten connections, replace the flange assembly and gaskets, or replace the dishwasher connection hose |
| Jammed (humming only) | $75 – $175 | HomeGuide's band: disassemble, remove obstructions, reset the unit and flywheel cutting plate |
| Won't switch on | $70 – $550 | HomeGuide's band: reset, fix loose wiring, replace a faulty switch or circuit, or replace the motor or the unit |
| Impeller / flywheel | $130 – $330 | HomeGuide's band for a loose or broken impeller, flywheel or shredding plate |
| Motor (Angi part figure) | $70 – $130 | Angi's motor part figure; Angi notes a broken motor repair can cost $150 or more in total |
| Grinding plates (Angi part figure) | $15 – $55 | Angi's grinding-plate part figure |
| Gasket / seal (Angi part figure) | $3 – $20 | Angi's gasket and seal part figure |
| Sink flange (Angi part figure) | $8 – $18 | Angi's sink-flange part figure |
| Discharge pipe (Angi part figure) | $10 – $25 | Angi's discharge-pipe part figure |
| Replacement unit, installed | $200 – $550 | HomeGuide's replacement band, against Angi's $150–$950 replacement range with a $550 average |

What moves the price most
Disposal type sets the starting band: continuous-feed repairs run $80–$270 against batch-feed at $70–$310 (Angi). Problem type matters more: Angi divides disposal faults into grinding, electrical and sealing, and a sealing fault is usually the cheapest while a motor fault is usually the dearest. Age decides repair versus replace: disposals last 7–12 years at about 10 (Angi), repair is the good option at 8 years or younger (Angi), and replacement makes sense as the unit approaches 10 years with frequent leaks, clogs or noises. Replacement runs $200–$550 installed (HomeGuide), so a $130–$330 impeller job on a 9-year-old unit is already at the decision line, and labour is the largest share: Angi prices it at $50–$120 per hour plus around $50 for the site visit.
Costs in your city
Labor is the biggest variable in any remodel, and labor is local — the same bathroom can price very differently in Houston than in Boston. We are adding city editions metro by metro, each with its own labor index, permit notes and climate factors, written for that city rather than copied from this page. Wave 1: Houston, Dallas–Fort Worth, Phoenix, Atlanta, Miami–South Florida, Orlando, Tampa, Charlotte, Austin and San Antonio. Until your city's page is live, use the national range here and weight it the way contractors do: Sun Belt labor often prices near or below the national middle, while coastal California and the Northeast metros often price well above it.

Frequently asked questions
How much does garbage disposal repair cost?
Typically $140–$310, with about $230 the most-pay figure. Angi's 2026 average is $230 inside $140–$310, HomeGuide's national average is $175 inside $100–$250, and Thumbtack puts the national average at $100–$230 — the three sources agree on this page's band.
How much does it cost to fix a jammed garbage disposal?
$75–$175 (HomeGuide) for a jammed unit that only hums, and $70–$200 for a clogged unit. Never put hands inside the disposal: Angi's safe DIY steps are the reset button, the breaker and the hex key.
How much does a leaking garbage disposal cost to fix?
$80–$180 (HomeGuide), usually a flange assembly, gasket or dishwasher connection hose. Angi's part figures for the same job are a gasket or seal at $3–$20 and a sink flange at $8–$18, before labour.
Should I repair or replace my garbage disposal?
Repair if it is 8 years old or younger and the fault is a seal, jam or switch (Angi); replace if it is approaching 10 years, the motor is broken ($150 or more, Angi) or faults repeat. A replacement unit installed runs $200–$550 (HomeGuide).
Why won't my garbage disposal switch on?
HomeGuide prices that fault at $70–$550 because it spans a reset, loose wiring, a faulty switch or circuit, or a dead motor. Check the reset button and the breaker first (Angi); if the motor will not run with a clear chamber and a freely turning flywheel, Angi's guidance is replacement, not repair.






